--- /dev/null
+/*
+ * (C) Copyright 2015 Linaro
+ * Peter Griffin <peter.griffin@linaro.org>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#include <common.h>
+#include <dm.h>
+#include <errno.h>
+#include <malloc.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <usb.h>
+#include <power/hi6553_pmic.h>
+#include <asm-generic/gpio.h>
+#include <asm/arch/dwmmc.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/periph.h>
+#include <asm/arch/pinmux.h>
+#include <asm/arch/hi6220.h>
+
+/*TODO drop this table in favour of device tree */
+static const struct hikey_gpio_platdata hi6220_gpio[] = {
+ { 0, HI6220_GPIO_BASE(0)},
+ { 1, HI6220_GPIO_BASE(1)},
+ { 2, HI6220_GPIO_BASE(2)},
+ { 3, HI6220_GPIO_BASE(3)},
+ { 4, HI6220_GPIO_BASE(4)},
+ { 5, HI6220_GPIO_BASE(5)},
+ { 6, HI6220_GPIO_BASE(6)},
+ { 7, HI6220_GPIO_BASE(7)},
+ { 8, HI6220_GPIO_BASE(8)},
+ { 9, HI6220_GPIO_BASE(9)},
+ { 10, HI6220_GPIO_BASE(10)},
+ { 11, HI6220_GPIO_BASE(11)},
+ { 12, HI6220_GPIO_BASE(12)},
+ { 13, HI6220_GPIO_BASE(13)},
+ { 14, HI6220_GPIO_BASE(14)},
+ { 15, HI6220_GPIO_BASE(15)},
+ { 16, HI6220_GPIO_BASE(16)},
+ { 17, HI6220_GPIO_BASE(17)},
+ { 18, HI6220_GPIO_BASE(18)},
+ { 19, HI6220_GPIO_BASE(19)},
+
+};
+
+U_BOOT_DEVICES(hi6220_gpios) = {
+ { "gpio_hi6220", &hi6220_gpio[0] },
+ { "gpio_hi6220", &hi6220_gpio[1] },
+ { "gpio_hi6220", &hi6220_gpio[2] },
+ { "gpio_hi6220", &hi6220_gpio[3] },
+ { "gpio_hi6220", &hi6220_gpio[4] },
+ { "gpio_hi6220", &hi6220_gpio[5] },
+ { "gpio_hi6220", &hi6220_gpio[6] },
+ { "gpio_hi6220", &hi6220_gpio[7] },
+ { "gpio_hi6220", &hi6220_gpio[8] },
+ { "gpio_hi6220", &hi6220_gpio[9] },
+ { "gpio_hi6220", &hi6220_gpio[10] },
+ { "gpio_hi6220", &hi6220_gpio[11] },
+ { "gpio_hi6220", &hi6220_gpio[12] },
+ { "gpio_hi6220", &hi6220_gpio[13] },
+ { "gpio_hi6220", &hi6220_gpio[14] },
+ { "gpio_hi6220", &hi6220_gpio[15] },
+ { "gpio_hi6220", &hi6220_gpio[16] },
+ { "gpio_hi6220", &hi6220_gpio[17] },
+ { "gpio_hi6220", &hi6220_gpio[18] },
+ { "gpio_hi6220", &hi6220_gpio[19] },
+};
+
+DECLARE_GLOBAL_DATA_PTR;
+
+struct peri_sc_periph_regs *peri_sc =
+ (struct peri_sc_periph_regs *)HI6220_PERI_BASE;
+
+struct alwayson_sc_regs *ao_sc =
+ (struct alwayson_sc_regs *)ALWAYSON_CTRL_BASE;
+
+/* status offset from enable reg */
+#define STAT_EN_OFF 0x2
+
+void hi6220_clk_enable(u32 bitfield, unsigned int *clk_base)
+{
+ uint32_t data;
+
+ data = readl(clk_base);
+ data |= bitfield;
+
+ writel(bitfield, clk_base);
+ do {
+ data = readl(clk_base + STAT_EN_OFF);
+ } while ((data & bitfield) == 0);
+}
+
+/* status offset from disable reg */
+#define STAT_DIS_OFF 0x1
+
+void hi6220_clk_disable(u32 bitfield, unsigned int *clk_base)
+{
+ uint32_t data;
+
+ data = readl(clk_base);
+ data |= bitfield;
+
+ writel(data, clk_base);
+ do {
+ data = readl(clk_base + STAT_DIS_OFF);
+ } while (data & bitfield);
+}
+
+#define EYE_PATTERN 0x70533483
+
+int board_usb_init(int index, enum usb_init_type init)
+{
+ unsigned int data;
+
+ /* enable USB clock */
