--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca955x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "aruba,ap-115", "qca,qca9558";
+ model = "Aruba AP-115";
+
+ aliases {
+ led-boot = &led_power_green;
+ led-failsafe = &led_power_red;
+ led-running = &led_power_green;
+ led-upgrade = &led_power_red;
+ label-mac-device = ð0;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,9600n8";
+ };
+
+ /**
+ * Currently unused GPIOs in OpenWrt:
+ *
+ * TPM-CLK: 19
+ * TPM-IO: 20
+ * ETH-PHY-Interrupt: 11
+ * Power-DC: 22
+ * Power-PoE: 23
+ * Power-PoE-8023af: 17
+ */
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power_green: power-green {
+ label = "green:power";
+ gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+ };
+
+ led_power_red: power-red {
+ label = "red:power";
+ gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+ };
+
+ radio-24-green {
+ label = "green:radio-24";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ radio-24-amber {
+ label = "amber:radio-24";
+ gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+ };
+
+ radio-5-green {
+ label = "green:radio-5";
+ gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ radio-5-amber {
+ label = "amber:radio-5";
+ gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ reg_usb_vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio 3 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+};
+
+&pcie0 {
+ status = "okay";
+
+ ath9k: wifi@0,0 {
+ compatible = "pci168c,0033";
+ reg = <0x0000 0 0 0 0>;
+ qca,no-eeprom;
+
+ nvmem-cells = <&macaddr_oemdata_1d>;
+ nvmem-cell-names = "mac-address";
+
+ mac-address-increment = <1>;
+ };
+};
+
+&pinmux {
+ /**
+ * Ugly hack ahead!
+ *
+ * GPIO05: Bank1-CS / Bank2-CLK
+ * GPIO14: Bank1-CLK / Bank2-CS
+ *
+ * We can not support this with OpenWrt, as this
+ * would require us to influence the pinmux based on the CS.
+ *
+ * We force-select Bank 1. Remember to blame Aruba for that.
+ */
+ cs0_pin5: spi-cs0-pin5 {
+ pinctrl-single,bits = <0x4 0x900 0xff00>;
+ };
+
+ clk_pin14: spi-cs1-pin14 {
+ pinctrl-single,bits = <0xc 0x0a0000 0xff0000>;
+ };
+};
+
+&spi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cs0_pin5 &clk_pin14>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@1 {
+ label = "flash-full";
+ reg = <0x0 0x1000000>;
+ read-only;
+ };
+
+ uboot: partition@0 {
+ label = "u-boot";
+ reg = <0x000000 0x040000>;
+ read-only;
+ };
+
+ /* Here be dragons */
+
+ partition@100000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x100000 0xe00000>;
+ };
+
+ oemdata: partition@fe0000 {
+ label = "oemdata";
+ reg = <0xfe0000 0x010000>;
+ read-only;
+ };
+
+ partition@ff0000 {
+ label = "u-boot-env";
+ reg = <0xff0000 0x10000>;
+ };
+ };
+ };
+};
+
+&wmac {
+ status = "okay";
+
+ qca,no-eeprom;
+ nvmem-cells = <&macaddr_oemdata_1d>;
+ nvmem-cell-names = "mac-address";
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+
+ reset-gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <10000>;
+
+ eee-broken-100tx;
+ eee-broken-1000t;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ nvmem-cells = <&macaddr_oemdata_1d>;
+ nvmem-cell-names = "mac-address";
+
+ phy-handle = <&phy0>;
+ phy-mode = "rgmii-id";
+
+ pll-data = <0xa6000000 0xa0000101 0xa0001313>;
+
+ gmac-config {
+ device = <&gmac>;
+ ge0-sgmii = <0>;
+ txen-delay = <3>;
+ txd-delay = <3>;
+ rxdv-delay = <3>;
+ rxd-delay = <3>;
+ rgmii-enabled = <1>;
+ };
+};
+
+&oemdata {
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_oemdata_1d: macaddr@1d {
+ reg = <0x1d 0x6>;
+ };
+};
+
+&usb_phy0 {
+ status = "okay";
+};
+
+&usb0 {
+ dr_mode = "host";
+ status = "okay";
+};
projects / openwrt / openwrt.git / commitdiff