+++ /dev/null
-#!/bin/sh
-#
-# Copyright (C) 2014-2016 OpenWrt.org
-# Copyright (C) 2016 LEDE-Project.org
-#
-
-. /lib/functions/uci-defaults.sh
-
-board_config_update
-
-board=$(board_name)
-
-case "$board" in
-linksys,caiman)
- ucidef_set_led_netdev "wan" "WAN" "pca963x:caiman:white:wan" "eth1"
- ucidef_set_led_usbport "usb1" "USB 1" "pca963x:caiman:white:usb2" "usb1-port1"
- ucidef_set_led_usbport "usb2" "USB 2" "pca963x:caiman:white:usb3_1" "usb2-port1" "usb3-port1"
- ucidef_set_led_usbport "usb2_ss" "USB 2 SS" "pca963x:caiman:white:usb3_2" "usb3-port1"
- ;;
-linksys,cobra)
- ucidef_set_led_netdev "wan" "WAN" "pca963x:cobra:white:wan" "eth1"
- ucidef_set_led_usbport "usb1" "USB 1" "pca963x:cobra:white:usb2" "usb1-port1"
- ucidef_set_led_usbport "usb2" "USB 2" "pca963x:cobra:white:usb3_1" "usb2-port1" "usb3-port1"
- ucidef_set_led_usbport "usb2_ss" "USB 2 SS" "pca963x:cobra:white:usb3_2" "usb3-port1"
- ;;
-linksys,mamba)
- ucidef_set_led_netdev "wan" "WAN" "mamba:white:wan" "eth1"
- ucidef_set_led_usbport "usb1" "USB 1" "mamba:white:usb2" "usb1-port1"
- ucidef_set_led_usbport "usb2" "USB 2" "mamba:white:usb3_1" "usb2-port1" "usb3-port1"
- ucidef_set_led_usbport "usb2_ss" "USB 2 SS" "mamba:white:usb3_2" "usb3-port2"
- ;;
-linksys,rango)
- ucidef_set_led_netdev "wan" "WAN" "pca963x:rango:white:wan" "eth1"
- ucidef_set_led_usbport "usb1" "USB 1" "pca963x:rango:white:usb2" "usb1-port1"
- ucidef_set_led_usbport "usb2" "USB 2" "pca963x:rango:white:usb3_1" "usb2-port1" "usb3-port1"
- ucidef_set_led_usbport "usb2_ss" "USB 2 SS" "pca963x:rango:white:usb3_2" "usb3-port1"
- ;;
-linksys,shelby)
- ucidef_set_led_netdev "wan" "WAN" "pca963x:shelby:white:wan" "eth1"
- ucidef_set_led_usbport "usb1" "USB 1" "pca963x:shelby:white:usb2" "usb1-port1"
- ucidef_set_led_usbport "usb2" "USB 2" "pca963x:shelby:white:usb3_1" "usb2-port1" "usb3-port1"
- ucidef_set_led_usbport "usb2_ss" "USB 2 SS" "pca963x:shelby:white:usb3_2" "usb3-port1"
- ;;
-linksys,venom)
- ucidef_set_led_netdev "wan" "WAN" "pca963x:venom:blue:wan" "eth1"
- ucidef_set_led_usbport "usb1" "USB 1" "pca963x:venom:blue:usb2" "usb1-port1"
- ucidef_set_led_usbport "usb2" "USB 2" "pca963x:venom:blue:usb3_1" "usb2-port1" "usb3-port1"
- ucidef_set_led_usbport "usb2_ss" "USB 2 SS" "pca963x:venom:blue:usb3_2" "usb3-port1"
- ;;
-
-esac
-
-board_config_flush
-
-exit 0
+++ /dev/null
-#!/bin/sh
-#
-# Copyright (C) 2014-2016 OpenWrt.org
-# Copyright (C) 2016 LEDE-Project.org
-#
-
-. /lib/functions/uci-defaults.sh
-
-board_config_update
-
-board=$(board_name)
-
-case "$board" in
-cznic,turris-omnia)
- ucidef_set_interface_lan "lan0 lan1 lan2 lan3 lan4"
- ucidef_set_interface_wan "eth2"
- ;;
-globalscale,espressobin|\
-globalscale,espressobin-emmc|\
-globalscale,espressobin-v7|\
-globalscale,espressobin-v7-emmc)
- ucidef_set_interfaces_lan_wan "lan0 lan1" "wan"
- ;;
-linksys,caiman|\
-linksys,cobra|\
-linksys,mamba|\
-linksys,rango|\
-linksys,shelby|\
-linksys,venom)
- ucidef_set_interfaces_lan_wan "eth0.1" "eth1.2"
- ucidef_add_switch "switch0" \
- "0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "5@eth0" "4:wan" "6@eth1"
- ;;
-marvell,a385-db-ap)
- ucidef_set_interfaces_lan_wan "eth0 eth1" "eth2"
- ;;
-marvell,armada8040-mcbin)
- ucidef_set_interfaces_lan_wan "eth0 eth1 eth3" "eth2"
- ;;
-marvell,armada8040-db)
- ucidef_set_interfaces_lan_wan "eth0 eth2 eth3" "eth1"
- ;;
-marvell,armada7040-db)
- ucidef_set_interfaces_lan_wan "eth0 eth2" "eth1"
- ;;
-marvell,armada-3720-db)
- ucidef_set_interfaces_lan_wan "eth1" "eth0"
- ;;
-marvell,axp-gp)
- ucidef_set_interface_lan "eth0 eth1 eth2 eth3"
- ;;
-methode,udpu)
- ucidef_set_interfaces_lan_wan "eth1" "eth0"
- ;;
-solidrun,clearfog-a1|solidrun,clearfog-pro-a1)
- # eth0 is standalone ethernet
- # eth1 is switch
- # eth2 is SFP
- ucidef_set_interfaces_lan_wan "eth1" "eth0 eth2"
-
- # switch port 5 is connected to eth1
- ucidef_add_switch "switch0" \
- "0:lan:5" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5u@eth1" "6:lan:6"
- ;;
-solidrun,clearfog-base-a1)
- # eth0 is standalone ethernet
- # eth1 is standalone ethernet
- # eth2 is SFP
- ucidef_set_interfaces_lan_wan "eth1" "eth0 eth2"
- ;;
-*)
- ucidef_set_interface_lan "eth0"
- ;;
-esac
-
-board_config_flush
-
-exit 0
+++ /dev/null
-#!/bin/sh /etc/rc.common
-
-START=99
-
-boot() {
- case $(board_name) in
- linksys,caiman |\
- linksys,cobra |\
- linksys,mamba |\
- linksys,rango |\
- linksys,shelby |\
- linksys,venom)
- mtd resetbc s_env || true
- ;;
- esac
-}
+++ /dev/null
-#!/bin/sh
-#
-# Copyright (C) 2015 OpenWrt.org
-#
-
-[ ! -e /etc/config/wireless ] && exit 0
