sky2: fix management of driver LED

Observed by Mike McCormack.

The LED bit here is just a software controlled value used to
turn on one of the LED's on some boards. The register value was wrong,
which could have been causing some power control issues.
Get rid of problematic define use the correct mask.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
index c7c0a5b7b53a1f718b22b8ff7bb461c01e1e1404..ba5180a2326456d8731fdd33e47494bf7323ef99 100644 (file)
--- a/drivers/net/sky2.c
+++ b/drivers/net/sky2.c
@@ -256,6 +256,9 @@ static void sky2_power_on(struct sky2_hw *hw)
 
                sky2_read32(hw, B2_GP_IO);
        }
+
+       /* Turn on "driver loaded" LED */
+       sky2_write16(hw, B0_CTST, Y2_LED_STAT_ON);
 }
 
 static void sky2_power_aux(struct sky2_hw *hw)
@@ -274,6 +277,9 @@ static void sky2_power_aux(struct sky2_hw *hw)
                sky2_write8(hw, B0_POWER_CTRL,
                            (PC_VAUX_ENA | PC_VCC_ENA |
                             PC_VAUX_ON | PC_VCC_OFF));
+
+       /* turn off "driver loaded LED" */
+       sky2_write16(hw, B0_CTST, Y2_LED_STAT_OFF);
 }
 
 static void sky2_gmac_reset(struct sky2_hw *hw, unsigned port)
@@ -1867,9 +1873,6 @@ static int sky2_down(struct net_device *dev)
        sky2_phy_power_down(hw, port);
        spin_unlock_bh(&sky2->phy_lock);
 
-       /* turn off LED's */
-       sky2_write16(hw, B0_Y2LED, LED_STAT_OFF);
-
        sky2_tx_reset(hw, port);
 
        /* Free any pending frames stuck in HW queue */
@@ -2983,8 +2986,6 @@ static void sky2_reset(struct sky2_hw *hw)
        sky2_write8(hw, B2_TI_CTRL, TIM_STOP);
        sky2_write8(hw, B2_TI_CTRL, TIM_CLR_IRQ);
 
-       sky2_write8(hw, B0_Y2LED, LED_STAT_ON);
-
        /* Turn off descriptor polling */
        sky2_write32(hw, B28_DPT_CTRL, DPT_STOP);
 
@@ -4601,7 +4602,6 @@ static void __devexit sky2_remove(struct pci_dev *pdev)
 
        sky2_power_aux(hw);
 
-       sky2_write16(hw, B0_Y2LED, LED_STAT_OFF);
        sky2_write8(hw, B0_CTST, CS_RST_SET);
        sky2_read8(hw, B0_CTST);
 

diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h
index 73c954712467eb6a0554176f068ffe2986da5d8a..34042ff7c121be8e8569e3b46a0b668054897953 100644 (file)
--- a/drivers/net/sky2.h
+++ b/drivers/net/sky2.h
@@ -155,7 +155,7 @@ enum pci_cfg_reg1 {
 enum csr_regs {
        B0_RAP          = 0x0000,
        B0_CTST         = 0x0004,
-       B0_Y2LED        = 0x0005,
+
        B0_POWER_CTRL   = 0x0007,
        B0_ISRC         = 0x0008,
        B0_IMSK         = 0x000c,
@@ -283,13 +283,6 @@ enum {
        CS_RST_SET      = 1,    /* Set   Software reset */
 };
 
-/*     B0_LED                   8 Bit  LED register */
-enum {
-/* Bit  7.. 2: reserved */
-       LED_STAT_ON     = 1<<1, /* Status LED on        */
-       LED_STAT_OFF    = 1,    /* Status LED off       */
-};
-
 /*     B0_POWER_CTRL    8 Bit  Power Control reg (YUKON only) */
 enum {
        PC_VAUX_ENA     = 1<<7, /* Switch VAUX Enable  */