mediatek: filogic: add support for Cudy M3000 v1

Hardware:
  SoC:     MT7981b
  RAM:     256 MB
  Flash:   128 MB SPI NAND
  Ethernet:
    1x 2.5Gbps (rtl8221b)
    1x 1Gbps (integrated phy)
  WiFi:    2x2 MT7981
  Buttons: Reset, WPS
  LED:     1x multicolor

Solder on UART:
  - remove rubber ring on the bottom
  - remove screws
  - pull up the cylinder, maybe help by push on an ethernet socket with a screwdriver
  - remove the (3) screws holding the board in the frame
  - remove the board from the frame to get to the screws for the silver, flat heat shield
  - remove the (3) screws holding the heat shield
  - solder UART pins to the back of the board
    - make sure to have the pins point out on side with the black, finned heat spread
    - the markings for the pins are going to be below the silver heat shield
    - Vcc is not needed

If you don't intend on using the UART outside of the installation process, you might not
want to solder:

  - carefully scrape off the thin layer of epoxy on the holes (not the copper)
  - place your pin header with the UART attached in the holes
  - the pins, starting with the one closest to the socket:
    - Vcc (not required)
    - GND
    - RX
    - TX
  - either wedge the header or hold it with your fingers so that the pins stay in contact with the board

Installation (UART):
  - attach an Ethernet cable to the 1Gbps port (black) on the router
  - hold the reset button while powering the router
  - press CTRL-C or wait for the timeout to get to the U-Boot prompt
  - prepare a TFTP server on the network to supply ..-initramfs-kernel.bin
  - use 'tftpboot' in the U-Boot shell to pull the image
  - boot the image using 'bootm'
  - push the ..-sysupgrade to the router using your preferred method
  - perform the upgrade with 'sysupgrade -n'

There is a recovery mechanism that involves fetching a file called 'recovery.bin' but that is not understood yet.

Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>

diff --git a/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface b/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface
index 9351ffd4924fe29540bf5cbd6b2aeb6e5c925960..6dfa52c291146183c67bc4b1813b48cd9bf0d7dc 100644 (file)
--- a/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface
+++ b/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface
@@ -1,10 +1,6 @@
 set_preinit_iface() {
        case $(board_name) in
-       smartrg,sdg-8622|\
-       smartrg,sdg-8632)
-               ip link set lan up
-               ifname=lan
-               ;;
+       cudy,m3000-v1|\
        cudy,tr3000-v1|\
        glinet,gl-mt3000)
                ip link set eth1 up
@@ -16,6 +12,11 @@ set_preinit_iface() {
                ip link set eth0 up
                ifname=eth0
                ;;
+       smartrg,sdg-8622|\
+       smartrg,sdg-8632)
+               ip link set lan up
+               ifname=lan
+               ;;
        xiaomi,mi-router-ax3000t|\
        xiaomi,mi-router-ax3000t-ubootmod|\
        xiaomi,mi-router-wr30u-stock|\

