This patch adds support for the Linksys EA7500 V1 router.
Specification:
- CPU: Qualcomm IPQ8064
- RAM: 256MB
- Flash: NAND 128MB
- WiFi: QCA9982 an+ac + QCA9983 bgn
- Ethernet: 5 GBE Ports (WAN+ 4xLAN) (QCA8337)
- USB: 1x USB 3.0 1x USB2.0
- Serial console: RJ-45 115200 8n1 (1V8 Voltage level)
- 2 Buttons
- 1 LED
Known issues:
- Some devices won't flash via web gui
Installation:
- Newer stock images doesn't allow to install custom firmware.
- Please downgrade software to 1.1.2 version. Official firmware:
https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.gpg.img
- Do it two times to downgrade all stored images.
- Apply factory image via web-gui.
Serial + TFTP method:
- downgrade to 1.1.2 two times
- connect ehternet and serial cable
- set ip address of tftp server to 192.168.1.254
- put openwrt factory image to tftp folder and rename it to macan.bin
- stop device while booting in u-boot
- run command: "run flashimg"
- run command: "setenv boot_part 1"
- run command "saveenv"
- reset
Back to stock:
- Please use old non-gpg image like this 1.1.2:
https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.img
- ssh to router and copy image to tmp
- use sysupgrade -n -F
Tested by github users: @jack338c and @grzesiczek1
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[removed i2c4_pins, mdio0_pins, nand_pins, rgmii2_pins from DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
}
case "$board" in
+linksys,ea7500-v1 |\
linksys,ea8500)
ubootenv_add_uci_config "/dev/mtd10" "0x0" "0x20000" "0x20000"
;;
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3u@eth1" "6:wan" "4u@eth0"
;;
+linksys,ea7500-v1)
+ hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
+ ucidef_add_switch "switch0" \
+ "2:lan:1" "3:lan:2" "4:lan:3" "5:lan:4" "6@eth1" "1:wan" "0@eth0"
+ ucidef_set_interface_macaddr "lan" "$hw_mac_addr"
+ ucidef_set_interface_macaddr "wan" "$hw_mac_addr"
+ ;;
linksys,ea8500)
hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
ucidef_add_switch "switch0" \
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(mtd_get_mac_binary ART 0x1e)
;;
+ linksys,ea7500-v1 |\
linksys,ea8500)
caldata_extract "art" 0x1000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii devinfo hw_mac_addr) +1)
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(mtd_get_mac_binary ART 0x18)
;;
+ linksys,ea7500-v1 |\
linksys,ea8500)
caldata_extract "art" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii devinfo hw_mac_addr) +2)
boot() {
case $(board_name) in
+ linksys,ea7500-v1 |\
linksys,ea8500)
mtd resetbc s_env || true
;;
zyxel,nbg6817)
zyxel_do_upgrade "$1"
;;
+ linksys,ea7500-v1 |\
linksys,ea8500)
platform_do_upgrade_linksys "$1"
;;
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+#include "qcom-ipq8064-v2.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Linksys EA7500 V1 WiFi Router";
+ compatible = "linksys,ea7500-v1", "qcom,ipq8064";
+
+ memory@0 {
+ reg = <0x42000000 0xe000000>;
+ device_type = "memory";
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ rsvd@41200000 {
+ reg = <0x41200000 0x300000>;
+ no-map;
+ };
+ };
+
+ aliases {
+ serial0 = &gsbi4_serial;
+
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ chosen {
+ bootargs = "console=ttyMSM0,115200n8";
+ stdout-path = "serial0:115200n8";
+ append-rootblock = "ubi.mtd="; /* append to bootargs adding the root deviceblock nbr from bootloader */
+ find-rootblock = "ubi.mtd="; /* look for root deviceblock nbr in this bootarg */
+ };
+
+ keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&button_pins>;
+ pinctrl-names = "default";
+
+ reset {
+ label = "reset";
+ gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&led_pins>;
+ pinctrl-names = "default";
+
+ led_power: power {
+ label = "ea7500-v1:white:power";
+ gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ };
+ };
+};
+
+&qcom_pinmux {
+ button_pins: button_pins {
+ mux {
+ pins = "gpio65", "gpio68";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ led_pins: led_pins {
+ mux {
+ pins = "gpio6";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+};
+
+&gsbi4 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "okay";
+ serial@16340000 {
+ status = "okay";
+ };
+ /*
+ * The i2c device on gsbi4 should not be enabled.
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
+ * RPM usage. Turning this on in kernel manifests as
+ * i2c failure for the RPM.