+ hi6220_clk_enable(PERI_CLK0_USBOTG, &peri_sc->clk0_en);
+
+ /* take usb IPs out of reset */
+ writel(PERI_RST0_USBOTG_BUS | PERI_RST0_POR_PICOPHY |
+ PERI_RST0_USBOTG | PERI_RST0_USBOTG_32K,
+ &peri_sc->rst0_dis);
+ do {
+ data = readl(&peri_sc->rst0_stat);
+ data &= PERI_RST0_USBOTG_BUS | PERI_RST0_POR_PICOPHY |
+ PERI_RST0_USBOTG | PERI_RST0_USBOTG_32K;
+ } while (data);
+
+ /*CTRL 5*/
+ data = readl(&peri_sc->ctrl5);
+ data &= ~PERI_CTRL5_PICOPHY_BC_MODE;
+ data |= PERI_CTRL5_USBOTG_RES_SEL | PERI_CTRL5_PICOPHY_ACAENB;
+ data |= 0x300;
+ writel(data, &peri_sc->ctrl5);
+
+ /*CTRL 4*/
+
+ /* configure USB PHY */
+ data = readl(&peri_sc->ctrl4);
+
+ /* make PHY out of low power mode */
+ data &= ~PERI_CTRL4_PICO_SIDDQ;
+ data &= ~PERI_CTRL4_PICO_OGDISABLE;
+ data |= PERI_CTRL4_PICO_VBUSVLDEXTSEL | PERI_CTRL4_PICO_VBUSVLDEXT;
+ writel(data, &peri_sc->ctrl4);
+
+ writel(EYE_PATTERN, &peri_sc->ctrl8);
+
+ mdelay(5);
+ return 0;
+}
+
+static int config_sd_carddetect(void)
+{
+ int ret;
+
+ /* configure GPIO8 as nopull */
+ writel(0, 0xf8001830);
+
+ gpio_request(8, "SD CD");
+
+ gpio_direction_input(8);
+ ret = gpio_get_value(8);
+
+ if (!ret) {
+ printf("%s: SD card present\n", __func__);
+ return 1;
+ }
+
+ printf("%s: SD card not present\n", __func__);
+ return 0;
+}
+
+
+static void mmc1_init_pll(void)
+{
+ uint32_t data;
+
+ /* select SYSPLL as the source of MMC1 */
+ /* select SYSPLL as the source of MUX1 (SC_CLK_SEL0) */
+ writel(1 << 11 | 1 << 27, &peri_sc->clk0_sel);
+ do {
+ data = readl(&peri_sc->clk0_sel);
+ } while (!(data & (1 << 11)));
+
+ /* select MUX1 as the source of MUX2 (SC_CLK_SEL0) */
+ writel(1 << 30, &peri_sc->clk0_sel);
+ do {
+ data = readl(&peri_sc->clk0_sel);
+ } while (data & (1 << 14));
+
+ hi6220_clk_enable(PERI_CLK0_MMC1, &peri_sc->clk0_en);
+
+ hi6220_clk_enable(PERI_CLK12_MMC1_SRC, &peri_sc->clk12_en);
+
+ do {
+ /* 1.2GHz / 50 = 24MHz */
+ writel(0x31 | (1 << 7), &peri_sc->clkcfg8bit2);
+ data = readl(&peri_sc->clkcfg8bit2);
+ } while ((data & 0x31) != 0x31);
+}
+
+static void mmc1_reset_clk(void)
+{
+ unsigned int data;
+
+ /* disable mmc1 bus clock */
+ hi6220_clk_disable(PERI_CLK0_MMC1, &peri_sc->clk0_dis);
+
+ /* enable mmc1 bus clock */
+ hi6220_clk_enable(PERI_CLK0_MMC1, &peri_sc->clk0_en);
+
+ /* reset mmc1 clock domain */
+ writel(PERI_RST0_MMC1, &peri_sc->rst0_en);
+
+ /* bypass mmc1 clock phase */
+ data = readl(&peri_sc->ctrl2);
+ data |= 3 << 2;
+ writel(data, &peri_sc->ctrl2);
+
+ /* disable low power */
+ data = readl(&peri_sc->ctrl13);
+ data |= 1 << 4;
+ writel(data, &peri_sc->ctrl13);
+ do {
+ data = readl(&peri_sc->rst0_stat);
+ } while (!(data & PERI_RST0_MMC1));
+
+ /* unreset mmc0 clock domain */
+ writel(PERI_RST0_MMC1, &peri_sc->rst0_dis);
+ do {
+ data = readl(&peri_sc->rst0_stat);
+ } while (data & PERI_RST0_MMC1);
+}
+
+/* PMU SSI is the IP that maps the external PMU hi6553 registers as IO */
+static void hi6220_pmussi_init(void)
+{
+ uint32_t data;
+
+ /* Take PMUSSI out of reset */
+ writel(ALWAYSON_SC_PERIPH_RST4_DIS_PRESET_PMUSSI_N,