diff --git a/target/linux/mediatek/dts/mt7981b-cudy-m3000-v1.dts b/target/linux/mediatek/dts/mt7981b-cudy-m3000-v1.dts
new file mode 100644 (file)
index 0000000..e700d37
--- /dev/null
+++ b/target/linux/mediatek/dts/mt7981b-cudy-m3000-v1.dts
@@ -0,0 +1,214 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+/dts-v1/;
+
+#include "mt7981.dtsi"
+
+/ {
+       model = "Cudy M3000 v1";
+       compatible = "cudy,m3000-v1", "mediatek,mt7981-spim-snand-rfb";
+
+       aliases {
+               ethernet0 = &gmac0;
+               label-mac-device = &gmac0;
+               led-boot = &led_status;
+               led-failsafe = &led_status;
+               led-running = &led_status;
+               led-upgrade = &led_status;
+               serial0 = &uart0;
+       };
+
+       chosen {
+               stdout-path = "serial0:115200n8";
+       };
+
+       gpio-keys {
+               compatible = "gpio-keys";
+
+               reset {
+                       label = "reset";
+                       gpios = <&pio 1 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RESTART>;
+               };
+
+               wps {
+                       label = "wps";
+                       gpios = <&pio 0 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_WPS_BUTTON>;
+               };
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               led_status: internet-white {
+                       function = LED_FUNCTION_WAN_ONLINE;
+                       color = <LED_COLOR_ID_WHITE>;
+                       gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+               };
+
+               internet-red {
+                       function = LED_FUNCTION_WAN_ONLINE;
+                       color = <LED_COLOR_ID_RED>;
+                       gpios = <&pio 4 GPIO_ACTIVE_LOW>;
+               };
+
+               wan {
+                       function = LED_FUNCTION_WAN;
+                       color = <LED_COLOR_ID_GREEN>;
+                       gpios = <&pio 5 GPIO_ACTIVE_LOW>;
+               };
+
+               lan {
+                       function = LED_FUNCTION_LAN;
+                       color = <LED_COLOR_ID_GREEN>;
+                       gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+               };
+       };
+};
+
+&uart0 {
+       status = "okay";
+};
+
+&watchdog {
+       status = "okay";
+};
+
+&eth {
+       pinctrl-names = "default";
+       pinctrl-0 = <&mdio_pins>;
+
+       status = "okay";
+
+       gmac0: mac@0 {
+               compatible = "mediatek,eth-mac";
+               reg = <0>;
+               phy-mode = "2500base-x";
+               phy-handle = <&rtl8221b_phy>;
+
+               /* the MAC address assignment using nvmem-cells doesn't work, so it's done through 02_network */
+       };
+
+       gmac1: mac@1 {
+               compatible = "mediatek,eth-mac";
+               reg = <1>;
+               phy-mode = "gmii";
+               phy-handle = <&int_gbe_phy>;
+
+               nvmem-cell-names = "mac-address";
+               nvmem-cells = <&macaddr_bdinfo_de00 0>;
+       };
+};
+
+&mdio_bus {
+       rtl8221b_phy: ethernet-phy@1 {
+               compatible = "ethernet-phy-ieee802.3-c45";
+               reg = <1>;
+
+               reset-gpios = <&pio 39 GPIO_ACTIVE_LOW>;
+
+               interrupts = <38 IRQ_TYPE_LEVEL_LOW>;
+               reset-assert-us = <100000>;
+               reset-deassert-us = <100000>;
+       };
+};
+
+&spi0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&spi0_flash_pins>;
+
+       status = "okay";
+
+       spi_nand: spi_nand@0 {
+               compatible = "spi-nand";
+               #address-cells = <1>;
+               #size-cells = <1>;
+               reg = <0>;
+
+               spi-max-frequency = <52000000>;
+               spi-tx-buswidth = <4>;
+               spi-rx-buswidth = <4>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       mediatek,nmbm;
+                       mediatek,bmt-max-ratio = <1>;
+                       mediatek,bmt-max-reserved-blocks = <64>;
+
+                       partition@0 {
+                               label = "BL2";
+                               reg = <0x0000000 0x0100000>;
+                               read-only;
+                       };
+
+                       partition@100000 {
+                               label = "u-boot-env";
+                               reg = <0x0100000 0x0080000>;
+                       };
+
+                       factory: partition@180000 {
+                               label = "Factory";
+                               reg = <0x0180000 0x0200000>;
+                               read-only;
+                       };
+
+                       bdinfo: partition@380000 {
+                               label = "bdinfo";
+                               reg = <0x0380000 0x0040000>;
+                               read-only;
+
+                               nvmem-layout {
+                                       compatible = "fixed-layout";
+                                       #address-cells = <1>;
+                                       #size-cells = <1>;
+
+                                       macaddr_bdinfo_de00: macaddr@de00 {
+                                               #nvmem-cell-cells = <1>;
+                                               compatible = "mac-base";
+                                               reg = <0xde00 0x6>;
+                                       };
+                               };
+                       };
+
+                       partition@3c0000 {
+                               label = "FIP";
+                               reg = <0x03c0000 0x0200000>;
+                       };
+
+                       partition@5c0000 {
+                               label = "ubi";
+                               reg = <0x05c0000 0x4000000>;
+                       };
+               };
+       };
+};
+
+&pio {
+       spi0_flash_pins: spi0-pins {
+               mux {
+                       function = "spi";
+                       groups = "spi0", "spi0_wp_hold";
+               };
+
+               conf-pu {
+                       pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
+                       drive-strength = <MTK_DRIVE_8mA>;
+                       bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
+               };
+
+               conf-pd {
+                       pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
+                       drive-strength = <MTK_DRIVE_8mA>;
+                       bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
+               };
+       };
+};
+
+&wifi {
+       status = "okay";
+       mediatek,mtd-eeprom = <&factory 0x0>;
+};

diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
index 648ecb928964885419f717926ecda02ba0a5a23d..4de3cf044d145f86f98a6c5098797bf2f72b6257 100644 (file)
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
@@ -53,9 +53,7 @@ mediatek_setup_interfaces()
        comfast,cf-e393ax)
                ucidef_set_interfaces_lan_wan "lan1" eth1
                ;;
-       dlink,aquila-pro-ai-m30-a1)
-               ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" internet
-               ;;
+       cudy,m3000-v1|\
        cudy,tr3000-v1|\
        glinet,gl-mt2500|\
        glinet,gl-mt3000|\
@@ -64,6 +62,9 @@ mediatek_setup_interfaces()
        openembed,som7981)
                ucidef_set_interfaces_lan_wan eth1 eth0
                ;;
+       dlink,aquila-pro-ai-m30-a1)
+               ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" internet
+               ;;
        glinet,gl-mt6000|\
        tplink,tl-xdr4288|\
        tplink,tl-xdr6088)
@@ -135,6 +136,9 @@ mediatek_setup_macs()
                ;;
                esac
                ;;
+       cudy,m3000-v1)
+               wan_mac=$(macaddr_add $(cat /sys/class/net/eth1/address) 1)
+               ;;
        h3c,magic-nx30-pro)
                wan_mac=$(mtd_get_mac_ascii pdt_data_1 ethaddr)
                lan_mac=$(macaddr_add "$wan_mac" 1)

diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
index 75c3d25ed9a9ca9c52a364fe43030b9eefb3fcc2..e0e1e1f1fc24f4c4cbbc024b69b50cebf5872aff 100644 (file)
--- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
+++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
@@ -75,6 +75,7 @@ case "$board" in
                [ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress
                [ "$PHYNBR" = "1" ] && macaddr_setbit_la $(macaddr_add $addr 1) > /sys${DEVPATH}/macaddress
                ;;
+       cudy,m3000-v1|\
        cudy,wr3000-v1)
                addr=$(mtd_get_mac_binary bdinfo 0xde00)
                # Originally, phy0 is phy1 mac with LA bit set. However, this would conflict

diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk
index dbe027265a4ad8479f68f471d541d491341eb56f..79489558421b7c041761081bf8ca2ab582f8cae6 100644 (file)
--- a/target/linux/mediatek/image/filogic.mk
+++ b/target/linux/mediatek/image/filogic.mk
@@ -466,6 +466,28 @@ define Device/confiabits_mt7981
 endef
 TARGET_DEVICES += confiabits_mt7981
 
+define Device/cudy_m3000-v1
+  DEVICE_VENDOR := Cudy
+  DEVICE_MODEL := M3000
+  DEVICE_VARIANT := v1
+  DEVICE_DTS := mt7981b-cudy-m3000-v1
+  DEVICE_DTS_DIR := ../dts
+  SUPPORTED_DEVICES += R37
+  DEVICE_DTS_LOADADDR := 0x44000000
+  BLOCKSIZE := 128k
+  PAGESIZE := 2048
+  IMAGE_SIZE := 65536k
+  KERNEL_IN_UBI := 1
+  KERNEL := kernel-bin | lzma | \
+       fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
+  KERNEL_INITRAMFS := kernel-bin | lzma | \
+       fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
+  IMAGES := sysupgrade.bin
+  IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+  DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
+endef
+TARGET_DEVICES += cudy_m3000-v1
+
 define Device/cudy_re3000-v1
   DEVICE_VENDOR := Cudy
   DEVICE_MODEL := RE3000