+ */
+};
+
+&usb3_0 {
+ status = "okay";
+};
+
+&usb3_1 {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+ force_gen1 = <1>;
+};
+
+&pcie1 {
+ status = "okay";
+};
+
+&pcie2 {
+ status = "okay";
+};
+
+&nand_controller {
+ status = "okay";
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ nand@0 {
+ reg = <0>;
+ compatible = "qcom,nandcs";
+
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "SBL1";
+ reg = <0x0000000 0x0040000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "MIBIB";
+ reg = <0x0040000 0x0140000>;
+ read-only;
+ };
+
+ partition@180000 {
+ label = "SBL2";
+ reg = <0x0180000 0x0140000>;
+ read-only;
+ };
+
+ partition@2c0000 {
+ label = "SBL3";
+ reg = <0x02c0000 0x0280000>;
+ read-only;
+ };
+
+ partition@540000 {
+ label = "DDRCONFIG";
+ reg = <0x0540000 0x0120000>;
+ read-only;
+ };
+
+ partition@660000 {
+ label = "SSD";
+ reg = <0x0660000 0x0120000>;
+ read-only;
+ };
+
+ partition@780000 {
+ label = "TZ";
+ reg = <0x0780000 0x0280000>;
+ read-only;
+ };
+
+ partition@a00000 {
+ label = "RPM";
+ reg = <0x0a00000 0x0280000>;
+ read-only;
+ };
+
+ art: partition@c80000 {
+ label = "art";
+ reg = <0x0c80000 0x0140000>;
+ read-only;
+ };
+
+ partition@dc0000 {
+ label = "APPSBL";
+ reg = <0x0dc0000 0x0100000>;
+ read-only;
+ };
+
+ partition@ec0000 {
+ label = "u_env";
+ reg = <0x0ec0000 0x0040000>;
+ };
+
+ partition@f00000 {
+ label = "s_env";
+ reg = <0x0f00000 0x0040000>;
+ };
+
+ partition@f40000 {
+ label = "devinfo";
+ reg = <0x0f40000 0x0040000>;
+ };
+
+ partition@f80000 {
+ label = "kernel1";
+ reg = <0x0f80000 0x2800000>; /* 3 MB spill to rootfs*/
+ };
+
+ partition@1280000 {
+ label = "rootfs1";
+ reg = <0x1280000 0x2500000>;
+ };
+
+ partition@3780000 {
+ label = "kernel2";
+ reg = <0x3780000 0x2800000>;
+ };
+
+ partition@3a80000 {
+ label = "rootfs2";
+ reg = <0x3a80000 0x2500000>;
+ };
+
+ partition@5f80000 {
+ label = "sysdiag";
+ reg = <0x5f80000 0x100000>;
+ };
+
+ partition@6080000 {
+ label = "syscfg";
+ reg = <0x6080000 0x1f80000>;
+ };
+ };
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ pinctrl-0 = <&mdio0_pins>;
+ pinctrl-names = "default";
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ qca,ar8327-initvals = <
+ 0x00004 0x7600000 /* PAD0_MODE */
+ 0x00008 0x1000000 /* PAD5_MODE */
+ 0x0000c 0x80 /* PAD6_MODE */
+ 0x00010 0x2613a0 /* PWS_REG */
+ 0x000e4 0x6a545 /* MAC_POWER_SEL */
+ 0x000e0 0xc74164de /* SGMII_CTRL */
+ 0x0007c 0x4e /* PORT0_STATUS */
+ 0x00094 0x4e /* PORT6_STATUS */
+ >;
+ };
+};
+
+&gmac1 {
+ status = "okay";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&gmac2 {
+ status = "okay";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&adm_dma {
+ status = "okay";
+};
endef
TARGET_DEVICES += compex_wpq864
+define Device/linksys_ea7500-v1
+ $(call Device/LegacyImage)
+ DEVICE_VENDOR := Linksys
+ DEVICE_MODEL := EA7500
+ DEVICE_VARIANT := v1
+ SOC := qcom-ipq8064
+ PAGESIZE := 2048
+ BLOCKSIZE := 128k
+ KERNEL_SIZE := 3072k
+ KERNEL = kernel-bin | append-dtb | uImage none | append-uImage-fakehdr filesystem
+ UBINIZE_OPTS := -E 5
+ IMAGES := factory.bin sysupgrade.bin
+ IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | pad-to $$$$(PAGESIZE)
+ DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
+endef
+TARGET_DEVICES += linksys_ea7500-v1
+
define Device/linksys_ea8500
$(call Device/LegacyImage)
DEVICE_VENDOR := Linksys
