This adds support for a popular low-cost 5GHz N based AP
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "ar9344_tplink_cpexxx-v1.dtsi"
+
+/ {
+ compatible = "tplink,wbs510-v1", "qca,ar9344";
+ model = "TP-Link WBS510 v1";
+};
+
+&led_link4 {
+ gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+};
tplink,cpe220-v3|\
tplink,cpe510-v1|\
tplink,wbs210-v2|\
+tplink,wbs510-v1|\
tplink,wbs510-v2)
ucidef_set_led_netdev "lan0" "LAN0" "tp-link:green:lan0" "eth1"
ucidef_set_led_switch "lan1" "LAN1" "tp-link:green:lan1" "switch0" "0x10"
tplink,cpe220-v3|\
tplink,cpe510-v1|\
tplink,wbs210-v2|\
+ tplink,wbs510-v1|\
tplink,wbs510-v2|\
ubnt,nanostation-m|\
ubnt,routerstation)
tplink,cpe220-v3|\
tplink,cpe510-v1|\
tplink,wbs210-v2|\
+tplink,wbs510-v1|\
tplink,wbs510-v2)
ucidef_add_gpio_switch "poe_passthrough" "PoE Passthrough" "20"
;;
endef
TARGET_DEVICES += tplink_wbs210-v2
+define Device/tplink_wbs510-v1
+ $(Device/tplink-loader-okli)
+ ATH_SOC := ar9344
+ IMAGE_SIZE := 7680k
+ DEVICE_MODEL := WBS510
+ DEVICE_VARIANT := v1
+ DEVICE_PACKAGES := rssileds
+ TPLINK_BOARD_ID := WBS510
+ SUPPORTED_DEVICES += wbs510
+endef
+TARGET_DEVICES += tplink_wbs510-v1
+
define Device/tplink_wbs510-v2
$(Device/tplink-loader-okli)
ATH_SOC := ar9344
"SupportList:\r\n"
"WBS510(TP-LINK|UN|N300-5):1.20\r\n"
"WBS510(TP-LINK|US|N300-5):1.20\r\n"
- "WBS510(TP-LINK|EU|N300-5):1.20\r\n",
+ "WBS510(TP-LINK|EU|N300-5):1.20\r\n"
+ "WBS510(TP-LINK|CA|N300-5):1.20\r\n",
.support_trail = '\xff',
.soft_ver = NULL,