+ &ao_sc->rst4_dis);
+ do {
+ data = readl(&ao_sc->rst4_stat);
+ } while (data & ALWAYSON_SC_PERIPH_RST4_DIS_PRESET_PMUSSI_N);
+
+ /* set PMU SSI clock latency for read operation */
+ data = readl(&ao_sc->mcu_subsys_ctrl3);
+ data &= ~ALWAYSON_SC_MCU_SUBSYS_CTRL3_RCLK_MASK;
+ data |= ALWAYSON_SC_MCU_SUBSYS_CTRL3_RCLK_3;
+ writel(data, &ao_sc->mcu_subsys_ctrl3);
+
+ /* enable PMUSSI clock */
+ data = ALWAYSON_SC_PERIPH_CLK5_EN_PCLK_PMUSSI_CCPU |
+ ALWAYSON_SC_PERIPH_CLK5_EN_PCLK_PMUSSI_MCU;
+
+ hi6220_clk_enable(data, &ao_sc->clk5_en);
+
+ /* Output high to PMIC on PWR_HOLD_GPIO0_0 */
+ gpio_request(0, "PWR_HOLD_GPIO0_0");
+ gpio_direction_output(0, 1);
+}
+
+int misc_init_r(void)
+{
+ return 0;
+}
+
+int board_init(void)
+{
+ gd->flags = 0;
+
+ return 0;
+}
+
+#ifdef CONFIG_GENERIC_MMC
+
+static int init_dwmmc(void)
+{
+ int ret;
+
+#ifdef CONFIG_DWMMC
+
+ /* mmc0 clocks are already configured by ATF */
+ ret = hi6220_pinmux_config(PERIPH_ID_SDMMC0);
+ if (ret)
+ printf("%s: Error configuring pinmux for eMMC (%d)\n"
+ , __func__, ret);
+
+ ret |= hi6220_dwmci_add_port(0, HI6220_MMC0_BASE, 8);
+ if (ret)
+ printf("%s: Error adding eMMC port (%d)\n", __func__, ret);
+
+
+ /* take mmc1 (sd slot) out of reset, configure clocks and pinmuxing */
+ mmc1_init_pll();
+ mmc1_reset_clk();
+
+ ret |= hi6220_pinmux_config(PERIPH_ID_SDMMC1);
+ if (ret)
+ printf("%s: Error configuring pinmux for eMMC (%d)\n"
+ , __func__, ret);
+
+ config_sd_carddetect();
+
+ ret |= hi6220_dwmci_add_port(1, HI6220_MMC1_BASE, 4);
+ if (ret)
+ printf("%s: Error adding SD port (%d)\n", __func__, ret);
+
+#endif
+ return ret;
+}
+
+/* setup board specific PMIC */
+int power_init_board(void)
+{
+ /* init the hi6220 pmussi ip */
+ hi6220_pmussi_init();
+
+ power_hi6553_init((u8 *)HI6220_PMUSSI_BASE);
+
+ return 0;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ int ret;
+
+ /* add the eMMC and sd ports */
+ ret = init_dwmmc();
+
+ if (ret)
+ debug("init_dwmmc failed\n");
+
+ return ret;
+}
+#endif
+
+int dram_init(void)
+{
+ gd->ram_size = PHYS_SDRAM_1_SIZE;
+ return 0;
+}
+
+void dram_init_banksize(void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+}
+
+/* Use the Watchdog to cause reset */
+void reset_cpu(ulong addr)
+{
+ /* TODO program the watchdog */
+}
--- /dev/null
+/*
+ * (C) Copyright 2015 Linaro
+ *
+ * Peter Griffin <peter.griffin@linaro.org>
+ *
+ * Configuration for HiKey 96boards CE. Parts were derived from other ARM
+ * configurations.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __HIKEY_H
+#define __HIKEY_H
+
+/* We use generic board for hikey */
+#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_POWER
+#define CONFIG_POWER_HI6553
+
+#define CONFIG_REMAKE_ELF
+
+#define CONFIG_SUPPORT_RAW_INITRD
+
+/* Cache Definitions */
+#define CONFIG_SYS_DCACHE_OFF
+
+#define CONFIG_IDENT_STRING "hikey"
+
+/* Flat Device Tree Definitions */
+#define CONFIG_OF_LIBFDT
+
+/* Physical Memory Map */
+
+/* CONFIG_SYS_TEXT_BASE needs to align with where ATF loads bl33.bin */