-
-. /lib/functions.sh
-. /lib/functions/system.sh
-
-board=$(board_name)
-
-case "$board" in
-linksys,caiman|linksys,cobra|linksys,mamba|linksys,shelby|linksys,venom)
- SKU=$(strings /dev/mtd3|sed -ne 's/^cert_region=//p')
- WIFIMAC2G=$(macaddr_add $(cat /sys/class/net/eth0/address) +1)
- WIFIMAC5G=$(macaddr_add $WIFIMAC2G +1)
- case "$SKU" in
- AP)
- REGD=CN
- ;;
- AU)
- REGD=AU
- ;;
- CA)
- REGD=CA
- ;;
- EU)
- REGD=DE
- ;;
- US)
- REGD=US
- ;;
- esac
-
- case "$board" in
- linksys,mamba)
- WIFIMAC0=$WIFIMAC2G
- WIFIMAC1=$WIFIMAC5G
- ;;
- *)
- WIFIMAC0=$WIFIMAC5G
- WIFIMAC1=$WIFIMAC2G
- ;;
- esac
-
- uci get wireless.radio0.country || uci set wireless.radio0.country=$REGD
- uci get wireless.@wifi-iface[0].macaddr || uci set wireless.@wifi-iface[0].macaddr=$WIFIMAC0
- uci get wireless.radio1.country || uci set wireless.radio1.country=$REGD
- uci get wireless.@wifi-iface[1].macaddr || uci set wireless.@wifi-iface[1].macaddr=$WIFIMAC1
- ;;
-esac
-
-uci commit wireless
-
-exit 0
+++ /dev/null
-#!/bin/sh
-#
-# Copyright (C) 2017 LEDE-Project.org
-#
-
-. /lib/functions.sh
-
-board=$(board_name)
-
-case "$board" in
-linksys,mamba)
- # Set fan script execution in crontab
- grep -s -q fan_ctrl.sh /etc/crontabs/root && exit 0
-
- echo "# mamba fan script runs every 5 minutes" >> /etc/crontabs/root
- echo "*/5 * * * * /sbin/fan_ctrl.sh" >> /etc/crontabs/root
-
- # Execute one time after initial flash (instead of waiting 5 min for cron)
- /sbin/fan_ctrl.sh
- ;;
-esac
-
-exit 0
+++ /dev/null
-#
-# Copyright (C) 2014-2015 OpenWrt.org
-# Copyright (C) 2016 LEDE-Project.org
-#
-
-preinit_set_mac_address() {
- local mac
-
- . /lib/functions.sh
-
- case $(board_name) in
- linksys,caiman|linksys,cobra|linksys,rango|linksys,shelby|linksys,venom)
- # rename interfaces back to the way they were with 4.4
- case "$(readlink /sys/class/net/eth0)" in
- *f1070000*)
- ip link set eth0 name tmp0
- ip link set eth1 name eth0
- ip link set tmp0 name eth1
- ;;
- esac
-
- mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
- mac_wan=$(macaddr_setbit_la "$mac")
- ip link set dev eth0 address $mac 2>/dev/null
- ip link set dev eth1 address $mac_wan 2>/dev/null
- ;;
- linksys,mamba)
- mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
- ip link set dev eth0 address $mac 2>/dev/null
- ip link set dev eth1 address $mac 2>/dev/null
- ;;
- marvell,a385-db-ap|solidrun,clearfog*a1)
- # rename interfaces back to the way they were with 4.4
- case "$(readlink /sys/class/net/eth0)" in
- *f1070000*)
- ip link set eth0 name tmp0
- ip link set eth1 name eth0
- ip link set eth2 name eth1
- ip link set tmp0 name eth2
- ;;
- esac
- ;;
- esac
-}
-
-boot_hook_add preinit_main preinit_set_mac_address
+++ /dev/null
-#
-# Copyright (C) 2014-2016 OpenWrt.org
-# Copyright (C) 2016 LEDE-Project.org
-#
-
-preinit_mount_syscfg() {
- . /lib/functions.sh
- . /lib/upgrade/common.sh
-
- case $(board_name) in
- linksys,caiman|linksys,cobra|linksys,mamba|linksys,rango|linksys,shelby|linksys,venom)
- needs_recovery=0
- syscfg_part=$(grep syscfg /proc/mtd |cut -c4)
- ubiattach -m $syscfg_part || needs_recovery=1
- if [ $needs_recovery -eq 1 ]
- then
- echo "ubifs syscfg partition is damaged, reformatting"
- ubidetach -m $syscfg_part
- ubiformat -y -O 2048 -q /dev/mtd$syscfg_part
- ubiattach -m $syscfg_part
- ubimkvol /dev/ubi1 -n 0 -N syscfg -t dynamic --maxavsize
- fi
- mkdir /tmp/syscfg
- mount -t ubifs ubi1:syscfg /tmp/syscfg
- [ -f "/tmp/syscfg/$BACKUP_FILE" ] && {
- echo "- config restore -"
- cd /
- mv "/tmp/syscfg/$BACKUP_FILE" /tmp
- tar xzf "/tmp/$BACKUP_FILE"
- rm -f "/tmp/$BACKUP_FILE"
- sync
- }
- ;;
- esac
-}
-
-boot_hook_add preinit_main preinit_mount_syscfg
+++ /dev/null
-#
-# Copyright (C) 2014-2019 OpenWrt.org
-# Copyright (C) 2016 LEDE-Project.org
-#
-
-preinit_mount_udpu() {
- . /lib/functions.sh
- . /lib/upgrade/common.sh
-
- case $(board_name) in
- methode,udpu)
- # Check which device is detected
- [ -b "/dev/mmcblk0" ] && mmcdev="/dev/mmcblk0" || mmcdev="/dev/mmcblk1"
-
- if [ -b "${mmcdev}p4" ]; then
- mkdir /misc
- mount -t f2fs ${mmcdev}p4 /misc
- [ -f "/misc/$BACKUP_FILE" ] && {
- echo "- Restoring configuration files -"
- tar xzf "/misc/$BACKUP_FILE" -C /
- rm -f "/misc/$BACKUP_FILE"
- sync
- }
- [ -f "/misc/firmware/recovery.itb" ] && {
- echo "- Updating /recovery partition -"
- mkfs.ext4 -q ${mmcdev}p2 | echo y &> /dev/null
- mkdir -p /tmp/recovery
- mount ${mmcdev}p2 /tmp/recovery
- cp /misc/firmware/recovery.itb /tmp/recovery
- [ -f "/misc/firmware/boot.scr" ] && \
- cp /misc/firmware/boot.scr /tmp/recovery
