+++ /dev/null
-#include "qcom-ipq8064-v1.0.dtsi"
-
-#include <dt-bindings/input/input.h>
-
-/ {
- model = "TP-Link Archer C2600";
- compatible = "tplink,c2600", "qcom,ipq8064";
-
- memory@0 {
- reg = <0x42000000 0x1e000000>;
- device_type = "memory";
- };
-
- reserved-memory {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- rsvd@41200000 {
- reg = <0x41200000 0x300000>;
- no-map;
- };
- };
-
- aliases {
- serial0 = &uart4;
- mdio-gpio0 = &mdio0;
-
- led-boot = &power;
- led-failsafe = &general;
- led-running = &power;
- led-upgrade = &general;
- };
-
- chosen {
- linux,stdout-path = "serial0:115200n8";
- };
-
- soc {
- pinmux@800000 {
- button_pins: button_pins {
- mux {
- pins = "gpio16", "gpio54", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- i2c4_pins: i2c4_pinmux {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio6", "gpio7", "gpio8", "gpio9", "gpio26", "gpio33",
- "gpio53", "gpio66";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19", "gpio21";
- function = "gsbi5";
- bias-pull-down;
- };
-
- data {
- pins = "gpio18", "gpio19";
- drive-strength = <10>;
- };
-
- cs {
- pins = "gpio20";
- function = "gpio";
- drive-strength = <10>;
- bias-pull-up;
- };
-
- clk {
- pins = "gpio21";
- drive-strength = <12>;
- };
- };
-
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "gpio";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- usb0_pwr_en_pin: usb0_pwr_en_pin {
- mux {
- pins = "gpio25";
- function = "gpio";
- drive-strength = <10>;
- bias-pull-up;
- output-high;
- };
- };
-
- usb1_pwr_en_pin: usb1_pwr_en_pin {
- mux {
- pins = "gpio23";
- function = "gpio";
- drive-strength = <10>;
- bias-pull-up;
- output-high;
- };
- };
- };
-
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "ok";
- serial@16340000 {
- status = "ok";
- };
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
- };
-
- gsbi5: gsbi@1a200000 {
- qcom,mode = <GSBI_PROT_SPI>;
- status = "ok";
-
- spi5: spi@1a280000 {
- status = "ok";
-
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
-
- flash: m25p80@0 {
- compatible = "jedec,spi-nor";
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <50000000>;
- reg = <0>;
-
- SBL1@0 {
- label = "SBL1";
- reg = <0x0 0x20000>;
- read-only;
- };
-
- MIBIB@20000 {
- label = "MIBIB";
- reg = <0x20000 0x20000>;
- read-only;
- };
-
- SBL2@40000 {
- label = "SBL2";
- reg = <0x40000 0x20000>;
- read-only;
- };
-
- SBL3@60000 {
- label = "SBL3";
- reg = <0x60000 0x30000>;
- read-only;
- };
-
- DDRCONFIG@90000 {
- label = "DDRCONFIG";
- reg = <0x90000 0x10000>;
- read-only;
- };
-
- SSD@a0000 {
- label = "SSD";
- reg = <0xa0000 0x10000>;
- read-only;
- };
-
- TZ@b0000 {
- label = "TZ";
- reg = <0xb0000 0x30000>;
- read-only;
- };
-
- RPM@e0000 {
- label = "RPM";
- reg = <0xe0000 0x20000>;
- read-only;
- };
-
- fs-uboot@100000 {
- label = "fs-uboot";
- reg = <0x100000 0x70000>;
- read-only;
- };
-
- uboot-env@170000 {
- label = "uboot-env";
- reg = <0x170000 0x40000>;
- read-only;
- };
-
- radio@1b0000 {
- label = "radio";
- reg = <0x1b0000 0x40000>;
- read-only;
- };
-
- os-image@1f0000 {
- label = "os-image";
- reg = <0x1f0000 0x200000>;
- };
-
- rootfs@3f0000 {
- label = "rootfs";
- reg = <0x3f0000 0x1b00000>;
- };
-
- defaultmac: default-mac@1ef0000 {
- label = "default-mac";
- reg = <0x1ef0000 0x00200>;
- read-only;
- };
-
- pin@1ef0200 {
- label = "pin";
- reg = <0x1ef0200 0x00200>;
- read-only;
- };
-
- product-info@1ef0400 {
- label = "product-info";
- reg = <0x1ef0400 0x0fc00>;
- read-only;
- };
-
- partition-table@1f00000 {
- label = "partition-table";
- reg = <0x1f00000 0x10000>;
- read-only;
- };
-
- soft-version@1f10000 {
- label = "soft-version";
- reg = <0x1f10000 0x10000>;
- read-only;
- };
-
- support-list@1f20000 {
- label = "support-list";
- reg = <0x1f20000 0x10000>;
- read-only;
- };
-
- profile@1f30000 {
- label = "profile";
- reg = <0x1f30000 0x10000>;
- read-only;
- };
-
- default-config@1f40000 {
- label = "default-config";
- reg = <0x1f40000 0x10000>;
- read-only;
- };
-
- user-config@1f50000 {
- label = "user-config";
- reg = <0x1f50000 0x40000>;
- read-only;
- };
-
- qos-db@1f90000 {
- label = "qos-db";
- reg = <0x1f90000 0x40000>;
- read-only;
- };
-
- usb-config@1fd0000 {
- label = "usb-config";
- reg = <0x1fd0000 0x10000>;
- read-only;
- };
-
- log@1fe0000 {
- label = "log";
- reg = <0x1fe0000 0x20000>;
- read-only;
- };
- };
- };
- };
-
- phy@100f8800 { /* USB3 port 1 HS phy */
- status = "ok";
- };
-
- phy@100f8830 { /* USB3 port 1 SS phy */
- status = "ok";
- };
-
- phy@110f8800 { /* USB3 port 0 HS phy */
- status = "ok";
- };
-
- phy@110f8830 { /* USB3 port 0 SS phy */
- status = "ok";
- };
-
- usb30@0 {
- status = "ok";
-
- pinctrl-0 = <&usb0_pwr_en_pin>;
- pinctrl-names = "default";
- };
-
- usb30@1 {
- status = "ok";
-
- pinctrl-0 = <&usb1_pwr_en_pin>;
- pinctrl-names = "default";
- };
-
- pcie0: pci@1b500000 {
- status = "ok";
- phy-tx0-term-offset = <7>;
- };
-
- pcie1: pci@1b700000 {
- status = "ok";
- phy-tx0-term-offset = <7>;
- };
-
- mdio0: mdio {
- compatible = "virtual,mdio-gpio";
- #address-cells = <1>;
- #size-cells = <0>;
- gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- phy0: ethernet-phy@0 {
- device_type = "ethernet-phy";
- reg = <0>;
- qca,ar8327-initvals = <
- 0x00004 0x7600000 /* PAD0_MODE */
- 0x00008 0x1000000 /* PAD5_MODE */
- 0x0000c 0x80 /* PAD6_MODE */
- 0x000e4 0x6a545 /* MAC_POWER_SEL */
- 0x000e0 0xc74164de /* SGMII_CTRL */
- 0x0007c 0x4e /* PORT0_STATUS */
- 0x00094 0x4e /* PORT6_STATUS */
- >;
- };
-
- phy4: ethernet-phy@4 {
- device_type = "ethernet-phy";
- reg = <4>;
- };
- };
-
- gmac1: ethernet@37200000 {
- status = "ok";
- phy-mode = "rgmii";
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- mtd-mac-address = <&defaultmac 0x8>;
- mtd-mac-address-increment = <1>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- gmac2: ethernet@37400000 {
- status = "ok";
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- mtd-mac-address = <&defaultmac 0x8>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- rpm@108000 {
- pinctrl-0 = <&i2c4_pins>;
- pinctrl-names = "default";
- };
- };
-
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- wifi {
- label = "wifi";
- gpios = <&qcom_pinmux 49 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RFKILL>;
- };
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- };
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- };
-
- ledswitch {
- label = "ledswitch";
- gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_LIGHTS_TOGGLE>;
- };
- };
-
- gpio-leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- lan {
- label = "c2600:white:lan";
- gpios = <&qcom_pinmux 6 GPIO_ACTIVE_HIGH>;
- };
-
- usb4 {
- label = "c2600:white:usb_4";
- gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
- };
-
- usb2 {
- label = "c2600:white:usb_2";
- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
- };
-
- wps {
- label = "c2600:white:wps";
- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
- };
-
- wan_amber {
- label = "c2600:amber:wan";
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
- };
-
- wan_white {
- label = "c2600:white:wan";
