net: ethernet: stmmac: update to support all PHY config for stm32mp157c.
authorChristophe Roullier <christophe.roullier@st.com>
Tue, 5 Mar 2019 08:29:24 +0000 (09:29 +0100)
committerDavid S. Miller <davem@davemloft.net>
Fri, 8 Mar 2019 19:48:19 +0000 (11:48 -0800)
Update glue codes to support all PHY config on stm32mp157c
 PHY_MODE (MII,GMII, RMII, RGMII) and in normal, PHY wo crystal (25Mhz),
PHY wo crystal (50Mhz), No 125Mhz from PHY config.

Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/stmicro/stmmac/dwmac-stm32.c

index d1cf145b8986015e83970760425b1748afc89d2f..062a600fa5a76310571f9aa6db84639c81546c09 100644 (file)
 
 #define SYSCFG_MCU_ETH_MASK            BIT(23)
 #define SYSCFG_MP1_ETH_MASK            GENMASK(23, 16)
+#define SYSCFG_PMCCLRR_OFFSET          0x40
 
 #define SYSCFG_PMCR_ETH_CLK_SEL                BIT(16)
 #define SYSCFG_PMCR_ETH_REF_CLK_SEL    BIT(17)
+
+/*  Ethernet PHY interface selection in register SYSCFG Configuration
+ *------------------------------------------
+ * src  |BIT(23)| BIT(22)| BIT(21)|BIT(20)|
+ *------------------------------------------
+ * MII   |   0  |   0    |   0    |   1   |
+ *------------------------------------------
+ * GMII  |   0  |   0    |   0    |   0   |
+ *------------------------------------------
+ * RGMII |   0  |   0    |   1    |  n/a  |
+ *------------------------------------------
+ * RMII  |   1  |   0    |   0    |  n/a  |
+ *------------------------------------------
+ */
 #define SYSCFG_PMCR_ETH_SEL_MII                BIT(20)
 #define SYSCFG_PMCR_ETH_SEL_RGMII      BIT(21)
 #define SYSCFG_PMCR_ETH_SEL_RMII       BIT(23)
 #define SYSCFG_MCU_ETH_SEL_MII         0
 #define SYSCFG_MCU_ETH_SEL_RMII                1
 
+/* STM32MP1 register definitions
+ *
+ * Below table summarizes the clock requirement and clock sources for
+ * supported phy interface modes.
+ * __________________________________________________________________________
+ *|PHY_MODE | Normal | PHY wo crystal|   PHY wo crystal   |No 125Mhz from PHY|
+ *|         |        |      25MHz    |        50MHz       |                  |
+ * ---------------------------------------------------------------------------
+ *|  MII    |   -   |     eth-ck    |        n/a         |       n/a        |
+ *|         |        |              |                    |                  |
+ * ---------------------------------------------------------------------------
+ *|  GMII   |   -   |     eth-ck    |        n/a         |       n/a        |
+ *|         |        |               |                    |                 |
+ * ---------------------------------------------------------------------------
+ *| RGMII   |   -   |     eth-ck    |        n/a         |  eth-ck (no pin) |
+ *|         |        |               |                    |  st,eth-clk-sel  |
+ * ---------------------------------------------------------------------------
+ *| RMII    |   -   |     eth-ck    |      eth-ck        |       n/a        |
+ *|         |        |              | st,eth-ref-clk-sel |                  |
+ * ---------------------------------------------------------------------------
+ *
+ * BIT(17) : set this bit in RMII mode when you have PHY without crystal 50MHz
+ * BIT(16) : set this bit in GMII/RGMII PHY when you do not want use 125Mhz
+ * from PHY
+ *-----------------------------------------------------
+ * src  |         BIT(17)       |       BIT(16)      |
+ *-----------------------------------------------------
+ * MII   |           n/a        |         n/a        |
+ *-----------------------------------------------------
+ * GMII  |           n/a         |   st,eth-clk-sel   |
+ *-----------------------------------------------------
+ * RGMII |           n/a         |   st,eth-clk-sel   |
+ *-----------------------------------------------------
+ * RMII  |   st,eth-ref-clk-sel         |         n/a        |
+ *-----------------------------------------------------
+ *
+ */
+
 struct stm32_dwmac {
        struct clk *clk_tx;
        struct clk *clk_rx;
        struct clk *clk_eth_ck;
        struct clk *clk_ethstp;
        struct clk *syscfg_clk;
-       bool int_phyclk;        /* Clock from RCC to drive PHY */
+       int eth_clk_sel_reg;
+       int eth_ref_clk_sel_reg;
        int irq_pwr_wakeup;
-       u32 mode_reg;           /* MAC glue-logic mode register */
+       u32 mode_reg;            /* MAC glue-logic mode register */
        struct regmap *regmap;
        u32 speed;
        const struct stm32_ops *ops;
@@ -103,7 +157,7 @@ static int stm32mp1_clk_prepare(struct stm32_dwmac *dwmac, bool prepare)
                if (ret)
                        return ret;
 