- sync
- umount /tmp/recovery
- rm -rf /tmp/recovery
-
- # Replace previous backup with the new one
- [ -d "/misc/firmware_old" ] && rm -rf /misc/firmware_old
- [ -d "/misc/firmware" ] && mv /misc/firmware /misc/firmware_old
- }
- fi
-
- # Legacy support - if rootfs was booted, instruct u-boot to keep the current root dev
- [ "$(df | grep /dev/root)" ] && fw_setenv root_ok '2'
- ;;
- esac
-}
-
-boot_hook_add preinit_main preinit_mount_udpu
+++ /dev/null
-#
-# Copyright (C) 2014-2015 OpenWrt.org
-#
-
-linksys_get_target_firmware() {
-
- local cur_boot_part mtd_ubi0
-
- cur_boot_part=$(/usr/sbin/fw_printenv -n boot_part)
- if [ -z "${cur_boot_part}" ] ; then
- mtd_ubi0=$(cat /sys/devices/virtual/ubi/ubi0/mtd_num)
- case $(egrep ^mtd${mtd_ubi0}: /proc/mtd | cut -d '"' -f 2) in
- kernel1|rootfs1)
- cur_boot_part=1
- ;;
- kernel2|rootfs2)
- cur_boot_part=2
- ;;
- esac
- >&2 printf "Current boot_part='%s' selected from ubi0/mtd_num='%s'" \
- "${cur_boot_part}" "${mtd_ubi0}"
- fi
-
- case $cur_boot_part in
- 1)
- fw_setenv -s - <<-EOF
- boot_part 2
- bootcmd "run altnandboot"
- EOF
- printf "kernel2"
- return
- ;;
- 2)
- fw_setenv -s - <<-EOF
- boot_part 1
- bootcmd "run nandboot"
- EOF
- printf "kernel1"
- return
- ;;
- *)
- return
- ;;
- esac
-}
-
-linksys_get_root_magic() {
- (get_image "$@" | dd skip=786432 bs=4 count=1 | hexdump -v -n 4 -e '1/1 "%02x"') 2>/dev/null
-}
-
-platform_do_upgrade_linksys() {
- local magic_long="$(get_magic_long "$1")"
-
- mkdir -p /var/lock
- local part_label="$(linksys_get_target_firmware)"
- touch /var/lock/fw_printenv.lock
-
- if [ ! -n "$part_label" ]
- then
- echo "cannot find target partition"
- exit 1
- fi
-
- local target_mtd=$(find_mtd_part $part_label)
-
- [ "$magic_long" = "73797375" ] && {
- CI_KERNPART="$part_label"
- if [ "$part_label" = "kernel1" ]
- then
- CI_UBIPART="rootfs1"
- else
- CI_UBIPART="rootfs2"
- fi
-
- nand_upgrade_tar "$1"
- }
- [ "$magic_long" = "27051956" -o "$magic_long" = "0000a0e1" ] && {
- # check firmwares' rootfs types
- local target_mtd=$(find_mtd_part $part_label)
- local oldroot="$(linksys_get_root_magic $target_mtd)"
- local newroot="$(linksys_get_root_magic "$1")"
-
- if [ "$newroot" = "55424923" -a "$oldroot" = "55424923" ]
- # we're upgrading from a firmware with UBI to one with UBI
- then
- # erase everything to be safe
- mtd erase $part_label
- get_image "$1" | mtd -n write - $part_label
- else
- get_image "$1" | mtd write - $part_label
- fi
- }
-}
-
-platform_copy_config_linksys() {
- cp -f "$UPGRADE_BACKUP" "/tmp/syscfg/$BACKUP_FILE"
- sync
-}
+++ /dev/null
-#
-# Copyright (C) 2014-2016 OpenWrt.org
-# Copyright (C) 2016 LEDE-Project.org
-#
-
-RAMFS_COPY_BIN='fw_printenv fw_setenv'
-RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
-REQUIRE_IMAGE_METADATA=1
-
-platform_check_image() {
- case "$(board_name)" in
- cznic,turris-omnia|globalscale,espressobin|globalscale,espressobin-emmc|globalscale,espressobin-v7|globalscale,espressobin-v7-emmc|\
- marvell,armada8040-mcbin|solidrun,clearfog-base-a1|solidrun,clearfog-pro-a1)
- platform_check_image_sdcard "$1"
- ;;
- *)
- return 0
- ;;
- esac
-}
-
-platform_do_upgrade() {
- case "$(board_name)" in
- linksys,caiman|linksys,cobra|linksys,mamba|linksys,rango|linksys,shelby|linksys,venom)
- platform_do_upgrade_linksys "$1"
- ;;
- cznic,turris-omnia|globalscale,espressobin|globalscale,espressobin-emmc|globalscale,espressobin-v7|globalscale,espressobin-v7-emmc|\
- marvell,armada8040-mcbin|solidrun,clearfog-base-a1|solidrun,clearfog-pro-a1)
- platform_do_upgrade_sdcard "$1"
- ;;
- methode,udpu)
- platform_do_upgrade_uDPU "$1"
- ;;
- *)
- default_do_upgrade "$1"
- ;;
- esac
-}
-platform_copy_config() {
- case "$(board_name)" in
- linksys,caiman|linksys,cobra|linksys,mamba|linksys,rango|linksys,shelby|linksys,venom)
- platform_copy_config_linksys
- ;;
- cznic,turris-omnia|globalscale,espressobin|globalscale,espressobin-emmc|globalscale,espressobin-v7|globalscale,espressobin-v7-emmc|\
- marvell,armada8040-mcbin|solidrun,clearfog-base-a1|solidrun,clearfog-pro-a1)
- platform_copy_config_sdcard
- ;;
- methode,udpu)
- platform_copy_config_uDPU
- ;;
- esac
-}
+++ /dev/null
-udpu_check_emmc() {
-# uDPU uses combined ext4 and f2fs partitions.
-# partition layout:
-# 1. boot (ext4)
-# 2. recovery (ext4)
-# 3. rootfs (f2fs)
-# 4. misc (f2fs)
-
- # Check which device is available, depending on the board revision
- if [ -b "/dev/mmcblk1" ]; then
- emmc_dev=/dev/mmcblk1
- elif [ -b "/dev/mmcblk0" ]; then
- emmc_dev=/dev/mmcblk0
- else
- echo "Cannot detect eMMC flash, aborting.."
