--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019-ap.dk01.1.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ aliases {
+ label-mac-device = &gmac0;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>;
+ };
+
+ soc {
+ pinctrl@1000000 {
+ mdio_pins: mdio_pinmux {
+ mux_1 {
+ pins = "gpio53";
+ function = "mdio";
+ bias-pull-up;
+ };
+ mux_2 {
+ pins = "gpio52";
+ function = "mdc";
+ bias-pull-up;
+ };
+ };
+
+ i2c_0_pins: i2c_0_pinmux {
+ mux {
+ pins = "gpio58", "gpio59";
+ function = "blsp_i2c0";
+ bias-disable;
+ };
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 4 1>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ gpio_export {
+ compatible = "gpio-export";
+ #size-cells = <0>;
+
+ gpio_out {
+ gpio-export,name = "gpio_out";
+ gpio-export,output = <0>;
+ gpio-export,direction_may_change = <0>;
+ gpios = <&stm32_io 23 GPIO_ACTIVE_HIGH>;
+ };
+
+ gpio_in {
+ gpio-export,name = "gpio_in";
+ gpio-export,input = <0>;
+ gpio-export,direction_may_change = <0>;
+ gpios = <&stm32_io 24 GPIO_ACTIVE_LOW>;
+ };
+ };
+ };
+};
+
+&blsp1_i2c3 {
+ status = "okay";
+ pinctrl-0 = <&i2c_0_pins>;
+ pinctrl-names = "default";
+ clock-frequency = <400000>;
+
+ stm32_io: stm32@74 {
+ compatible = "tlt,stm32v1";
+ #gpio-cells = <2>;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ interrupt-parent = <&tlmm>;
+ interrupts = <5 2>;
+ reg = <0x74>;
+ };
+};
+
+&blsp1_spi1 {
+ cs-gpios = <&tlmm 54 0>, <&tlmm 63 0>;
+ num-cs = <2>;
+
+ xt25f128b@0 {
+ /*
+ * Factory U-boot looks in 0:BOOTCONFIG partition for active
+ * partitions settings and mangles the partition config so
+ * 0:QSEE/0:QSEE_1, 0:CDT/0:CDT_1 and 0:APPSBL/0:APPSBL_1 pairs
+ * can be swaped. It isn't a problem but we never can be sure where
+ * OFW put factory images. "n25q128a11" is required for proper nor
+ * recognition in u-boot.
+ */
+ compatible = "jedec,spi-nor", "n25q128a11";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "0:SBL1";
+ reg = <0x0 0x40000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "0:MIBIB";
+ reg = <0x40000 0x20000>;
+ read-only;
+ };
+
+ partition@60000 {
+ label = "0:BOOTCONFIG";
+ reg = <0x60000 0x20000>;
+ read-only;
+ };
+
+ partition@80000 {
+ label = "0:BOOTCONFIG1";
+ reg = <0x80000 0x20000>;
+ read-only;
+ };
+
+ partition@a0000 {
+ label = "0:QSEE";
+ reg = <0xa0000 0x60000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "0:QSEE_1";
+ reg = <0x100000 0x60000>;
+ read-only;
+ };
+
+ partition@160000 {
+ label = "0:CDT";
+ reg = <0x160000 0x10000>;
+ read-only;
+ };
+
+ partition@170000 {
+ label = "0:CDT_1";
+ reg = <0x170000 0x10000>;
+ read-only;
+ };
+
+ partition@180000 {
+ label = "0:DDRPARAMS";
+ reg = <0x180000 0x10000>;
+ read-only;
+ };
+
+ partition@190000 {
+ label = "0:APPSBLENV";
+ reg = <0x190000 0x10000>;
+ read-only;
+ };
+
+ partition@1a0000 {
+ label = "0:APPSBL";
+ reg = <0x1a0000 0xa0000>;
+ read-only;
+ };
+
+ partition@240000 {
+ label = "0:APPSBL_1";
+ reg = <0x240000 0xa0000>;
+ read-only;
+ };
+
+ partition@2e0000 {
+ label = "0:ART";
+ reg = <0x2e0000 0x10000>;
+ read-only;
+ };
+
+ config: partition@2f0000 {
+ label = "0:CONFIG";
+ reg = <0x2f0000 0x10000>;
+ read-only;
+ };
+
+ partition@300000 {
+ label = "0:CONFIG_RW";
+ reg = <0x300000 0x10000>;
+ read-only;
+ };
+
+ partition@310000 {
+ label = "0:EVENTSLOG";
+ reg = <0x310000 0x90000>;
+ read-only;
+ };
+ };
+ };
+
+ xt26g02a@1 {
+ /*
+ * Factory U-boot looks in 0:BOOTCONFIG partition for active
+ * partitions settings and mangles the partition config so
+ * rootfs/rootfs_1 pairs can be swaped.
+ * It isn't a problem but we never can be sure where OFW put
+ * factory images. "spinand,mt29f" value is required for proper
+ * nand recognition in u-boot.
+ */
+ compatible = "spi-nand", "spinand,mt29f";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <1>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "rootfs_1";
+ reg = <0x00000000 0x08000000>;
+ };
+
+ partition@8000000 {
+ label = "rootfs";
+ reg = <0x08000000 0x08000000>;
+ };
+ };
+ };
+};
+
+&mdio {
+ status = "okay";
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+ phy-reset-gpio = <&tlmm 62 0>;
+};
dd if=$@.new bs=64 count=1 >> $(IMAGE_KERNEL)
endef
+define Build/append-rutx-metadata
+ echo \
+ '{ \
+ "device_code": [".*"], \
+ "hwver": [".*"], \
+ "batch": [".*"], \
+ "serial": [".*"], \
+ "supported_devices":["teltonika,rutx"] \
+ }' | fwtool -I - $@
+endef
+
define Build/mkmylofw_32m
$(eval device_id=$(word 1,$(1)))
$(eval revision=$(word 2,$(1)))
endef
TARGET_DEVICES += qxwlan_e2600ac-c2
+define Device/teltonika_rutx10
+ $(call Device/FitImage)
+ $(call Device/UbiFit)
+ DEVICE_VENDOR := Teltonika
+ DEVICE_MODEL := RUTX10
+ SOC := qcom-ipq4018
+ DEVICE_DTS_CONFIG := config@5
+ KERNEL_INSTALL := 1
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ FILESYSTEMS := squashfs
+ IMAGE/nand-factory.ubi := append-ubi | qsdk-ipq-factory-nand | append-rutx-metadata
+ DEVICE_PACKAGES := ipq-wifi-teltonika_rutx kmod-bluetooth
+endef
+TARGET_DEVICES += teltonika_rutx10
+
define Device/unielec_u4019-32m
$(call Device/FitImage)
DEVICE_VENDOR := Unielec
projects / openwrt / staging / rmilecki.git / commitdiff