- gpios = <&qcom_pinmux 33 GPIO_ACTIVE_LOW>;
- };
-
- power: power {
- label = "c2600:white:power";
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
- default-state = "keep";
- };
-
- general: general {
- label = "c2600:white:general";
- gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-&adm_dma {
- status = "ok";
-};
+++ /dev/null
-#include "qcom-ipq8064-v1.0.dtsi"
-
-#include <dt-bindings/input/input.h>
-
-/ {
- model = "Netgear Nighthawk X4 D7800";
- compatible = "netgear,d7800", "qcom,ipq8064";
-
- memory@0 {
- reg = <0x42000000 0xe000000>;
- device_type = "memory";
- };
-
- reserved-memory {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- rsvd@41200000 {
- reg = <0x41200000 0x300000>;
- no-map;
- };
- };
-
- aliases {
- serial0 = &uart4;
- mdio-gpio0 = &mdio0;
-
- led-boot = &power_white;
- led-failsafe = &power_amber;
- led-running = &power_white;
- led-upgrade = &power_amber;
- };
-
- chosen {
- bootargs = "rootfstype=squashfs noinitrd";
- linux,stdout-path = "serial0:115200n8";
- };
-
- soc {
- pinmux@800000 {
- button_pins: button_pins {
- mux {
- pins = "gpio6", "gpio54", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- i2c4_pins: i2c4_pinmux {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
- "gpio24","gpio26", "gpio53", "gpio64";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "gpio";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- nand_pins: nand_pins {
- mux {
- pins = "gpio34", "gpio35", "gpio36",
- "gpio37", "gpio38", "gpio39",
- "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- function = "nand";
- drive-strength = <10>;
- bias-disable;
- };
- pullups {
- pins = "gpio39";
- bias-pull-up;
- };
- hold {
- pins = "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- bias-bus-hold;
- };
- };
-
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- usb0_pwr_en_pins: usb0_pwr_en_pins {
- mux {
- pins = "gpio15";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-high;
- };
- };
-
- usb1_pwr_en_pins: usb1_pwr_en_pins {
- mux {
- pins = "gpio16", "gpio68";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-high;
- };
- };
- };
-
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "ok";
- serial@16340000 {
- status = "ok";
- };
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
- };
-
- sata-phy@1b400000 {
- status = "ok";
- };
-
- sata@29000000 {
- status = "ok";
- };
-
- phy@100f8800 { /* USB3 port 1 HS phy */
- status = "ok";
- };
-
- phy@100f8830 { /* USB3 port 1 SS phy */
- status = "ok";
- };
-
- phy@110f8800 { /* USB3 port 0 HS phy */
- status = "ok";
- };
-
- phy@110f8830 { /* USB3 port 0 SS phy */
- status = "ok";
- };
-
- usb30@0 {
- status = "ok";
-
- pinctrl-0 = <&usb0_pwr_en_pins>;
- pinctrl-names = "default";
- };
-
- usb30@1 {
- status = "ok";
-
- pinctrl-0 = <&usb1_pwr_en_pins>;
- pinctrl-names = "default";
- };
-
- pcie0: pci@1b500000 {
- status = "ok";
- reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&pcie0_pins>;
- pinctrl-names = "default";
- };
-
- pcie1: pci@1b700000 {
- status = "ok";
- reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&pcie1_pins>;
- pinctrl-names = "default";
- };
-
- nand@1ac00000 {
- status = "ok";
-
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
-
- #address-cells = <1>;
- #size-cells = <1>;
-
- qcadata@0 {
- label = "qcadata";
- reg = <0x0000000 0x0c80000>;
- read-only;
- };
-
- APPSBL@c80000 {
- label = "APPSBL";
- reg = <0x0c80000 0x0500000>;
- read-only;
- };
-
- APPSBLENV@1180000 {
- label = "APPSBLENV";
- reg = <0x1180000 0x0080000>;
- read-only;
- };
-
- art: art@1200000 {
- label = "art";
- reg = <0x1200000 0x0140000>;
- read-only;
- };
-
- artbak: art@1340000 {
- label = "artbak";
- reg = <0x1340000 0x0140000>;
- read-only;
- };
-
- kernel@1480000 {
- label = "kernel";
- reg = <0x1480000 0x0200000>;
- };
-
- ubi@1680000 {
- label = "ubi";
- reg = <0x1680000 0x1E00000>;
- };
-
- netgear@3480000 {
- label = "netgear";
- reg = <0x3480000 0x4480000>;
- read-only;
- };
-
- reserve@7900000 {
- label = "reserve";
- reg = <0x7900000 0x0700000>;
- read-only;
- };
-
- firmware@1480000 {
- label = "firmware";
- reg = <0x1480000 0x2000000>;
- };
- };
-
- mdio0: mdio {
- compatible = "virtual,mdio-gpio";
- #address-cells = <1>;
- #size-cells = <0>;
- gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- phy0: ethernet-phy@0 {
- device_type = "ethernet-phy";
- reg = <0>;
- qca,ar8327-initvals = <
- 0x00004 0x7600000 /* PAD0_MODE */
- 0x00008 0x1000000 /* PAD5_MODE */
- 0x0000c 0x80 /* PAD6_MODE */
- 0x000e4 0x6a545 /* MAC_POWER_SEL */
- 0x000e0 0xc74164de /* SGMII_CTRL */
- 0x0007c 0x4e /* PORT0_STATUS */
- 0x00094 0x4e /* PORT6_STATUS */
- >;
- };
-
- phy4: ethernet-phy@4 {
- device_type = "ethernet-phy";
- reg = <4>;
- };
- };
-
- gmac1: ethernet@37200000 {
- status = "ok";
- phy-mode = "rgmii";
- phy-handle = <&phy4>;
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- mtd-mac-address = <&art 6>;
- };
-
- gmac2: ethernet@37400000 {
- status = "ok";
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- mtd-mac-address = <&art 0>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- rpm@108000 {
- pinctrl-0 = <&i2c4_pins>;
- pinctrl-names = "default";
- };
- };
-
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- wifi {
- label = "wifi";
- gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RFKILL>;
- };
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- };
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- };
- };
-
- gpio-leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- usb1 {
- label = "d7800:white:usb1";
- gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
- };
-
- usb2 {
- label = "d7800:white:usb2";
- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
- };
-
- power_amber: power_amber {
- label = "d7800:amber:power";
- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
- };
-
- wan_white {
- label = "d7800:white:wan";
- gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
- };
-
- wan_amber {
- label = "d7800:amber:wan";
- gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
- };
-
- wps {
- label = "d7800:white:wps";
- gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
- };
-
- esata {
- label = "d7800:white:esata";
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
- };
-
- power_white: power_white {
- label = "d7800:white:power";
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
- default-state = "keep";
- };
-
- wifi {
- label = "d7800:white:wifi";
- gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-&adm_dma {
- status = "ok";
-};
+++ /dev/null
-#include "qcom-ipq8064-v1.0.dtsi"
-
-#include <dt-bindings/input/input.h>
-
-/ {
- model = "Linksys EA8500 WiFi Router";
- compatible = "linksys,ea8500", "qcom,ipq8064";
-
- memory@0 {
- reg = <0x42000000 0x1e000000>;
- device_type = "memory";
- };
-
- reserved-memory {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- rsvd@41200000 {
- reg = <0x41200000 0x300000>;
- no-map;
- };
- };
-
- aliases {
- serial0 = &uart4;
- mdio-gpio0 = &mdio0;
-
- led-boot = &power;
- led-failsafe = &power;
- led-running = &power;
- led-upgrade = &power;
- };
-
- chosen {
- bootargs = "console=ttyMSM0,115200n8";