- exit 1
- fi
-}
-
-udpu_part_prep() {
- if [ "$(grep $1 /proc/mounts)" ]; then
- mounted_part="$(grep $1 /proc/mounts | awk '{print $2}' | head -1)"
- umount $mounted_part
- [ "$(grep -wo $mounted_part /proc/mounts)" ] && umount -l $mounted_part
- fi
-}
-
-udpu_do_part_check() {
- local emmc_parts="1 2 3 4"
- local part_valid="1"
-
- # Check if the block devices exist
- for num in ${emmc_parts}; do
- [[ ! -b ${emmc_dev}p${num} ]] && part_valid="0"
- done
-
- # If partitions are missing create a new partition table
- if [ "$part_valid" != "1" ]; then
- printf "Invalid partition table, creating a new one\n"
- printf "o\nn\np\n1\n\n+256M\nn\np\n2\n\n+256M\nn\np\n3\n\n+1536M\nn\np\n\n\nw\n" | fdisk -W always $emmc_dev > /dev/null 2>&1
-
- # Format the /misc part right away as we will need it for the firmware
- printf "Formating /misc partition, this make take a while..\n"
- udpu_part_prep ${emmc_dev}p4
- mkfs.f2fs -q -l misc ${emmc_dev}p4
- [ $? -eq 0 ] && printf "/misc partition formated successfully\n" || printf "/misc partition formatting failed\n"
-
- udpu_do_initial_setup
- else
- printf "Partition table looks ok\n"
- fi
-}
-
-udpu_do_misc_prep() {
- if [ ! "$(grep -wo /misc /proc/mounts)" ]; then
- mkdir -p /misc
- mount ${emmc_dev}p4 /misc
-
- # If the mount fails, try to reformat partition
- # Leaving possiblity for multiple iterations
- if [ $? -ne 0 ]; then
- printf "Error while mounting /misc, trying to reformat..\n"
-
- format_count=0
- while [ "$format_count" -lt "1" ]; do
- udpu_part_prep ${emmc_dev}p4
- mkfs.f2fs -q -l misc ${emmc_dev}p4
- mount ${emmc_dev}p4 /misc
- if [ $? -ne 0 ]; then
- umount -l /misc
- printf "Failed while mounting /misc\n"
- format_count=$((format_count +1))
- else
- printf "Mounted /misc successfully\n"
- break
- fi
- done
- fi
- fi
-}
-
-udpu_do_initial_setup() {
- # Prepare /recovery parition
- udpu_part_prep ${emmc_dev}p2
- mkfs.ext4 -q ${emmc_dev}p2 | echo y &> /dev/null
-
- # Prepare /boot partition
- udpu_part_prep ${emmc_dev}p1
- mkfs.ext4 -q ${emmc_dev}p1 | echo y &> /dev/null
-
- # Prepare /root partition
- printf "Formating /root partition, this may take a while..\n"
- udpu_part_prep ${emmc_dev}p3
- mkfs.f2fs -q -l rootfs ${emmc_dev}p3
- [ $? -eq 0 ] && printf "/root partition reformated\n"
-}
-
-udpu_do_regular_upgrade() {
- # Clean /boot partition - mfks.ext4 is not available in chroot
- [ "$(grep -wo /boot /proc/mounts)" ] && umount /boot
- mkdir -p /tmp/boot
- mount ${emmc_dev}p1 /tmp/boot
- rm -rf /tmp/boot/*
-
- # Clean /root partition - mkfs.f2fs is not available in chroot
- [ "$(grep -wo /dev/root /proc/mounts)" ] && umount /
- mkdir -p /tmp/rootpart
- mount ${emmc_dev}p3 /tmp/rootpart
- rm -rf /tmp/rootpart/*
-}
-
-platform_do_upgrade_uDPU() {
- udpu_check_emmc
-
- # Prepare and extract firmware on /misc partition
- udpu_do_misc_prep
-
- [ -f "/misc/firmware" ] && rm -r /misc/firmware
- mkdir -p /misc/firmware
- tar xzf "$1" -C /misc/firmware/
-
- udpu_do_regular_upgrade
-
- printf "Updating /boot partition\n"
- tar xzf /misc/firmware/boot.tgz -C /tmp/boot
- [ $? -eq 0 ] && printf "/boot partition updated successfully\n" || printf "/boot partition update failed\n"
- sync
-
- printf "Updating /root partition\n"
- tar xzf /misc/firmware/rootfs.tgz -C /tmp/rootpart
- [ $? -eq 0 ] && printf "/root partition updated successfully\n" || printf "/root partition update failed\n"
- sync
-
- # Saving configuration files over sysupgrade
- platform_copy_config_uDPU
-
- # Remove tmp mounts
- tmp_parts=$(grep "${emmc_dev}" /proc/mounts | awk '{print $2}')
- for part in ${tmp_parts}; do
- umount $part
- # Force umount is necessary
- [ "$(grep "${part}" /proc/mounts)" ] && umount -l $part
- done
-
- # Sysupgrade complains about /tmp and /dev, so we can detach them here
- umount -l /tmp
- umount -l /dev
-}
-
-platform_copy_config_uDPU() {
- # Config is saved on the /misc partition and copied on the rootfs after the reboot
- if [ -f "$UPGRADE_BACKUP" ]; then
- cp -f "$UPGRADE_BACKUP" "/misc/$BACKUP_FILE"
- sync
- fi
-}
--- /dev/null
+#!/bin/sh
+#
+# Copyright (C) 2014-2016 OpenWrt.org
+# Copyright (C) 2016 LEDE-Project.org
+#
+
+. /lib/functions/uci-defaults.sh
+
+board_config_update
+
+board=$(board_name)
+
+case "$board" in
+globalscale,espressobin|\
+globalscale,espressobin-emmc|\
+globalscale,espressobin-v7|\
+globalscale,espressobin-v7-emmc)
+ ucidef_set_interfaces_lan_wan "lan0 lan1" "wan"
+ ;;
+marvell,armada-3720-db|\
+methode,udpu)
+ ucidef_set_interfaces_lan_wan "eth1" "eth0"
+ ;;
+*)
