--- /dev/null
+/*
+ * Buffalo WZR-HP-G300NH2 board support
+ *
+ * Copyright (C) 2011 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2011 Mark Deneen <mdeneen@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+
+#include <asm/mips_machine.h>
+#include <asm/mach-ar71xx/ar71xx.h>
+#include <asm/mach-ar71xx/gpio.h>
+
+#include "machtype.h"
+#include "devices.h"
+#include "dev-ap91-pci.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-m25p80.h"
+#include "dev-usb.h"
+
+
+#define WZRHPG300NH2_MAC_OFFSET 0x20c
+#define WZRHPG300NH2_KEYS_POLL_INTERVAL 20 /* msecs */
+#define WZRHPG300NH2_KEYS_DEBOUNCE_INTERVAL (3 * WZRHPG300NH2_KEYS_POLL_INTERVAL)
+
+#ifdef CONFIG_MTD_PARTITIONS
+static struct mtd_partition wzrhpg300nh2_flash_partitions[] = {
+ {
+ .name = "u-boot",
+ .offset = 0,
+ .size = 0x0040000,
+ .mask_flags = MTD_WRITEABLE,
+ }, {
+ .name = "u-boot-env",
+ .offset = 0x0040000,
+ .size = 0x0010000,
+ .mask_flags = MTD_WRITEABLE,
+ }, {
+ .name = "art",
+ .offset = 0x0050000,
+ .size = 0x0010000,
+ .mask_flags = MTD_WRITEABLE,
+ }, {
+ .name = "kernel",
+ .offset = 0x0060000,
+ .size = 0x0100000,
+ }, {
+ .name = "rootfs",
+ .offset = 0x0160000,
+ .size = 0x1e90000,
+ }, {
+ .name = "user_property",
+ .offset = 0x1ff0000,
+ .size = 0x0010000,
+ .mask_flags = MTD_WRITEABLE,
+ }, {
+ .name = "firmware",
+ .offset = 0x0060000,
+ .size = 0x1f90000,
+ }
+};
+
+#endif /* CONFIG_MTD_PARTITIONS */
+
+
+
+static struct flash_platform_data wzrhpg300nh2_flash_data = {
+#ifdef CONFIG_MTD_PARTITIONS
+ .parts = wzrhpg300nh2_flash_partitions,
+ .nr_parts = ARRAY_SIZE(wzrhpg300nh2_flash_partitions),
+#endif
+};
+
+
+static struct gpio_led wzrhpg300nh2_leds_gpio[] __initdata = {
+ {
+ .name = "buffalo:red:diag",
+ .gpio = 16,
+ .active_low = 1,
+ },
+};
+
+static struct gpio_led wzrhpg300nh2_wmac_leds_gpio[] = {
+ {
+ .name = "buffalo:blue:usb",
+ .gpio = 4,
+ .active_low = 1,
+ },
+ {
+ .name = "buffalo:green:wireless",
+ .gpio = 5,
+ .active_low = 1,
+ },
+ {
+ .name = "buffalo:orange:security",
+ .gpio = 6,
+ .active_low = 1,
+ },
+ {
+ .name = "buffalo:green:router",
+ .gpio = 7,
+ .active_low = 1,
+ },
+ {
+ .name = "buffalo:blue:movie_engine_on",
+ .gpio = 8,
+ .active_low = 1,
+ },
+ {
+ .name = "buffalo:blue:movie_engine_off",
+ .gpio = 9,
+ .active_low = 1,
+ },
+};
+
+/* The AOSS button is wmac gpio 12 */
+static struct gpio_keys_button wzrhpg300nh2_gpio_keys[] __initdata = {
+ {
+ .desc = "reset",
+ .type = EV_KEY,
+ .code = KEY_RESTART,
+ .debounce_interval = WZRHPG300NH2_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = 1,