- linux,stdout-path = "serial0:115200n8";
- append-rootblock = "ubi.mtd="; /* append to bootargs adding the root deviceblock nbr from bootloader */
- };
-
- soc {
- pinmux@800000 {
- button_pins: button_pins {
- mux {
- pins = "gpio65", "gpio67", "gpio68";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- i2c4_pins: i2c4_pinmux {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio6", "gpio53", "gpio54";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "gpio";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- nand_pins: nand_pins {
- mux {
- pins = "gpio34", "gpio35", "gpio36",
- "gpio37", "gpio38", "gpio39",
- "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- function = "nand";
- drive-strength = <10>;
- bias-disable;
- };
- pullups {
- pins = "gpio39";
- bias-pull-up;
- };
- hold {
- pins = "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- bias-bus-hold;
- };
- };
-
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
- };
- };
-
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "ok";
- serial@16340000 {
- status = "ok";
- };
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
- };
-
- sata-phy@1b400000 {
- status = "ok";
- };
-
- sata@29000000 {
- status = "ok";
- };
-
- phy@100f8800 { /* USB3 port 1 HS phy */
- status = "ok";
- };
-
- phy@100f8830 { /* USB3 port 1 SS phy */
- status = "ok";
- };
-
- phy@110f8800 { /* USB3 port 0 HS phy */
- status = "ok";
- };
-
- phy@110f8830 { /* USB3 port 0 SS phy */
- status = "ok";
- };
-
- usb30@0 {
- status = "ok";
- };
-
- usb30@1 {
- status = "ok";
- };
-
- pcie0: pci@1b500000 {
- status = "ok";
- phy-tx0-term-offset = <7>;
- };
-
- pcie1: pci@1b700000 {
- status = "ok";
- phy-tx0-term-offset = <7>;
- };
-
- pcie2: pci@1b900000 {
- status = "ok";
- phy-tx0-term-offset = <7>;
- };
-
- nand@1ac00000 {
- status = "ok";
-
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
-
- #address-cells = <1>;
- #size-cells = <1>;
-
- SBL1@0 {
- label = "SBL1";
- reg = <0x0000000 0x0040000>;
- read-only;
- };
-
- MIBIB@40000 {
- label = "MIBIB";
- reg = <0x0040000 0x0140000>;
- read-only;
- };
-
- SBL2@180000 {
- label = "SBL2";
- reg = <0x0180000 0x0140000>;
- read-only;
- };
-
- SBL3@2c0000 {
- label = "SBL3";
- reg = <0x02c0000 0x0280000>;
- read-only;
- };
-
- DDRCONFIG@540000 {
- label = "DDRCONFIG";
- reg = <0x0540000 0x0120000>;
- read-only;
- };
-
- SSD@660000 {
- label = "SSD";
- reg = <0x0660000 0x0120000>;
- read-only;
- };
-
- TZ@780000 {
- label = "TZ";
- reg = <0x0780000 0x0280000>;
- read-only;
- };
-
- RPM@a00000 {
- label = "RPM";
- reg = <0x0a00000 0x0280000>;
- read-only;
- };
-
- art: art@c80000 {
- label = "art";
- reg = <0x0c80000 0x0140000>;
- read-only;
- };
-
- APPSBL@dc0000 {
- label = "APPSBL";
- reg = <0x0dc0000 0x0100000>;
- read-only;
- };
-
- u_env@ec0000 {
- label = "u_env";
- reg = <0x0ec0000 0x0040000>;
- };
-
- s_env@f00000 {
- label = "s_env";
- reg = <0x0f00000 0x0040000>;
- };
-
- devinfo@f40000 {
- label = "devinfo";
- reg = <0x0f40000 0x0040000>;
- };
-
- linux@f80000 {
- label = "kernel1";
- reg = <0x0f80000 0x2800000>; /* 3 MB spill to rootfs*/
- };
-
- rootfs@1280000 {
- label = "rootfs1";
- reg = <0x1280000 0x2500000>;
- };
-
- linux2@3780000 {
- label = "kernel2";
- reg = <0x3780000 0x2800000>;
- };
-
- rootfs2@3a80000 {
- label = "rootfs2";
- reg = <0x3a80000 0x2500000>;
- };
-
- syscfg@5f80000 {
- label = "syscfg";
- reg = <0x5f80000 0x2080000>;
- };
- };
-
- mdio0: mdio {
- compatible = "virtual,mdio-gpio";
- #address-cells = <1>;
- #size-cells = <0>;
- gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- phy0: ethernet-phy@0 {
- device_type = "ethernet-phy";
- reg = <0>;
- qca,ar8327-initvals = <
- 0x00004 0x7600000 /* PAD0_MODE */
- 0x00008 0x1000000 /* PAD5_MODE */
- 0x0000c 0x80 /* PAD6_MODE */
- 0x000e4 0x6a545 /* MAC_POWER_SEL */
- 0x000e0 0xc74164de /* SGMII_CTRL */
- 0x0007c 0x4e /* PORT0_STATUS */
- 0x00094 0x4e /* PORT6_STATUS */
- >;
- };
-
- phy4: ethernet-phy@4 {
- device_type = "ethernet-phy";
- reg = <4>;
- };
- };
-
- gmac1: ethernet@37200000 {
- status = "ok";
- phy-mode = "rgmii";
- qcom,id = <1>;
- qcom,phy_mdio_addr = <4>;
- qcom,poll_required = <1>;
- qcom,rgmii_delay = <0>;
- qcom,emulation = <0>;
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- //lan
- gmac2: ethernet@37400000 {
- status = "ok";
- phy-mode = "sgmii";
- qcom,id = <2>;
- qcom,phy_mdio_addr = <0>; /* none */
- qcom,poll_required = <0>; /* no polling */
- qcom,rgmii_delay = <0>;
- qcom,emulation = <0>;
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- rpm@108000 {
- pinctrl-0 = <&i2c4_pins>;
- pinctrl-names = "default";
- };
-
- adm_dma: dma@18300000 {
- status = "ok";
- };
- };
-
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- wifi {
- label = "wifi";
- gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RFKILL>;
- };
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART >;
- };
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- };
- };
-
- gpio-leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- wps {
- label = "ea8500:green:wps";
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
- };
-
- power: power {
- label = "ea8500:white:power";
- gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
- default-state = "keep";
- };
-
- wifi {
- label = "ea8500:green:wifi";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_HIGH>;
- };
- };
-};
+++ /dev/null
-#include "qcom-ipq8064-v1.0.dtsi"
-
-#include <dt-bindings/input/input.h>
-
-/ {
- model = "Netgear Nighthawk X4 R7500";
- compatible = "netgear,r7500", "qcom,ipq8064";
-
- memory@0 {
- reg = <0x42000000 0xe000000>;
- device_type = "memory";
- };
-
- reserved-memory {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- rsvd@41200000 {
- reg = <0x41200000 0x300000>;
- no-map;
- };
- };
-
- aliases {
- serial0 = &uart4;
- mdio-gpio0 = &mdio0;
-
- led-boot = &power_white;
- led-failsafe = &power_amber;
- led-running = &power_white;
- led-upgrade = &power_amber;
- };
-
- chosen {
- bootargs = "rootfstype=squashfs noinitrd";
- linux,stdout-path = "serial0:115200n8";
- };
-
- soc {
- pinmux@800000 {
- button_pins: button_pins {
- mux {
- pins = "gpio6", "gpio54", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- i2c4_pins: i2c4_pinmux {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
- "gpio24","gpio26", "gpio53", "gpio64";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "gpio";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- nand_pins: nand_pins {
- mux {
- pins = "gpio34", "gpio35", "gpio36",
- "gpio37", "gpio38", "gpio39",
- "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- function = "nand";
- drive-strength = <10>;
- bias-disable;
- };
- pullups {
- pins = "gpio39";
- bias-pull-up;
- };
- hold {
- pins = "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- bias-bus-hold;
- };
- };
-
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
- };
- };
-
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "ok";
- serial@16340000 {
- status = "ok";
- };
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
- };
-
- sata-phy@1b400000 {
- status = "ok";
- };
-
- sata@29000000 {