+ ucidef_set_interface_lan "eth0"
+ ;;
+esac
+
+board_config_flush
+
+exit 0
--- /dev/null
+#
+# Copyright (C) 2014-2019 OpenWrt.org
+# Copyright (C) 2016 LEDE-Project.org
+#
+
+preinit_mount_udpu() {
+ . /lib/functions.sh
+ . /lib/upgrade/common.sh
+
+ case $(board_name) in
+ methode,udpu)
+ # Check which device is detected
+ [ -b "/dev/mmcblk0" ] && mmcdev="/dev/mmcblk0" || mmcdev="/dev/mmcblk1"
+
+ if [ -b "${mmcdev}p4" ]; then
+ mkdir /misc
+ mount -t f2fs ${mmcdev}p4 /misc
+ [ -f "/misc/$BACKUP_FILE" ] && {
+ echo "- Restoring configuration files -"
+ tar xzf "/misc/$BACKUP_FILE" -C /
+ rm -f "/misc/$BACKUP_FILE"
+ sync
+ }
+ [ -f "/misc/firmware/recovery.itb" ] && {
+ echo "- Updating /recovery partition -"
+ mkfs.ext4 -q ${mmcdev}p2 | echo y &> /dev/null
+ mkdir -p /tmp/recovery
+ mount ${mmcdev}p2 /tmp/recovery
+ cp /misc/firmware/recovery.itb /tmp/recovery
+ [ -f "/misc/firmware/boot.scr" ] && \
+ cp /misc/firmware/boot.scr /tmp/recovery
+ sync
+ umount /tmp/recovery
+ rm -rf /tmp/recovery
+
+ # Replace previous backup with the new one
+ [ -d "/misc/firmware_old" ] && rm -rf /misc/firmware_old
+ [ -d "/misc/firmware" ] && mv /misc/firmware /misc/firmware_old
+ }
+ fi
+
+ # Legacy support - if rootfs was booted, instruct u-boot to keep the current root dev
+ [ "$(df | grep /dev/root)" ] && fw_setenv root_ok '2'
+ ;;
+ esac
+}
+
+boot_hook_add preinit_main preinit_mount_udpu
--- /dev/null
+#
+# Copyright (C) 2014-2016 OpenWrt.org
+# Copyright (C) 2016 LEDE-Project.org
+#
+
+RAMFS_COPY_BIN='fw_printenv fw_setenv'
+RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
+REQUIRE_IMAGE_METADATA=1
+
+platform_check_image() {
+ case "$(board_name)" in
+ globalscale,espressobin|\
+ globalscale,espressobin-emmc|\
+ globalscale,espressobin-v7|\
+ globalscale,espressobin-v7-emmc)
+ platform_check_image_sdcard "$1"
+ ;;
+ *)
+ return 0
+ ;;
+ esac
+}
+
+platform_do_upgrade() {
+ case "$(board_name)" in
+ globalscale,espressobin|\
+ globalscale,espressobin-emmc|\
+ globalscale,espressobin-v7|\
+ globalscale,espressobin-v7-emmc)
+ platform_do_upgrade_sdcard "$1"
+ ;;
+ methode,udpu)
+ platform_do_upgrade_uDPU "$1"
+ ;;
+ *)
+ default_do_upgrade "$1"
+ ;;
+ esac
+}
+platform_copy_config() {
+ case "$(board_name)" in
+ globalscale,espressobin|\
+ globalscale,espressobin-emmc|\
+ globalscale,espressobin-v7|\
+ globalscale,espressobin-v7-emmc)
+ platform_copy_config_sdcard
+ ;;
+ methode,udpu)
+ platform_copy_config_uDPU
+ ;;
+ esac
+}
--- /dev/null
+udpu_check_emmc() {
+# uDPU uses combined ext4 and f2fs partitions.
+# partition layout:
+# 1. boot (ext4)
+# 2. recovery (ext4)
+# 3. rootfs (f2fs)
+# 4. misc (f2fs)
+
+ # Check which device is available, depending on the board revision
+ if [ -b "/dev/mmcblk1" ]; then
+ emmc_dev=/dev/mmcblk1
+ elif [ -b "/dev/mmcblk0" ]; then
+ emmc_dev=/dev/mmcblk0
+ else
+ echo "Cannot detect eMMC flash, aborting.."
+ exit 1
+ fi
+}
+
+udpu_part_prep() {
+ if [ "$(grep $1 /proc/mounts)" ]; then
+ mounted_part="$(grep $1 /proc/mounts | awk '{print $2}' | head -1)"
+ umount $mounted_part
+ [ "$(grep -wo $mounted_part /proc/mounts)" ] && umount -l $mounted_part
+ fi
+}
+
+udpu_do_part_check() {
+ local emmc_parts="1 2 3 4"
+ local part_valid="1"
+
+ # Check if the block devices exist
+ for num in ${emmc_parts}; do
+ [[ ! -b ${emmc_dev}p${num} ]] && part_valid="0"
+ done
+
+ # If partitions are missing create a new partition table
+ if [ "$part_valid" != "1" ]; then
+ printf "Invalid partition table, creating a new one\n"
+ printf "o\nn\np\n1\n\n+256M\nn\np\n2\n\n+256M\nn\np\n3\n\n+1536M\nn\np\n\n\nw\n" | fdisk -W always $emmc_dev > /dev/null 2>&1
+
+ # Format the /misc part right away as we will need it for the firmware
+ printf "Formating /misc partition, this make take a while..\n"
+ udpu_part_prep ${emmc_dev}p4
+ mkfs.f2fs -q -l misc ${emmc_dev}p4
+ [ $? -eq 0 ] && printf "/misc partition formated successfully\n" || printf "/misc partition formatting failed\n"
+
+ udpu_do_initial_setup
+ else
+ printf "Partition table looks ok\n"
+ fi
+}
+
+udpu_do_misc_prep() {
+ if [ ! "$(grep -wo /misc /proc/mounts)" ]; then
+ mkdir -p /misc
+ mount ${emmc_dev}p4 /misc
+
+ # If the mount fails, try to reformat partition
+ # Leaving possiblity for multiple iterations
+ if [ $? -ne 0 ]; then
+ printf "Error while mounting /misc, trying to reformat..\n"
+
+ format_count=0
+ while [ "$format_count" -lt "1" ]; do
+ udpu_part_prep ${emmc_dev}p4
+ mkfs.f2fs -q -l misc ${emmc_dev}p4
+ mount ${emmc_dev}p4 /misc
+ if [ $? -ne 0 ]; then
+ umount -l /misc
