phy: Update PHY power control sequence

All PHYs should be powered on before register configuration starts. And
only PCIe PHYs need an extra power control before deasserts reset state.

Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index 7932931a3da30069710bd9c08fb09cfe08df3a45..a55cfa4554a00b7b41142a843630bc6a3c66e945 100644 (file)
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -935,10 +935,12 @@ static void qcom_qmp_phy_configure(void __iomem *base,
        }
 }
 
-static int qcom_qmp_phy_com_init(struct qcom_qmp *qmp)
+static int qcom_qmp_phy_com_init(struct qmp_phy *qphy)
 {
+       struct qcom_qmp *qmp = qphy->qmp;
        const struct qmp_phy_cfg *cfg = qmp->cfg;
        void __iomem *serdes = qmp->serdes;
+       void __iomem *pcs = qphy->pcs;
        void __iomem *dp_com = qmp->dp_com;
        int ret, i;
 
@@ -979,10 +981,6 @@ static int qcom_qmp_phy_com_init(struct qcom_qmp *qmp)
                goto err_rst;
        }
 
-       if (cfg->has_phy_com_ctrl)
-               qphy_setbits(serdes, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL],
-                            SW_PWRDN);
-
        if (cfg->has_phy_dp_com_ctrl) {
                qphy_setbits(dp_com, QPHY_V3_DP_COM_POWER_DOWN_CTRL,
                             SW_PWRDN);
@@ -1000,6 +998,12 @@ static int qcom_qmp_phy_com_init(struct qcom_qmp *qmp)
                             SW_USB3PHY_RESET_MUX | SW_USB3PHY_RESET);
        }
 
+       if (cfg->has_phy_com_ctrl)
+               qphy_setbits(serdes, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL],
+                            SW_PWRDN);
+       else
+               qphy_setbits(pcs, QPHY_POWER_DOWN_CONTROL, cfg->pwrdn_ctrl);
+
        /* Serdes configuration */
        qcom_qmp_phy_configure(serdes, cfg->regs, cfg->serdes_tbl,
                               cfg->serdes_tbl_num);
@@ -1090,7 +1094,7 @@ static int qcom_qmp_phy_init(struct phy *phy)
 
        dev_vdbg(qmp->dev, "Initializing QMP phy\n");
 
-       ret = qcom_qmp_phy_com_init(qmp);
+       ret = qcom_qmp_phy_com_init(qphy);
        if (ret)
                return ret;
 
@@ -1127,7 +1131,8 @@ static int qcom_qmp_phy_init(struct phy *phy)
         * Pull out PHY from POWER DOWN state.
         * This is active low enable signal to power-down PHY.
         */
-       qphy_setbits(pcs, QPHY_POWER_DOWN_CONTROL, cfg->pwrdn_ctrl);
+       if(cfg->type == PHY_TYPE_PCIE)
+               qphy_setbits(pcs, QPHY_POWER_DOWN_CONTROL, cfg->pwrdn_ctrl);
 
        if (cfg->has_pwrdn_delay)
                usleep_range(cfg->pwrdn_delay_min, cfg->pwrdn_delay_max);