#else
#define do_extend_cmdline 0
#endif
-@@ -67,6 +69,59 @@ static uint32_t get_cell_size(const void
+@@ -67,6 +69,80 @@ static uint32_t get_cell_size(const void
return cell_size;
}
+#if defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE)
++/**
++ * taken from arch/x86/boot/string.c
++ * local_strstr - Find the first substring in a %NUL terminated string
++ * @s1: The string to be searched
++ * @s2: The string to search for
++ */
++static char *local_strstr(const char *s1, const char *s2)
++{
++ size_t l1, l2;
++
++ l2 = strlen(s2);
++ if (!l2)
++ return (char *)s1;
++ l1 = strlen(s1);
++ while (l1 >= l2) {
++ l1--;
++ if (!memcmp(s1, s2, l2))
++ return (char *)s1;
++ s1++;
++ }
++ return NULL;
++}
+
+static char *append_rootblock(char *dest, const char *str, int len, void *fdt)
+{
-+ char *ptr, *end;
++ char *ptr, *end, *tmp;
+ char *root="root=";
++ char *find_rootblock;
+ int i, l;
+ const char *rootblock;
+
-+ //ARM doesn't have __HAVE_ARCH_STRSTR, so search manually
-+ ptr = str - 1;
-+
-+ do {
-+ //first find an 'r' at the begining or after a space
-+ do {
-+ ptr++;
-+ ptr = strchr(ptr, 'r');
-+ if(!ptr) return dest;
++ find_rootblock = getprop(fdt, "/chosen", "find-rootblock", &l);
++ if(!find_rootblock)
++ find_rootblock = root;
+
-+ } while (ptr != str && *(ptr-1) != ' ');
++ //ARM doesn't have __HAVE_ARCH_STRSTR, so it was copied from x86
++ ptr = local_strstr(str, find_rootblock);
+
-+ //then check for the rest
-+ for(i = 1; i <= 4; i++)
-+ if(*(ptr+i) != *(root+i)) break;
-+
-+ } while (i != 5);
++ if(!ptr)
++ return dest;
+
+ end = strchr(ptr, ' ');
+ end = end ? (end - 1) : (strchr(ptr, 0) - 1);
+
-+ //find partition number (assumes format root=/dev/mtdXX | /dev/mtdblockXX | yy:XX )
++ // Some boards ubi.mtd=XX,ZZZZ, so let's check for '," too.
++ tmp = strchr(ptr, ',');
++
++ if(tmp)
++ end = end < tmp ? end : tmp - 1;
++
++ //find partition number (assumes format root=/dev/mtdXX | /dev/mtdblockXX | yy:XX | ubi.mtd=XX,ZZZZ )
+ for( i = 0; end >= ptr && *end >= '0' && *end <= '9'; end--, i++);
+ ptr = end + 1;
+
static void merge_fdt_bootargs(void *fdt, const char *fdt_cmdline)
{
char cmdline[COMMAND_LINE_SIZE];
-@@ -86,12 +141,21 @@ static void merge_fdt_bootargs(void *fdt
+@@ -86,12 +162,21 @@ static void merge_fdt_bootargs(void *fdt
/* and append the ATAG_CMDLINE */
if (fdt_cmdline) {
}
*ptr = '\0';
-@@ -166,7 +230,9 @@ int atags_to_fdt(void *atag_list, void *
+@@ -166,7 +251,9 @@ int atags_to_fdt(void *atag_list, void *
else
setprop_string(fdt, "/chosen", "bootargs",
atag->u.cmdline.cmdline);
if (memcount >= sizeof(mem_reg_property)/4)
continue;
if (!atag->u.mem.size)
-@@ -210,6 +276,10 @@ int atags_to_fdt(void *atag_list, void *
+@@ -210,6 +297,10 @@ int atags_to_fdt(void *atag_list, void *
setprop(fdt, "/memory", "reg", mem_reg_property,
4 * memcount * memsize);
}
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -843,6 +843,18 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -843,6 +843,19 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-ipq4019-ap.dk07.1-c1.dtb \
qcom-ipq4019-ap.dk07.1-c2.dtb \
qcom-ipq8064-ap148.dtb \
+ qcom-ipq8064-d7800.dtb \
+ qcom-ipq8064-db149.dtb \
+ qcom-ipq8064-ap161.dtb \
++ qcom-ipq8064-ea7500-v1.dtb \
+ qcom-ipq8064-ea8500.dtb \
+ qcom-ipq8064-r7500.dtb \
+ qcom-ipq8064-r7500v2.dtb \
projects / openwrt / staging / zorun.git / commitdiff