+ printf "Failed while mounting /misc\n"
+ format_count=$((format_count +1))
+ else
+ printf "Mounted /misc successfully\n"
+ break
+ fi
+ done
+ fi
+ fi
+}
+
+udpu_do_initial_setup() {
+ # Prepare /recovery parition
+ udpu_part_prep ${emmc_dev}p2
+ mkfs.ext4 -q ${emmc_dev}p2 | echo y &> /dev/null
+
+ # Prepare /boot partition
+ udpu_part_prep ${emmc_dev}p1
+ mkfs.ext4 -q ${emmc_dev}p1 | echo y &> /dev/null
+
+ # Prepare /root partition
+ printf "Formating /root partition, this may take a while..\n"
+ udpu_part_prep ${emmc_dev}p3
+ mkfs.f2fs -q -l rootfs ${emmc_dev}p3
+ [ $? -eq 0 ] && printf "/root partition reformated\n"
+}
+
+udpu_do_regular_upgrade() {
+ # Clean /boot partition - mfks.ext4 is not available in chroot
+ [ "$(grep -wo /boot /proc/mounts)" ] && umount /boot
+ mkdir -p /tmp/boot
+ mount ${emmc_dev}p1 /tmp/boot
+ rm -rf /tmp/boot/*
+
+ # Clean /root partition - mkfs.f2fs is not available in chroot
+ [ "$(grep -wo /dev/root /proc/mounts)" ] && umount /
+ mkdir -p /tmp/rootpart
+ mount ${emmc_dev}p3 /tmp/rootpart
+ rm -rf /tmp/rootpart/*
+}
+
+platform_do_upgrade_uDPU() {
+ udpu_check_emmc
+
+ # Prepare and extract firmware on /misc partition
+ udpu_do_misc_prep
+
+ [ -f "/misc/firmware" ] && rm -r /misc/firmware
+ mkdir -p /misc/firmware
+ tar xzf "$1" -C /misc/firmware/
+
+ udpu_do_regular_upgrade
+
+ printf "Updating /boot partition\n"
+ tar xzf /misc/firmware/boot.tgz -C /tmp/boot
+ [ $? -eq 0 ] && printf "/boot partition updated successfully\n" || printf "/boot partition update failed\n"
+ sync
+
+ printf "Updating /root partition\n"
+ tar xzf /misc/firmware/rootfs.tgz -C /tmp/rootpart
+ [ $? -eq 0 ] && printf "/root partition updated successfully\n" || printf "/root partition update failed\n"
+ sync
+
+ # Saving configuration files over sysupgrade
+ platform_copy_config_uDPU
+
+ # Remove tmp mounts
+ tmp_parts=$(grep "${emmc_dev}" /proc/mounts | awk '{print $2}')
+ for part in ${tmp_parts}; do
+ umount $part
+ # Force umount is necessary
+ [ "$(grep "${part}" /proc/mounts)" ] && umount -l $part
+ done
+
+ # Sysupgrade complains about /tmp and /dev, so we can detach them here
+ umount -l /tmp
+ umount -l /dev
+}
+
+platform_copy_config_uDPU() {
+ # Config is saved on the /misc partition and copied on the rootfs after the reboot
+ if [ -f "$UPGRADE_BACKUP" ]; then
+ cp -f "$UPGRADE_BACKUP" "/misc/$BACKUP_FILE"
+ sync
+ fi
+}
--- /dev/null
+#!/bin/sh
+#
+# Copyright (C) 2014-2016 OpenWrt.org
+# Copyright (C) 2016 LEDE-Project.org
+#
+
+. /lib/functions/uci-defaults.sh
+
+board_config_update
+
+board=$(board_name)
+
+case "$board" in
+marvell,armada8040-mcbin)
+ ucidef_set_interfaces_lan_wan "eth0 eth1 eth3" "eth2"
+ ;;
+marvell,armada8040-db)
+ ucidef_set_interfaces_lan_wan "eth0 eth2 eth3" "eth1"
+ ;;
+marvell,armada7040-db)
+ ucidef_set_interfaces_lan_wan "eth0 eth2" "eth1"
+ ;;
+*)
+ ucidef_set_interface_lan "eth0"
+ ;;
+esac
+
+board_config_flush
+
+exit 0
--- /dev/null
+#
+# Copyright (C) 2014-2016 OpenWrt.org
+# Copyright (C) 2016 LEDE-Project.org
+#
+
+RAMFS_COPY_BIN='fw_printenv fw_setenv'
+RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
+REQUIRE_IMAGE_METADATA=1
+
+platform_check_image() {
+ case "$(board_name)" in
+ marvell,armada8040-mcbin)
+ platform_check_image_sdcard "$1"
+ ;;
+ *)
+ return 0
+ ;;
+ esac
+}
+
+platform_do_upgrade() {
+ case "$(board_name)" in
+ marvell,armada8040-mcbin)
+ platform_do_upgrade_sdcard "$1"
+ ;;
+ *)
+ default_do_upgrade "$1"
+ ;;
+ esac
+}
+platform_copy_config() {
+ case "$(board_name)" in
+ marvell,armada8040-mcbin)
+ platform_copy_config_sdcard
+ ;;
+ esac
+}
--- /dev/null
+#!/bin/sh
+#
+# Copyright (C) 2014-2016 OpenWrt.org
+# Copyright (C) 2016 LEDE-Project.org
+#
+
+. /lib/functions/uci-defaults.sh
+
+board_config_update
+
+board=$(board_name)
+boardname="${board##*,}"
+
+case "$board" in
+linksys,caiman|\
+linksys,cobra|\
+linksys,rango|\
+linksys,shelby)
+ ucidef_set_led_netdev "wan" "WAN" "pca963x:$boardname:white:wan" "eth1"
+ ucidef_set_led_usbport "usb1" "USB 1" "pca963x:$boardname:white:usb2" "usb1-port1"
+ ucidef_set_led_usbport "usb2" "USB 2" "pca963x:$boardname:white:usb3_1" "usb2-port1" "usb3-port1"
+ ucidef_set_led_usbport "usb2_ss" "USB 2 SS" "pca963x:$boardname:white:usb3_2" "usb3-port1"
+ ;;
+linksys,mamba)
+ ucidef_set_led_netdev "wan" "WAN" "mamba:white:wan" "eth1"
+ ucidef_set_led_usbport "usb1" "USB 1" "mamba:white:usb2" "usb1-port1"
+ ucidef_set_led_usbport "usb2" "USB 2" "mamba:white:usb3_1" "usb2-port1" "usb3-port1"