- status = "ok";
- };
-
- phy@100f8800 { /* USB3 port 1 HS phy */
- status = "ok";
- };
-
- phy@100f8830 { /* USB3 port 1 SS phy */
- status = "ok";
- };
-
- phy@110f8800 { /* USB3 port 0 HS phy */
- status = "ok";
- };
-
- phy@110f8830 { /* USB3 port 0 SS phy */
- status = "ok";
- };
-
- usb30@0 {
- status = "ok";
- };
-
- usb30@1 {
- status = "ok";
- };
-
- pcie0: pci@1b500000 {
- status = "ok";
- };
-
- pcie1: pci@1b700000 {
- status = "ok";
- };
-
- nand@1ac00000 {
- status = "ok";
-
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
-
- #address-cells = <1>;
- #size-cells = <1>;
-
- qcadata@0 {
- label = "qcadata";
- reg = <0x0000000 0x0c80000>;
- read-only;
- };
-
- APPSBL@c80000 {
- label = "APPSBL";
- reg = <0x0c80000 0x0500000>;
- read-only;
- };
-
- APPSBLENV@1180000 {
- label = "APPSBLENV";
- reg = <0x1180000 0x0080000>;
- read-only;
- };
-
- art: art@1200000 {
- label = "art";
- reg = <0x1200000 0x0140000>;
- read-only;
- };
-
- kernel@1340000 {
- label = "kernel";
- reg = <0x1340000 0x0200000>;
- };
-
- ubi@1540000 {
- label = "ubi";
- reg = <0x1540000 0x1800000>;
- };
-
- netgear@2d40000 {
- label = "netgear";
- reg = <0x2d40000 0x0c00000>;
- read-only;
- };
-
- reserve@3940000 {
- label = "reserve";
- reg = <0x3940000 0x46c0000>;
- read-only;
- };
-
- firmware@1340000 {
- label = "firmware";
- reg = <0x1340000 0x1a00000>;
- };
-
- };
-
- mdio0: mdio {
- compatible = "virtual,mdio-gpio";
- #address-cells = <1>;
- #size-cells = <0>;
- gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- phy0: ethernet-phy@0 {
- device_type = "ethernet-phy";
- reg = <0>;
- qca,ar8327-initvals = <
- 0x00004 0x7600000 /* PAD0_MODE */
- 0x00008 0x1000000 /* PAD5_MODE */
- 0x0000c 0x80 /* PAD6_MODE */
- 0x000e4 0x6a545 /* MAC_POWER_SEL */
- 0x000e0 0xc74164de /* SGMII_CTRL */
- 0x0007c 0x4e /* PORT0_STATUS */
- 0x00094 0x4e /* PORT6_STATUS */
- >;
- };
-
- phy4: ethernet-phy@4 {
- device_type = "ethernet-phy";
- reg = <4>;
- };
- };
-
- gmac1: ethernet@37200000 {
- status = "ok";
- phy-mode = "rgmii";
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- mtd-mac-address = <&art 6>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- gmac2: ethernet@37400000 {
- status = "ok";
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- mtd-mac-address = <&art 0>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- rpm@108000 {
- pinctrl-0 = <&i2c4_pins>;
- pinctrl-names = "default";
- };
- };
-
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- wifi {
- label = "wifi";
- gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RFKILL>;
- };
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- };
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- };
- };
-
- gpio-leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- usb1 {
- label = "r7500:white:usb1";
- gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
- };
-
- usb2 {
- label = "r7500:white:usb2";
- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
- };
-
- power_amber: power_amber {
- label = "r7500:amber:power";
- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
- };
-
- wan_white {
- label = "r7500:white:wan";
- gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
- };
-
- wan_amber {
- label = "r7500:amber:wan";
- gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
- };
-
- wps {
- label = "r7500:white:wps";
- gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
- };
-
- esata {
- label = "r7500:white:esata";
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
- };
-
- power_white: power_white {
- label = "r7500:white:power";
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
- default-state = "keep";
- };
-
- wifi {
- label = "r7500:white:wifi";
- gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-&adm_dma {
- status = "ok";
-};
+++ /dev/null
-#include "qcom-ipq8064-v1.0.dtsi"
-
-#include <dt-bindings/input/input.h>
-
-/ {
- model = "Netgear Nighthawk X4 R7500v2";
- compatible = "netgear,r7500v2", "qcom,ipq8064";
-
- memory@0 {
- reg = <0x42000000 0x1e000000>;
- device_type = "memory";
- };
-
- reserved-memory {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- rsvd@41200000 {
- reg = <0x41200000 0x300000>;
- no-map;
- };
-
- rsvd@5fe00000 {
- reg = <0x5fe00000 0x200000>;
- reusable;
- };
- };
-
- aliases {
- serial0 = &uart4;
- mdio-gpio0 = &mdio0;
-
- led-boot = &power;
- led-failsafe = &power;
- led-running = &power;
- led-upgrade = &power;
- };
-
- chosen {
- bootargs = "rootfstype=squashfs noinitrd";
- linux,stdout-path = "serial0:115200n8";
- };
-
- soc {
- pinmux@800000 {
- button_pins: button_pins {
- mux {
- pins = "gpio6", "gpio54", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- i2c4_pins: i2c4_pinmux {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
- "gpio24","gpio26", "gpio53", "gpio64";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "gpio";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- nand_pins: nand_pins {
- mux {
- pins = "gpio34", "gpio35", "gpio36",
- "gpio37", "gpio38", "gpio39",
- "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- function = "nand";
- drive-strength = <10>;
- bias-disable;
- };
- pullups {
- pins = "gpio39";
- bias-pull-up;
- };
- hold {
- pins = "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- bias-bus-hold;
- };
- };
-
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- usb0_pwr_en_pins: usb0_pwr_en_pins {
- mux {
- pins = "gpio15";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-high;
- };
- };
-
- usb1_pwr_en_pins: usb1_pwr_en_pins {
- mux {
- pins = "gpio16", "gpio68";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-high;
- };
- };
- };
-
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "ok";
- serial@16340000 {
- status = "ok";
- };
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
- };
-
- sata-phy@1b400000 {
- status = "ok";
- };
-
- sata@29000000 {
- status = "ok";
- };
-
- phy@100f8800 { /* USB3 port 1 HS phy */
- status = "ok";
- };
-
- phy@100f8830 { /* USB3 port 1 SS phy */
- status = "ok";
- };
-
- phy@110f8800 { /* USB3 port 0 HS phy */
- status = "ok";
- };
-
- phy@110f8830 { /* USB3 port 0 SS phy */
- status = "ok";
- };
-
- usb30@0 {
- status = "ok";
-
- pinctrl-0 = <&usb0_pwr_en_pins>;
- pinctrl-names = "default";
- };
-
- usb30@1 {
- status = "ok";
-
- pinctrl-0 = <&usb1_pwr_en_pins>;
- pinctrl-names = "default";
- };
-
- pcie0: pci@1b500000 {
- status = "ok";
- reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
- pinctrl-0 = <&pcie0_pins>;
- pinctrl-names = "default";
- };
-
- pcie1: pci@1b700000 {
- status = "ok";
- reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
- pinctrl-0 = <&pcie1_pins>;
- pinctrl-names = "default";
- };
-
- nand@1ac00000 {
- status = "ok";
-
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
-
- #address-cells = <1>;
- #size-cells = <1>;
-
- qcadata@0 {
- label = "qcadata";
- reg = <0x0000000 0x0c80000>;
- read-only;
- };
-
- APPSBL@c80000 {
- label = "APPSBL";
- reg = <0x0c80000 0x0500000>;
- read-only;
- };
-
- APPSBLENV@1180000 {
- label = "APPSBLENV";
- reg = <0x1180000 0x0080000>;
- read-only;
- };
-
- art: art@1200000 {
- label = "art";