+#define CONFIG_SYS_TEXT_BASE 0x35000000
+
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM_1 0x00000000
+
+/* 1008 MB (the last 16Mb are secured for TrustZone by ATF*/
+#define PHYS_SDRAM_1_SIZE 0x3f000000
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+
+#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
+
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x7fff0)
+
+#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x80000)
+
+/* Generic Timer Definitions */
+#define COUNTER_FREQUENCY 19000000
+
+/* Generic Interrupt Controller Definitions */
+#define GICD_BASE 0xf6801000
+#define GICC_BASE 0xf6802000
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (8 << 20))
+
+/* PL011 Serial Configuration */
+#define CONFIG_PL011_SERIAL
+
+#define CONFIG_PL011_CLOCK 19200000
+#define CONFIG_PL01x_PORTS {(void *)0xF8015000}
+#define CONFIG_CONS_INDEX 0
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_CMD_USB
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_DWC2
+#define CONFIG_USB_DWC2_REG_ADDR 0xF72C0000
+/*#define CONFIG_DWC2_DFLT_SPEED_FULL*/
+#define CONFIG_DWC2_ENABLE_DYNAMIC_FIFO
+
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_SMSC95XX
+#define CONFIG_USB_ETHER_ASIX
+#define CONFIG_MISC_INIT_R
+#endif
+
+#define CONFIG_HIKEY_GPIO
+#define CONFIG_DM_GPIO
+#define CONFIG_CMD_GPIO
+#define CONFIG_DM
+
+/* SD/MMC configuration */
+#define CONFIG_GENERIC_MMC
+#define CONFIG_MMC
+#define CONFIG_DWMMC
+#define CONFIG_HIKEY_DWMMC
+#define CONFIG_BOUNCE_BUFFER
+#define CONFIG_CMD_MMC
+
+#define CONFIG_FS_EXT4
+
+/* Command line configuration */
+#define CONFIG_MENU
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_UNZIP
+#define CONFIG_CMD_ENV
+
+#define CONFIG_MTD_PARTITIONS
+
+/* BOOTP options */
+#define CONFIG_BOOTP_BOOTFILESIZE
+
+#include <config_distro_defaults.h>
+
+/* Initial environment variables */
+
+/*
+ * Defines where the kernel and FDT will be put in RAM
+ */
+
+/* Assume we boot with root on the seventh partition of eMMC */
+#define CONFIG_BOOTARGS "console=ttyAMA0,115200n8 root=/dev/mmcblk0p9 rw"
+
+#define BOOT_TARGET_DEVICES(func) \
+ func(USB, usb, 0) \
+ func(MMC, mmc, 1) \
+ func(DHCP, dhcp, na)
+#include <config_distro_bootcmd.h>
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "kernel_name=Image\0" \
+ "kernel_addr_r=0x00080000\0" \
+ "fdt_name=hi6220-hikey.dtb\0" \
+ "fdt_addr_r=0x02000000\0" \
+ "fdt_high=0xffffffffffffffff\0" \
+ "initrd_high=0xffffffffffffffff\0" \
+ BOOTENV
+
+
+/* Preserve enviroment on sd card */
+#define CONFIG_COMMAND_HISTORY
+
+#define CONFIG_ENV_SIZE 0x1000
+#define CONFIG_ENV_IS_IN_FAT
+#define FAT_ENV_INTERFACE "mmc"
+#define FAT_ENV_DEVICE_AND_PART "1:1"
+#define FAT_ENV_FILE "uboot.env"
+#define CONFIG_FAT_WRITE
+#define CONFIG_ENV_VARS_UBOOT_CONFIG
+
+/* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_SYS_MAXARGS 64 /* max command args */
+
+#define CONFIG_SYS_NO_FLASH
+
+#endif /* __HIKEY_H */
projects / project / bcm63xx / u-boot.git / commitdiff