+ ucidef_set_led_usbport "usb2_ss" "USB 2 SS" "mamba:white:usb3_2" "usb3-port2"
+ ;;
+linksys,venom)
+ ucidef_set_led_netdev "wan" "WAN" "pca963x:venom:blue:wan" "eth1"
+ ucidef_set_led_usbport "usb1" "USB 1" "pca963x:venom:blue:usb2" "usb1-port1"
+ ucidef_set_led_usbport "usb2" "USB 2" "pca963x:venom:blue:usb3_1" "usb2-port1" "usb3-port1"
+ ucidef_set_led_usbport "usb2_ss" "USB 2 SS" "pca963x:venom:blue:usb3_2" "usb3-port1"
+ ;;
+esac
+
+board_config_flush
+
+exit 0
--- /dev/null
+#!/bin/sh
+#
+# Copyright (C) 2014-2016 OpenWrt.org
+# Copyright (C) 2016 LEDE-Project.org
+#
+
+. /lib/functions/uci-defaults.sh
+
+board_config_update
+
+board=$(board_name)
+
+case "$board" in
+cznic,turris-omnia)
+ ucidef_set_interface_lan "lan0 lan1 lan2 lan3 lan4"
+ ucidef_set_interface_wan "eth2"
+ ;;
+linksys,caiman|\
+linksys,cobra|\
+linksys,mamba|\
+linksys,rango|\
+linksys,shelby|\
+linksys,venom)
+ ucidef_set_interfaces_lan_wan "eth0.1" "eth1.2"
+ ucidef_add_switch "switch0" \
+ "0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "5@eth0" "4:wan" "6@eth1"
+ ;;
+marvell,a385-db-ap)
+ ucidef_set_interfaces_lan_wan "eth0 eth1" "eth2"
+ ;;
+marvell,axp-gp)
+ ucidef_set_interface_lan "eth0 eth1 eth2 eth3"
+ ;;
+solidrun,clearfog-a1|\
+solidrun,clearfog-pro-a1)
+ # eth0 is standalone ethernet
+ # eth1 is switch
+ # eth2 is SFP
+ ucidef_set_interfaces_lan_wan "eth1" "eth0 eth2"
+
+ # switch port 5 is connected to eth1
+ ucidef_add_switch "switch0" \
+ "0:lan:5" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5u@eth1" "6:lan:6"
+ ;;
+solidrun,clearfog-base-a1)
+ # eth0 is standalone ethernet
+ # eth1 is standalone ethernet
+ # eth2 is SFP
+ ucidef_set_interfaces_lan_wan "eth1" "eth0 eth2"
+ ;;
+*)
+ ucidef_set_interface_lan "eth0"
+ ;;
+esac
+
+board_config_flush
+
+exit 0
--- /dev/null
+#!/bin/sh /etc/rc.common
+
+START=99
+
+boot() {
+ case $(board_name) in
+ linksys,caiman |\
+ linksys,cobra |\
+ linksys,mamba |\
+ linksys,rango |\
+ linksys,shelby |\
+ linksys,venom)
+ mtd resetbc s_env || true
+ ;;
+ esac
+}
--- /dev/null
+#!/bin/sh
+#
+# Copyright (C) 2015 OpenWrt.org
+#
+
+[ ! -e /etc/config/wireless ] && exit 0
+
+. /lib/functions.sh
+. /lib/functions/system.sh
+
+board=$(board_name)
+
+case "$board" in
+linksys,caiman|linksys,cobra|linksys,mamba|linksys,shelby|linksys,venom)
+ SKU=$(strings /dev/mtd3|sed -ne 's/^cert_region=//p')
+ WIFIMAC2G=$(macaddr_add $(cat /sys/class/net/eth0/address) +1)
+ WIFIMAC5G=$(macaddr_add $WIFIMAC2G +1)
+ case "$SKU" in
+ AP)
+ REGD=CN
+ ;;
+ AU)
+ REGD=AU
+ ;;
+ CA)
+ REGD=CA
+ ;;
+ EU)
+ REGD=DE
+ ;;
+ US)
+ REGD=US
+ ;;
+ esac
+
+ case "$board" in
+ linksys,mamba)
+ WIFIMAC0=$WIFIMAC2G
+ WIFIMAC1=$WIFIMAC5G
+ ;;
+ *)
+ WIFIMAC0=$WIFIMAC5G
+ WIFIMAC1=$WIFIMAC2G
+ ;;
+ esac
+
+ uci get wireless.radio0.country || uci set wireless.radio0.country=$REGD
+ uci get wireless.@wifi-iface[0].macaddr || uci set wireless.@wifi-iface[0].macaddr=$WIFIMAC0
+ uci get wireless.radio1.country || uci set wireless.radio1.country=$REGD
+ uci get wireless.@wifi-iface[1].macaddr || uci set wireless.@wifi-iface[1].macaddr=$WIFIMAC1
+ ;;
+esac
+
+uci commit wireless
+
+exit 0
--- /dev/null
+#!/bin/sh
+#
+# Copyright (C) 2017 LEDE-Project.org
+#
+
+. /lib/functions.sh
+
+board=$(board_name)
+
+case "$board" in
+linksys,mamba)
+ # Set fan script execution in crontab
+ grep -s -q fan_ctrl.sh /etc/crontabs/root && exit 0
+
+ echo "# mamba fan script runs every 5 minutes" >> /etc/crontabs/root
+ echo "*/5 * * * * /sbin/fan_ctrl.sh" >> /etc/crontabs/root
+
+ # Execute one time after initial flash (instead of waiting 5 min for cron)
+ /sbin/fan_ctrl.sh
+ ;;
+esac
+
+exit 0
--- /dev/null
+#
+# Copyright (C) 2014-2015 OpenWrt.org
+# Copyright (C) 2016 LEDE-Project.org
+#
+
+preinit_set_mac_address() {
+ local mac
+
+ . /lib/functions.sh
+
+ case $(board_name) in
+ linksys,caiman|linksys,cobra|linksys,rango|linksys,shelby|linksys,venom)
+ # rename interfaces back to the way they were with 4.4
+ case "$(readlink /sys/class/net/eth0)" in
+ *f1070000*)
+ ip link set eth0 name tmp0
+ ip link set eth1 name eth0
+ ip link set tmp0 name eth1
+ ;;
+ esac
+
+ mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
+ mac_wan=$(macaddr_setbit_la "$mac")
+ ip link set dev eth0 address $mac 2>/dev/null
+ ip link set dev eth1 address $mac_wan 2>/dev/null
+ ;;
+ linksys,mamba)
+ mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
+ ip link set dev eth0 address $mac 2>/dev/null
+ ip link set dev eth1 address $mac 2>/dev/null
+ ;;
+ marvell,a385-db-ap|solidrun,clearfog*a1)