- reg = <0x1200000 0x0140000>;
- read-only;
- };
-
- artbak: art@1340000 {
- label = "artbak";
- reg = <0x1340000 0x0140000>;
- read-only;
- };
-
- kernel@1480000 {
- label = "kernel";
- reg = <0x1480000 0x0200000>;
- };
-
- ubi@1680000 {
- label = "ubi";
- reg = <0x1680000 0x1E00000>;
- };
-
- netgear@3480000 {
- label = "netgear";
- reg = <0x3480000 0x4480000>;
- read-only;
- };
-
- reserve@7900000 {
- label = "reserve";
- reg = <0x7900000 0x0700000>;
- read-only;
- };
-
- firmware@1480000 {
- label = "firmware";
- reg = <0x1480000 0x2000000>;
- };
-
- };
-
- mdio0: mdio {
- compatible = "virtual,mdio-gpio";
- #address-cells = <1>;
- #size-cells = <0>;
- gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- phy0: ethernet-phy@0 {
- device_type = "ethernet-phy";
- reg = <0>;
- qca,ar8327-initvals = <
- 0x00004 0x7600000 /* PAD0_MODE */
- 0x00008 0x1000000 /* PAD5_MODE */
- 0x0000c 0x80 /* PAD6_MODE */
- 0x000e4 0xaa545 /* MAC_POWER_SEL */
- 0x000e0 0xc74164de /* SGMII_CTRL */
- 0x0007c 0x4e /* PORT0_STATUS */
- 0x00094 0x4e /* PORT6_STATUS */
- >;
- };
-
- phy4: ethernet-phy@4 {
- device_type = "ethernet-phy";
- reg = <4>;
- };
- };
-
- gmac1: ethernet@37200000 {
- status = "ok";
- phy-mode = "rgmii";
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- mtd-mac-address = <&art 6>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- gmac2: ethernet@37400000 {
- status = "ok";
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- mtd-mac-address = <&art 0>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- rpm@108000 {
- pinctrl-0 = <&i2c4_pins>;
- pinctrl-names = "default";
- };
- };
-
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- wifi {
- label = "wifi";
- gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RFKILL>;
- };
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- };
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- };
- };
-
- gpio-leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- usb1 {
- label = "r7500v2:amber:usb1";
- gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
- };
-
- usb3 {
- label = "r7500v2:amber:usb3";
- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
- };
-
- status {
- label = "r7500v2:amber:status";
- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
- };
-
- internet {
- label = "r7500v2:white:internet";
- gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
- };
-
- wan {
- label = "r7500v2:white:wan";
- gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
- };
-
- wps {
- label = "r7500v2:white:wps";
- gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
- };
-
- esata {
- label = "r7500v2:white:esata";
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
- };
-
- power: power {
- label = "r7500v2:white:power";
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
- default-state = "keep";
- };
-
- wifi {
- label = "r7500v2:white:wifi";
- gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-&adm_dma {
- status = "ok";
-};
+++ /dev/null
-#include "qcom-ipq8064-v1.0.dtsi"
-
-#include <dt-bindings/input/input.h>
-
-/ {
- model = "TP-Link Archer VR2600v";
- compatible = "tplink,vr2600v", "qcom,ipq8064";
-
- memory@0 {
- reg = <0x42000000 0x1e000000>;
- device_type = "memory";
- };
-
- reserved-memory {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- rsvd@41200000 {
- reg = <0x41200000 0x300000>;
- no-map;
- };
- };
-
- aliases {
- serial0 = &uart4;
- mdio-gpio0 = &mdio0;
-
- led-boot = &power;
- led-failsafe = &general;
- led-running = &power;
- led-upgrade = &general;
- };
-
- chosen {
- linux,stdout-path = "serial0:115200n8";
- };
-
- soc {
- pinmux@800000 {
- led_pins: led_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio17",
- "gpio26", "gpio53", "gpio56", "gpio66";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- i2c4_pins: i2c4_pinmux {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- button_pins: button_pins {
- mux {
- pins = "gpio54", "gpio64", "gpio65", "gpio67", "gpio68";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19", "gpio21";
- function = "gsbi5";
- bias-pull-down;
- };
-
- data {
- pins = "gpio18", "gpio19";
- drive-strength = <10>;
- };
-
- cs {
- pins = "gpio20";
- drive-strength = <10>;
- bias-pull-up;
- };
-
- clk {
- pins = "gpio21";
- drive-strength = <12>;
- };
- };
-
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "gpio";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
- };
- };
-
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "ok";
- serial@16340000 {
- status = "ok";
- };
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
- };
-
- gsbi5: gsbi@1a200000 {
- qcom,mode = <GSBI_PROT_SPI>;
- status = "ok";
-
- spi4: spi@1a280000 {
- status = "ok";
-
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
-
- flash: W25Q128@0 {
- compatible = "jedec,spi-nor";
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <50000000>;
- reg = <0>;
-
- SBL1@0 {
- label = "SBL1";
- reg = <0x0 0x20000>;
- read-only;
- };
-
- MIBIB@20000 {
- label = "MIBIB";
- reg = <0x20000 0x20000>;
- read-only;
- };
-
- SBL2@40000 {
- label = "SBL2";
- reg = <0x40000 0x40000>;
- read-only;
- };
-
- SBL3@80000 {
- label = "SBL3";
- reg = <0x80000 0x80000>;
- read-only;
- };
-
- DDRCONFIG@100000 {
- label = "DDRCONFIG";
- reg = <0x100000 0x10000>;
- read-only;
- };
-
- SSD@110000 {
- label = "SSD";
- reg = <0x110000 0x10000>;
- read-only;
- };
-
- TZ@120000 {
- label = "TZ";
- reg = <0x120000 0x80000>;
- read-only;
- };
-
- RPM@1a0000 {
- label = "RPM";
- reg = <0x1a0000 0x80000>;
- read-only;
- };
-
- APPSBL@220000 {
- label = "APPSBL";
- reg = <0x220000 0x80000>;
- read-only;
- };
-
- APPSBLENV@2a0000 {
- label = "APPSBLENV";
- reg = <0x2a0000 0x40000>;
- read-only;
- };
-
- OLDART@2e0000 {
- label = "OLDART";
- reg = <0x2e0000 0x40000>;
- read-only;
- };
-
- kernel@320000 {
- label = "kernel";
- reg = <0x320000 0x200000>;
- };
-
- rootfs@520000 {
- label = "rootfs";
- reg = <0x520000 0xa60000>;
- };
-
- defaultmac: default-mac@0xfaf100 {
- label = "default-mac";
- reg = <0xfaf100 0x00200>;
- read-only;
- };
-
- ART@fc0000 {
- label = "ART";
- reg = <0xfc0000 0x40000>;
- read-only;
- };
- };
- };
- };
-
- phy@100f8800 { /* USB3 port 1 HS phy */
- status = "ok";
- };
-
- phy@100f8830 { /* USB3 port 1 SS phy */
- status = "ok";
- };
-
- phy@110f8800 { /* USB3 port 0 HS phy */
- status = "ok";
- };
-
- phy@110f8830 { /* USB3 port 0 SS phy */
- status = "ok";
- };
-
- usb30@0 {
- status = "ok";
- };
-
- usb30@1 {
- status = "ok";
- };
-
- pcie0: pci@1b500000 {
- status = "ok";
- phy-tx0-term-offset = <7>;
- };
-
- pcie1: pci@1b700000 {
- status = "ok";
- phy-tx0-term-offset = <7>;
- };
-
- mdio0: mdio {
- compatible = "virtual,mdio-gpio";
- #address-cells = <1>;
- #size-cells = <0>;
- gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- phy0: ethernet-phy@0 {
- device_type = "ethernet-phy";
- reg = <0>;
- qca,ar8327-initvals = <
- 0x00004 0x7600000 /* PAD0_MODE */
- 0x00008 0x1000000 /* PAD5_MODE */
- 0x0000c 0x80 /* PAD6_MODE */
- 0x000e4 0x6a545 /* MAC_POWER_SEL */
- 0x000e0 0xc74164de /* SGMII_CTRL */
- 0x0007c 0x4e /* PORT0_STATUS */
- 0x00094 0x4e /* PORT6_STATUS */
- >;
- };
-