-               if (dwmac->int_phyclk) {
+               if (dwmac->clk_eth_ck) {
                        ret = clk_prepare_enable(dwmac->clk_eth_ck);
                        if (ret) {
                                clk_disable_unprepare(dwmac->syscfg_clk);
@@ -112,7 +166,7 @@ static int stm32mp1_clk_prepare(struct stm32_dwmac *dwmac, bool prepare)
                }
        } else {
                clk_disable_unprepare(dwmac->syscfg_clk);
-               if (dwmac->int_phyclk)
+               if (dwmac->clk_eth_ck)
                        clk_disable_unprepare(dwmac->clk_eth_ck);
        }
        return ret;
@@ -122,7 +176,7 @@ static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
 {
        struct stm32_dwmac *dwmac = plat_dat->bsp_priv;
        u32 reg = dwmac->mode_reg;
-       int val;
+       int val, ret;
 
        switch (plat_dat->interface) {
        case PHY_INTERFACE_MODE_MII:
@@ -131,19 +185,22 @@ static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
                break;
        case PHY_INTERFACE_MODE_GMII:
                val = SYSCFG_PMCR_ETH_SEL_GMII;
-               if (dwmac->int_phyclk)
+               if (dwmac->eth_clk_sel_reg)
                        val |= SYSCFG_PMCR_ETH_CLK_SEL;
                pr_debug("SYSCFG init : PHY_INTERFACE_MODE_GMII\n");
                break;
        case PHY_INTERFACE_MODE_RMII:
                val = SYSCFG_PMCR_ETH_SEL_RMII;
-               if (dwmac->int_phyclk)
+               if (dwmac->eth_ref_clk_sel_reg)
                        val |= SYSCFG_PMCR_ETH_REF_CLK_SEL;
                pr_debug("SYSCFG init : PHY_INTERFACE_MODE_RMII\n");
                break;
        case PHY_INTERFACE_MODE_RGMII:
+       case PHY_INTERFACE_MODE_RGMII_ID:
+       case PHY_INTERFACE_MODE_RGMII_RXID:
+       case PHY_INTERFACE_MODE_RGMII_TXID:
                val = SYSCFG_PMCR_ETH_SEL_RGMII;
-               if (dwmac->int_phyclk)
+               if (dwmac->eth_clk_sel_reg)
                        val |= SYSCFG_PMCR_ETH_CLK_SEL;
                pr_debug("SYSCFG init : PHY_INTERFACE_MODE_RGMII\n");
                break;
@@ -154,6 +211,11 @@ static int stm32mp1_set_mode(struct plat_stmmacenet_data *plat_dat)
                return -EINVAL;
        }
 
+       /* Need to update PMCCLRR (clear register) */
+       ret = regmap_write(dwmac->regmap, reg + SYSCFG_PMCCLRR_OFFSET,
+                          dwmac->ops->syscfg_eth_mask);
+
+       /* Update PMCSETR (set register) */
        return regmap_update_bits(dwmac->regmap, reg,
                                 dwmac->ops->syscfg_eth_mask, val);
 }
@@ -181,7 +243,7 @@ static int stm32mcu_set_mode(struct plat_stmmacenet_data *plat_dat)
        }
 
        return regmap_update_bits(dwmac->regmap, reg,
-                                dwmac->ops->syscfg_eth_mask, val);
+                                dwmac->ops->syscfg_eth_mask, val << 23);
 }
 
 static void stm32_dwmac_clk_disable(struct stm32_dwmac *dwmac)
@@ -237,22 +299,25 @@ static int stm32mp1_parse_data(struct stm32_dwmac *dwmac,
        struct device_node *np = dev->of_node;
        int err = 0;
 
-       dwmac->int_phyclk = of_property_read_bool(np, "st,int-phyclk");
+       /* Gigabit Ethernet 125MHz clock selection. */
+       dwmac->eth_clk_sel_reg = of_property_read_bool(np, "st,eth-clk-sel");
 
-       /* Check if internal clk from RCC selected */
-       if (dwmac->int_phyclk) {
-               /*  Get ETH_CLK clocks */
-               dwmac->clk_eth_ck = devm_clk_get(dev, "eth-ck");
-               if (IS_ERR(dwmac->clk_eth_ck)) {
-                       dev_err(dev, "No ETH CK clock provided...\n");
-                       return PTR_ERR(dwmac->clk_eth_ck);
-               }
+       /* Ethernet 50Mhz RMII clock selection */
+       dwmac->eth_ref_clk_sel_reg =
+               of_property_read_bool(np, "st,eth-ref-clk-sel");
+
+       /*  Get ETH_CLK clocks */
+       dwmac->clk_eth_ck = devm_clk_get(dev, "eth-ck");
+       if (IS_ERR(dwmac->clk_eth_ck)) {
+               dev_warn(dev, "No phy clock provided...\n");
+               dwmac->clk_eth_ck = NULL;
        }
 
        /*  Clock used for low power mode */
        dwmac->clk_ethstp = devm_clk_get(dev, "ethstp");
        if (IS_ERR(dwmac->clk_ethstp)) {
-               dev_err(dev, "No ETH peripheral clock provided for CStop mode ...\n");
+               dev_err(dev,
+                       "No ETH peripheral clock provided for CStop mode ...\n");
                return PTR_ERR(dwmac->clk_ethstp);
        }
 
@@ -268,7 +333,7 @@ static int stm32mp1_parse_data(struct stm32_dwmac *dwmac,
         */
        dwmac->irq_pwr_wakeup = platform_get_irq_byname(pdev,
                                                        "stm32_pwr_wakeup");
-       if (!dwmac->int_phyclk && dwmac->irq_pwr_wakeup >= 0) {
+       if (!dwmac->clk_eth_ck && dwmac->irq_pwr_wakeup >= 0) {
                err = device_init_wakeup(&pdev->dev, true);
                if (err) {
                        dev_err(&pdev->dev, "Failed to init wake up irq\n");
@@ -370,7 +435,7 @@ static int stm32mp1_suspend(struct stm32_dwmac *dwmac)
 
        clk_disable_unprepare(dwmac->clk_tx);
        clk_disable_unprepare(dwmac->syscfg_clk);
-       if (dwmac->int_phyclk)
+       if (dwmac->clk_eth_ck)
                clk_disable_unprepare(dwmac->clk_eth_ck);
 
        return ret;