+ # rename interfaces back to the way they were with 4.4
+ case "$(readlink /sys/class/net/eth0)" in
+ *f1070000*)
+ ip link set eth0 name tmp0
+ ip link set eth1 name eth0
+ ip link set eth2 name eth1
+ ip link set tmp0 name eth2
+ ;;
+ esac
+ ;;
+ esac
+}
+
+boot_hook_add preinit_main preinit_set_mac_address
--- /dev/null
+#
+# Copyright (C) 2014-2016 OpenWrt.org
+# Copyright (C) 2016 LEDE-Project.org
+#
+
+preinit_mount_syscfg() {
+ . /lib/functions.sh
+ . /lib/upgrade/common.sh
+
+ case $(board_name) in
+ linksys,caiman|linksys,cobra|linksys,mamba|linksys,rango|linksys,shelby|linksys,venom)
+ needs_recovery=0
+ syscfg_part=$(grep syscfg /proc/mtd |cut -c4)
+ ubiattach -m $syscfg_part || needs_recovery=1
+ if [ $needs_recovery -eq 1 ]
+ then
+ echo "ubifs syscfg partition is damaged, reformatting"
+ ubidetach -m $syscfg_part
+ ubiformat -y -O 2048 -q /dev/mtd$syscfg_part
+ ubiattach -m $syscfg_part
+ ubimkvol /dev/ubi1 -n 0 -N syscfg -t dynamic --maxavsize
+ fi
+ mkdir /tmp/syscfg
+ mount -t ubifs ubi1:syscfg /tmp/syscfg
+ [ -f "/tmp/syscfg/$BACKUP_FILE" ] && {
+ echo "- config restore -"
+ cd /
+ mv "/tmp/syscfg/$BACKUP_FILE" /tmp
+ tar xzf "/tmp/$BACKUP_FILE"
+ rm -f "/tmp/$BACKUP_FILE"
+ sync
+ }
+ ;;
+ esac
+}
+
+boot_hook_add preinit_main preinit_mount_syscfg
--- /dev/null
+#
+# Copyright (C) 2014-2015 OpenWrt.org
+#
+
+linksys_get_target_firmware() {
+
+ local cur_boot_part mtd_ubi0
+
+ cur_boot_part=$(/usr/sbin/fw_printenv -n boot_part)
+ if [ -z "${cur_boot_part}" ] ; then
+ mtd_ubi0=$(cat /sys/devices/virtual/ubi/ubi0/mtd_num)
+ case $(egrep ^mtd${mtd_ubi0}: /proc/mtd | cut -d '"' -f 2) in
+ kernel1|rootfs1)
+ cur_boot_part=1
+ ;;
+ kernel2|rootfs2)
+ cur_boot_part=2
+ ;;
+ esac
+ >&2 printf "Current boot_part='%s' selected from ubi0/mtd_num='%s'" \
+ "${cur_boot_part}" "${mtd_ubi0}"
+ fi
+
+ case $cur_boot_part in
+ 1)
+ fw_setenv -s - <<-EOF
+ boot_part 2
+ bootcmd "run altnandboot"
+ EOF
+ printf "kernel2"
+ return
+ ;;
+ 2)
+ fw_setenv -s - <<-EOF
+ boot_part 1
+ bootcmd "run nandboot"
+ EOF
+ printf "kernel1"
+ return
+ ;;
+ *)
+ return
+ ;;
+ esac
+}
+
+linksys_get_root_magic() {
+ (get_image "$@" | dd skip=786432 bs=4 count=1 | hexdump -v -n 4 -e '1/1 "%02x"') 2>/dev/null
+}
+
+platform_do_upgrade_linksys() {
+ local magic_long="$(get_magic_long "$1")"
+
+ mkdir -p /var/lock
+ local part_label="$(linksys_get_target_firmware)"
+ touch /var/lock/fw_printenv.lock
+
+ if [ ! -n "$part_label" ]
+ then
+ echo "cannot find target partition"
+ exit 1
+ fi
+
+ local target_mtd=$(find_mtd_part $part_label)
+
+ [ "$magic_long" = "73797375" ] && {
+ CI_KERNPART="$part_label"
+ if [ "$part_label" = "kernel1" ]
+ then
+ CI_UBIPART="rootfs1"
+ else
+ CI_UBIPART="rootfs2"
+ fi
+
+ nand_upgrade_tar "$1"
+ }
+ [ "$magic_long" = "27051956" -o "$magic_long" = "0000a0e1" ] && {
+ # check firmwares' rootfs types
+ local target_mtd=$(find_mtd_part $part_label)
+ local oldroot="$(linksys_get_root_magic $target_mtd)"
+ local newroot="$(linksys_get_root_magic "$1")"
+
+ if [ "$newroot" = "55424923" -a "$oldroot" = "55424923" ]
+ # we're upgrading from a firmware with UBI to one with UBI
+ then
+ # erase everything to be safe
+ mtd erase $part_label
+ get_image "$1" | mtd -n write - $part_label
+ else
+ get_image "$1" | mtd write - $part_label
+ fi
+ }
+}
+
+platform_copy_config_linksys() {
+ cp -f "$UPGRADE_BACKUP" "/tmp/syscfg/$BACKUP_FILE"
+ sync
+}
--- /dev/null
+#
+# Copyright (C) 2014-2016 OpenWrt.org
+# Copyright (C) 2016 LEDE-Project.org
+#
+
+RAMFS_COPY_BIN='fw_printenv fw_setenv'
+RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
+REQUIRE_IMAGE_METADATA=1
+
+platform_check_image() {
+ case "$(board_name)" in
+ cznic,turris-omnia|\
+ solidrun,clearfog-base-a1|\
+ solidrun,clearfog-pro-a1)
+ platform_check_image_sdcard "$1"
+ ;;
+ *)
+ return 0
+ ;;
+ esac
+}
+
+platform_do_upgrade() {
+ case "$(board_name)" in
+ cznic,turris-omnia|\
+ solidrun,clearfog-base-a1|\
+ solidrun,clearfog-pro-a1)
+ platform_do_upgrade_sdcard "$1"
+ ;;
+ linksys,caiman|\
+ linksys,cobra|\
+ linksys,mamba|\
+ linksys,rango|\
+ linksys,shelby|\
+ linksys,venom)
+ platform_do_upgrade_linksys "$1"
+ ;;
+ *)
+ default_do_upgrade "$1"
+ ;;
+ esac
+}
+platform_copy_config() {
+ case "$(board_name)" in
+ cznic,turris-omnia|\
+ solidrun,clearfog-base-a1|\
+ solidrun,clearfog-pro-a1)
+ platform_copy_config_sdcard
+ ;;
+ linksys,caiman|\
+ linksys,cobra|\
+ linksys,mamba|\
+ linksys,rango|\
+ linksys,shelby|\
+ linksys,venom)
+ platform_copy_config_linksys
+ ;;
+ esac
+}