- phy4: ethernet-phy@4 {
- device_type = "ethernet-phy";
- reg = <4>;
- };
- };
-
- gmac1: ethernet@37200000 {
- status = "ok";
- phy-mode = "rgmii";
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- mtd-mac-address = <&defaultmac 0>;
- mtd-mac-address-increment = <1>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- gmac2: ethernet@37400000 {
- status = "ok";
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- mtd-mac-address = <&defaultmac 0>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- rpm@108000 {
- pinctrl-0 = <&i2c4_pins>;
- pinctrl-names = "default";
- };
- };
-
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- wifi {
- label = "wifi";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RFKILL>;
- };
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- };
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- };
-
- dect {
- label = "dect";
- gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_PHONE>;
- };
-
- ledswitch {
- label = "ledswitch";
- gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_LIGHTS_TOGGLE>;
- };
- };
-
- gpio-leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- dsl {
- label = "vr2600v:white:dsl";
- gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
- };
-
- usb {
- label = "vr2600v:white:usb";
- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
- };
-
- lan {
- label = "vr2600v:white:lan";
- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
- };
-
- wlan2g {
- label = "vr2600v:white:wlan2g";
- gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
- };
-
- wlan5g {
- label = "vr2600v:white:wlan5g";
- gpios = <&qcom_pinmux 17 GPIO_ACTIVE_HIGH>;
- };
-
- power: power {
- label = "vr2600v:white:power";
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
- default-state = "keep";
- };
-
- phone {
- label = "vr2600v:white:phone";
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
- };
-
- wan {
- label = "vr2600v:white:wan";
- gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>;
- };
-
- general: general {
- label = "vr2600v:white:general";
- gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-&adm_dma {
- status = "ok";
-};
+++ /dev/null
-#include "qcom-ipq8065-v1.0.dtsi"
-
-#include <dt-bindings/input/input.h>
-
-/ {
- model = "ZyXEL NBG6817";
- compatible = "zyxel,nbg6817", "qcom,ipq8065";
-
- memory@0 {
- reg = <0x42000000 0x1e000000>;
- device_type = "memory";
- };
-
- reserved-memory {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- rsvd@41200000 {
- reg = <0x41200000 0x300000>;
- no-map;
- };
- };
-
- aliases {
- serial0 = &uart4;
- mdio-gpio0 = &mdio0;
- sdcc1 = &sdcc1;
-
- led-boot = &power;
- led-failsafe = &power;
- led-running = &power;
- led-upgrade = &power;
- };
-
- chosen {
- bootargs = "root=/dev/mmcblk0p5 rootfstype=squashfs,ext4 rootwait noinitrd";
- linux,stdout-path = "serial0:115200n8";
- };
-
- soc {
- pinmux@800000 {
- button_pins: button_pins {
- mux {
- pins = "gpio6", "gpio54", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- i2c4_pins: i2c4_pinmux {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio9", "gpio26", "gpio33", "gpio64";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-down;
- };
- };
-
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "gpio";
- drive-strength = <8>;
- bias-disable;
- };
-
- clk {
- pins = "gpio1";
- input-disable;
- };
- };
-
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
-
- tx {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ;
- input-disable;
- };
- };
-
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19", "gpio21";
- function = "gsbi5";
- drive-strength = <10>;
- bias-none;
- };
-
- cs {
- pins = "gpio20";
- drive-strength = <12>;
- };
- };
-
- usb0_pwr_en_pins: usb0_pwr_en_pins {
- mux {
- pins = "gpio16", "gpio17";
- function = "gpio";
- drive-strength = <12>;
- };
-
- pwr {
- pins = "gpio17";
- bias-pull-down;
- output-high;
- };
-
- ovc {
- pins = "gpio16";
- bias-pull-up;
- };
- };
-
- usb1_pwr_en_pins: usb1_pwr_en_pins {
- mux {
- pins = "gpio14", "gpio15";
- function = "gpio";
- drive-strength = <12>;
- };
-
- pwr {
- pins = "gpio14";
- bias-pull-down;
- output-high;
- };
-
- ovc {
- pins = "gpio15";
- bias-pull-up;
- };
- };
- };
-
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "ok";
- serial@16340000 {
- status = "ok";
- };
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
- };
-
- gsbi5: gsbi@1a200000 {
- qcom,mode = <GSBI_PROT_SPI>;
- status = "ok";
-
- spi4: spi@1a280000 {
- status = "ok";
-
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
-
- flash: m25p80@0 {
- compatible = "jedec,spi-nor";
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <51200000>;
- reg = <0>;
-
- linux,part-probe = "qcom-smem";
- };
- };
- };
-
- phy@100f8800 { /* USB3 port 1 HS phy */
- status = "ok";
- };
-
- phy@100f8830 { /* USB3 port 1 SS phy */
- status = "ok";
- };
-
- phy@110f8800 { /* USB3 port 0 HS phy */
- status = "ok";
- };
-
- phy@110f8830 { /* USB3 port 0 SS phy */
- status = "ok";
- };
-
- usb30@0 {
- status = "ok";
-
- pinctrl-0 = <&usb0_pwr_en_pins>;
- pinctrl-names = "default";
- };
-
- usb30@1 {
- status = "ok";
-
- pinctrl-0 = <&usb1_pwr_en_pins>;
- pinctrl-names = "default";
- };
-
- pcie0: pci@1b500000 {
- status = "ok";
- reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
- pinctrl-0 = <&pcie0_pins>;
- pinctrl-names = "default";
- };
-
- pcie1: pci@1b700000 {
- status = "ok";
- reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
- pinctrl-0 = <&pcie1_pins>;
- pinctrl-names = "default";
- };
-
- mdio0: mdio {
- compatible = "virtual,mdio-gpio";
- #address-cells = <1>;
- #size-cells = <0>;
- gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- phy0: ethernet-phy@0 {
- device_type = "ethernet-phy";
- reg = <0>;
- qca,ar8327-initvals = <
- 0x00004 0x7600000 /* PAD0_MODE */
- 0x00008 0x1000000 /* PAD5_MODE */
- 0x0000c 0x80 /* PAD6_MODE */
- 0x000e4 0xaa545 /* MAC_POWER_SEL */
- 0x000e0 0xc74164de /* SGMII_CTRL */
- 0x0007c 0x4e /* PORT0_STATUS */
- 0x00094 0x4e /* PORT6_STATUS */
- 0x00970 0x1e864443 /* QM_PORT0_CTRL0 */
- 0x00974 0x000001c6 /* QM_PORT0_CTRL1 */
- 0x00978 0x19008643 /* QM_PORT1_CTRL0 */
- 0x0097c 0x000001c6 /* QM_PORT1_CTRL1 */
- 0x00980 0x19008643 /* QM_PORT2_CTRL0 */
- 0x00984 0x000001c6 /* QM_PORT2_CTRL1 */
- 0x00988 0x19008643 /* QM_PORT3_CTRL0 */
- 0x0098c 0x000001c6 /* QM_PORT3_CTRL1 */
- 0x00990 0x19008643 /* QM_PORT4_CTRL0 */
- 0x00994 0x000001c6 /* QM_PORT4_CTRL1 */
- 0x00998 0x1e864443 /* QM_PORT5_CTRL0 */
- 0x0099c 0x000001c6 /* QM_PORT5_CTRL1 */
- 0x009a0 0x1e864443 /* QM_PORT6_CTRL0 */
- 0x009a4 0x000001c6 /* QM_PORT6_CTRL1 */
- >;
- };
-
- phy4: ethernet-phy@4 {
- device_type = "ethernet-phy";
- reg = <4>;
- qca,ar8327-initvals = <
- 0x000e4 0x6a545 /* MAC_POWER_SEL */
- 0x0000c 0x80 /* PAD6_MODE */
- >;
- };
- };
-
- gmac1: ethernet@37200000 {
- status = "ok";
- phy-mode = "rgmii";
- qcom,id = <1>;
- qcom,phy_mdio_addr = <4>;
- qcom,poll_required = <0>;
- qcom,rgmii_delay = <1>;
- qcom,phy_mii_type = <0>;
- qcom,emulation = <0>;
- qcom,irq = <255>;
- mdiobus = <&mdio0>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- gmac2: ethernet@37400000 {
- status = "ok";
- phy-mode = "sgmii";
- qcom,id = <2>;
- qcom,phy_mdio_addr = <0>; /* none */
- qcom,poll_required = <0>; /* no polling */
- qcom,rgmii_delay = <0>;
- qcom,phy_mii_type = <1>;
- qcom,emulation = <0>;
- qcom,irq = <258>;
- mdiobus = <&mdio0>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- rpm@108000 {
- pinctrl-0 = <&i2c4_pins>;
- pinctrl-names = "default";
- };
-
- amba {
- sdcc1: sdcc@12400000 {
- status = "okay";
- };
- };
- };
-
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- wifi {
- label = "wifi";
- gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RFKILL>;
- };
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- };
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- };
- };
-
- gpio-leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- internet {
- label = "nbg6817:white:internet";
- gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
- };
-
- power: power {
- label = "nbg6817:white:power";
- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
- default-state = "keep";
- };
-
- wifi2g {
- label = "nbg6817:amber:wifi2g";
- gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
- };
-
- /* wifi2g amber from the manual is missing */
-
- wifi5g {
- label = "nbg6817:amber:wifi5g";
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
- };
-
- /* wifi5g amber from the manual is missing */
- };
-};
-
-&adm_dma {
- status = "ok";
-};
+++ /dev/null
-#include "qcom-ipq8065-v1.0.dtsi"
-
-#include <dt-bindings/input/input.h>
-
-/ {
- model = "Netgear Nighthawk X4S R7800";
- compatible = "netgear,r7800", "qcom,ipq8065", "qcom,ipq8064";
-
- memory@0 {
- reg = <0x42000000 0x1e000000>;
- device_type = "memory";
- };
-
- reserved-memory {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- rsvd@41200000 {
- reg = <0x41200000 0x300000>;
- no-map;
- };
-
- rsvd@5fe00000 {
- reg = <0x5fe00000 0x200000>;
- reusable;
- };
- };
-
- aliases {
- serial0 = &uart4;
- mdio-gpio0 = &mdio0;
-
- led-boot = &power_white;
- led-failsafe = &power_amber;
- led-running = &power_white;
- led-upgrade = &power_amber;
- };
-
- chosen {
- linux,stdout-path = "serial0:115200n8";
- };
-
- soc {
- pinmux@800000 {
- button_pins: button_pins {
- mux {
- pins = "gpio6", "gpio54", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- i2c4_pins: i2c4_pinmux {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- led_pins: led_pins {
- pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
- "gpio24","gpio26", "gpio53", "gpio64";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-down;
- };
-
- nand_pins: nand_pins {
- mux {
- pins = "gpio34", "gpio35", "gpio36",
- "gpio37", "gpio38", "gpio39",
- "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- function = "nand";
- drive-strength = <10>;
- bias-disable;
- };
- pullups {
- pins = "gpio39";
- bias-pull-up;
- };
- hold {
- pins = "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- bias-bus-hold;
- };
- };
-
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "gpio";
- drive-strength = <8>;
- bias-disable;
- };
-
- clk {
- pins = "gpio1";
- input-disable;
- };
- };
-
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
-
- tx {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ;
- input-disable;
- };
- };
-
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19", "gpio21";
- function = "gsbi5";
- bias-pull-down;
- };
-
- data {
- pins = "gpio18", "gpio19";
- drive-strength = <10>;
- };
-
- cs {
- pins = "gpio20";
- drive-strength = <10>;
- bias-pull-up;
- };
-
- clk {
- pins = "gpio21";
- drive-strength = <12>;
- };
- };
-
- spi6_pins: spi6_pins {
- mux {
- pins = "gpio55", "gpio56", "gpio58";
- function = "gsbi6";
- bias-pull-down;
- };
-
- mosi {
- pins = "gpio55";
- drive-strength = <12>;
- };
-
- miso {
- pins = "gpio56";
- drive-strength = <14>;
- };
-
- cs {
- pins = "gpio57";
- drive-strength = <12>;
- bias-pull-up;
- };
-
- clk {
- pins = "gpio58";
- drive-strength = <12>;
- };
-
- reset {
- pins = "gpio33";
- drive-strength = <10>;
- bias-pull-down;
- output-high;
- };
- };
-
- usb0_pwr_en_pins: usb0_pwr_en_pins {
- mux {
- pins = "gpio15";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-high;
- };
- };
-
- usb1_pwr_en_pins: usb1_pwr_en_pins {
- mux {
- pins = "gpio16", "gpio68";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-high;
- };
- };
- };
-
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "ok";
- serial@16340000 {
- status = "ok";
- };
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
- };
-
- gsbi5: gsbi@1a200000 {
- qcom,mode = <GSBI_PROT_SPI>;
- status = "ok";
-
- spi5: spi@1a280000 {
- status = "ok";
-
- pinctrl-0 = <&spi_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
-
- flash: m25p80@0 {
- compatible = "jedec,spi-nor";
- #address-cells = <1>;
- #size-cells = <1>;
- spi-max-frequency = <50000000>;
- reg = <0>;
-
- linux,part-probe = "qcom-smem";
- };
- };
- };
-
- gsbi6: gsbi@16500000 {
- qcom,mode = <GSBI_PROT_SPI>;
- status = "ok";
- spi6: spi@16580000 {
- status = "ok";
-
- pinctrl-0 = <&spi6_pins>;
- pinctrl-names = "default";
-
- cs-gpios = <&qcom_pinmux 57 GPIO_ACTIVE_HIGH>;
-
- spi-nor@0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <6000000>;
- };
- };
- };
-
- sata-phy@1b400000 {
- status = "ok";
- };
-
- sata@29000000 {
- ports-implemented = <0x1>;
- status = "ok";
- };
-
- phy@100f8800 { /* USB3 port 1 HS phy */
- status = "ok";
- };
-
- phy@100f8830 { /* USB3 port 1 SS phy */
- status = "ok";
- };
-
- phy@110f8800 { /* USB3 port 0 HS phy */
- status = "ok";
- };
-
- phy@110f8830 { /* USB3 port 0 SS phy */
- status = "ok";
- };
-
- usb30@0 {
- status = "ok";
-
- pinctrl-0 = <&usb0_pwr_en_pins>;
- pinctrl-names = "default";
- };
-
- usb30@1 {
- status = "ok";
-
- pinctrl-0 = <&usb1_pwr_en_pins>;
- pinctrl-names = "default";
- };
-
- pcie0: pci@1b500000 {
- status = "ok";
- phy-tx0-term-offset = <7>;
- };
-
- pcie1: pci@1b700000 {
- status = "ok";
- phy-tx0-term-offset = <7>;
- };
-
- nand@1ac00000 {
- status = "ok";
-
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
-
- nand-ecc-strength = <4>;
- nand-ecc-step-size = <512>;
- nand-bus-width = <8>;
-
- #address-cells = <1>;
- #size-cells = <1>;
-
- qcadata@0 {
- label = "qcadata";
- reg = <0x0000000 0x0c80000>;
- read-only;
- };
-
- APPSBL@c80000 {
- label = "APPSBL";
- reg = <0x0c80000 0x0500000>;
- read-only;
- };
-
- APPSBLENV@1180000 {
- label = "APPSBLENV";
- reg = <0x1180000 0x0080000>;
- read-only;
- };
-
- art: art@1200000 {
- label = "art";
- reg = <0x1200000 0x0140000>;
- read-only;
- };
-
- artbak: art@1340000 {
- label = "artbak";
- reg = <0x1340000 0x0140000>;
- read-only;
- };
-
- kernel@1480000 {
- label = "kernel";
- reg = <0x1480000 0x0200000>;
- };
-
- ubi@1680000 {
- label = "ubi";
- reg = <0x1680000 0x1E00000>;
- };
-
- netgear@3480000 {
- label = "netgear";
- reg = <0x3480000 0x4480000>;
- read-only;
- };
-
- reserve@7900000 {
- label = "reserve";
- reg = <0x7900000 0x0700000>;
- read-only;
- };
-
- firmware@1480000 {
- label = "firmware";
- reg = <0x1480000 0x2000000>;
- };
- };
-
- mdio0: mdio {
- compatible = "virtual,mdio-gpio";
- #address-cells = <1>;
- #size-cells = <0>;
- gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
-
- phy0: ethernet-phy@0 {
- device_type = "ethernet-phy";
- reg = <0>;
- qca,ar8327-initvals = <
- 0x00004 0x7600000 /* PAD0_MODE */
- 0x00008 0x1000000 /* PAD5_MODE */
- 0x0000c 0x80 /* PAD6_MODE */
- 0x000e4 0xaa545 /* MAC_POWER_SEL */
- 0x000e0 0xc74164de /* SGMII_CTRL */
- 0x0007c 0x4e /* PORT0_STATUS */
- 0x00094 0x4e /* PORT6_STATUS */
- 0x00970 0x1e864443 /* QM_PORT0_CTRL0 */
- 0x00974 0x000001c6 /* QM_PORT0_CTRL1 */
- 0x00978 0x19008643 /* QM_PORT1_CTRL0 */
- 0x0097c 0x000001c6 /* QM_PORT1_CTRL1 */
- 0x00980 0x19008643 /* QM_PORT2_CTRL0 */
- 0x00984 0x000001c6 /* QM_PORT2_CTRL1 */
- 0x00988 0x19008643 /* QM_PORT3_CTRL0 */
- 0x0098c 0x000001c6 /* QM_PORT3_CTRL1 */
- 0x00990 0x19008643 /* QM_PORT4_CTRL0 */
- 0x00994 0x000001c6 /* QM_PORT4_CTRL1 */
- 0x00998 0x1e864443 /* QM_PORT5_CTRL0 */
- 0x0099c 0x000001c6 /* QM_PORT5_CTRL1 */
- 0x009a0 0x1e864443 /* QM_PORT6_CTRL0 */
- 0x009a4 0x000001c6 /* QM_PORT6_CTRL1 */
- >;
- qca,ar8327-vlans = <
- 0x1 0x5e /* VLAN1 Ports 1/2/3/4/6 */
- 0x2 0x21 /* VLAN2 Ports 0/5 */
- >;
- };
-
- phy4: ethernet-phy@4 {
- device_type = "ethernet-phy";
- reg = <4>;
- qca,ar8327-initvals = <
- 0x000e4 0x6a545 /* MAC_POWER_SEL */
- 0x0000c 0x80 /* PAD6_MODE */
- >;
- };
- };
-
- gmac1: ethernet@37200000 {
- status = "ok";
- phy-mode = "rgmii";
- qcom,id = <1>;
- qcom,phy_mdio_addr = <4>;
- qcom,poll_required = <0>;
- qcom,rgmii_delay = <1>;
- qcom,phy_mii_type = <0>;
- qcom,emulation = <0>;
- qcom,irq = <255>;
- mdiobus = <&mdio0>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- mtd-mac-address = <&art 6>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- gmac2: ethernet@37400000 {
- status = "ok";
- phy-mode = "sgmii";
- qcom,id = <2>;
- qcom,phy_mdio_addr = <0>; /* none */
- qcom,poll_required = <0>; /* no polling */
- qcom,rgmii_delay = <0>;
- qcom,phy_mii_type = <1>;
- qcom,emulation = <0>;
- qcom,irq = <258>;
- mdiobus = <&mdio0>;
-
- mtd-mac-address = <&art 0>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- rpm@108000 {
- pinctrl-0 = <&i2c4_pins>;
- pinctrl-names = "default";
- };
- };
-
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- wifi {
- label = "wifi";
- gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RFKILL>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- debounce-interval = <60>;
- wakeup-source;
- };
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-
- gpio-leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- power_white: power_white {
- label = "r7800:white:power";
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
- default-state = "keep";
- };
-
- power_amber: power_amber {
- label = "r7800:amber:power";
- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
- };
-
- wan_white {
- label = "r7800:white:wan";
- gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
- };
-
- wan_amber {
- label = "r7800:amber:wan";
- gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
- };
-
- usb1 {
- label = "r7800:white:usb1";
- gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
- };
-
- usb2 {
- label = "r7800:white:usb2";
- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
- };
-
- esata {
- label = "r7800:white:esata";
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
- };
-
- wifi {
- label = "r7800:white:wifi";
- gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
- };
-
- wps {
- label = "r7800:white:wps";
- gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-&adm_dma {
- status = "ok";
-};
+++ /dev/null
-#include "qcom-ipq8065.dtsi"
+++ /dev/null
-#include "qcom-ipq8064.dtsi"
-
-/ {
- model = "Qualcomm IPQ8065";
- compatible = "qcom,ipq8065", "qcom,ipq8064";
-
- qcom,pvs {
- qcom,pvs-format-a;
- qcom,speed0-pvs0-bin-v0 =
- < 1725000000 1262500 >,
- < 1400000000 1175000 >,
- < 1000000000 1100000 >,
- < 800000000 1050000 >,
- < 600000000 1000000 >,
- < 384000000 975000 >;
- qcom,speed0-pvs1-bin-v0 =
- < 1725000000 1225000 >,
- < 1400000000 1150000 >,
- < 1000000000 1075000 >,
- < 800000000 1025000 >,
- < 600000000 975000 >,
- < 384000000 950000 >;
- qcom,speed0-pvs2-bin-v0 =
- < 1725000000 1200000 >,
- < 1400000000 1125000 >,
- < 1000000000 1050000 >,
- < 800000000 1000000 >,
- < 600000000 950000 >,
- < 384000000 925000 >;
- qcom,speed0-pvs3-bin-v0 =
- < 1725000000 1175000 >,
- < 1400000000 1100000 >,
- < 1000000000 1025000 >,
- < 800000000 975000 >,
- < 600000000 925000 >,
- < 384000000 900000 >;
- qcom,speed0-pvs4-bin-v0 =
- < 1725000000 1150000 >,
- < 1400000000 1075000 >,
- < 1000000000 1000000 >,
- < 800000000 950000 >,
- < 600000000 900000 >,
- < 384000000 875000 >;
- qcom,speed0-pvs5-bin-v0 =
- < 1725000000 1100000 >,
- < 1400000000 1025000 >,
- < 1000000000 950000 >,
- < 800000000 900000 >,
- < 600000000 850000 >,
- < 384000000 825000 >;
- qcom,speed0-pvs6-bin-v0 =
- < 1725000000 1050000 >,
- < 1400000000 975000 >,
- < 1000000000 900000 >,
- < 800000000 850000 >,
- < 600000000 800000 >,
- < 384000000 775000 >;
- };
-
- soc: soc {
-
- rpm@108000 {
-
- regulators {
-
- smb208_s2a: s2a {
- regulator-min-microvolt = <775000>;
- regulator-max-microvolt = <1275000>;
- };
-
- smb208_s2b: s2b {
- regulator-min-microvolt = <775000>;
- regulator-max-microvolt = <1275000>;
- };
- };
- };
-
- /* Temporary fixed regulator */
- vsdcc_fixed: vsdcc-regulator {
- compatible = "regulator-fixed";
- regulator-name = "SDCC Power";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- sdcc1bam:dma@12402000 {
- compatible = "qcom,bam-v1.3.0";
- reg = <0x12402000 0x8000>;
- interrupts = <0 98 0>;
- clocks = <&gcc SDC1_H_CLK>;
- clock-names = "bam_clk";
- #dma-cells = <1>;
- qcom,ee = <0>;
- };
-
- sdcc3bam:dma@12182000 {
- compatible = "qcom,bam-v1.3.0";
- reg = <0x12182000 0x8000>;
- interrupts = <0 96 0>;
- clocks = <&gcc SDC3_H_CLK>;
- clock-names = "bam_clk";
- #dma-cells = <1>;
- qcom,ee = <0>;
- };
-
- amba {
- compatible = "arm,amba-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- sdcc1: sdcc@12400000 {
- status = "disabled";
- compatible = "arm,pl18x", "arm,primecell";
- arm,primecell-periphid = <0x00051180>;
- reg = <0x12400000 0x2000>;
- interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "cmd_irq";
- clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
- clock-names = "mclk", "apb_pclk";
- bus-width = <8>;
- max-frequency = <96000000>;
- non-removable;
- cap-sd-highspeed;
- cap-mmc-highspeed;
- vmmc-supply = <&vsdcc_fixed>;
- dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
- dma-names = "tx", "rx";
- };
-
- sdcc3: sdcc@12180000 {
- compatible = "arm,pl18x", "arm,primecell";
- arm,primecell-periphid = <0x00051180>;
- status = "disabled";
- reg = <0x12180000 0x2000>;
- interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "cmd_irq";
- clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
- clock-names = "mclk", "apb_pclk";
- bus-width = <8>;
- cap-sd-highspeed;
- cap-mmc-highspeed;
- max-frequency = <192000000>;
- #mmc-ddr-1_8v;
- sd-uhs-sdr104;
- sd-uhs-ddr50;
- vqmmc-supply = <&vsdcc_fixed>;
- dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
- dma-names = "tx", "rx";
- };
- };
- };
-};
projects / openwrt / staging / nbd.git / commitdiff