+ .active_low = 1,
+ }, {
+ .desc = "usb",
+ .type = EV_KEY,
+ .code = BTN_2,
+ .debounce_interval = WZRHPG300NH2_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = 7,
+ .active_low = 1,
+ }, {
+ .desc = "qos",
+ .type = EV_KEY,
+ .code = BTN_3,
+ .debounce_interval = WZRHPG300NH2_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = 11,
+ .active_low = 0,
+ }, {
+ .desc = "router_on",
+ .type = EV_KEY,
+ .code = BTN_5,
+ .debounce_interval = WZRHPG300NH2_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = 8,
+ .active_low = 0,
+ },
+};
+
+
+static void __init wzrhpg300nh2_setup(void)
+{
+
+ u8 *eeprom = (u8 *) KSEG1ADDR(0x1f051000);
+ u8 *mac0 = eeprom + WZRHPG300NH2_MAC_OFFSET;
+ /* There is an eth1 but it is not connected to the switch */
+
+ ar71xx_add_device_m25p80_multi(&wzrhpg300nh2_flash_data);
+
+ ar71xx_init_mac(ar71xx_eth0_data.mac_addr, mac0, 0);
+ ar71xx_add_device_mdio(0, ~(BIT(0)));
+
+ ar71xx_init_mac(ar71xx_eth0_data.mac_addr, mac0, 0);
+ ar71xx_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
+ ar71xx_eth0_data.speed = SPEED_1000;
+ ar71xx_eth0_data.duplex = DUPLEX_FULL;
+ ar71xx_eth0_data.phy_mask = BIT(0);
+
+ ar71xx_add_device_eth(0);
+ ar71xx_add_device_usb();
+ /* gpio13 is usb power. Turn it on. */
+ gpio_request(13, "usb");
+ gpio_direction_output(13, 1);
+
+ ar71xx_add_device_leds_gpio(-1, ARRAY_SIZE(wzrhpg300nh2_leds_gpio),
+ wzrhpg300nh2_leds_gpio);
+ ar71xx_register_gpio_keys_polled(-1, WZRHPG300NH2_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(wzrhpg300nh2_gpio_keys),
+ wzrhpg300nh2_gpio_keys);
+ ap91_pci_setup_wmac_led_pin(22);
+ ap91_pci_setup_wmac_leds(wzrhpg300nh2_wmac_leds_gpio,
+ ARRAY_SIZE(wzrhpg300nh2_wmac_leds_gpio));
+
+ ap91_pci_init(eeprom, mac0);
+}
+
+MIPS_MACHINE(AR71XX_MACH_WZR_HP_AG300H, "WZR-HP-G300NH2",
+ "Buffalo WZR-HP-G300NH2", wzrhpg300nh2_setup);
+
$(call Image/Build/Template/$(fs_128k)/$(1),WZRHPG30XNH,wzr-hp-g300nh,$(wzrhpg300nh_cmdline),WZR-HP-G300NH)
endef
+wzrhpg300nh2_cmdline=board=WZR-HP-G300NH2 console=ttyS0,115200
+define Image/Build/Profile/WZRHPG300NH2
+ $(call Image/Build/Template/$(fs_128k)/$(1),WZRHPG30XNH,wzr-hp-g300nh2,$(wzrhpg300nh2_cmdline),WZR-HP-G300NH2)
+endef
+
wzrhpag300h_cmdline=board=WZR-HP-AG300H console=ttyS0,115200
define Image/Build/Profile/WZRHPAG300H
$(call Image/Build/Template/$(fs_128k)/$(1),WZRHPG30XNH,wzr-hp-ag300h,$(wzrhpag300h_cmdline),WZR-HP-AG300H)
$(call Image/Build/Profile/WHRHPG300N,$(1))
$(call Image/Build/Profile/WHRHPGN,$(1))
$(call Image/Build/Profile/WZRHPG300NH,$(1))
+ $(call Image/Build/Profile/WZRHPG300NH2,$(1))
$(call Image/Build/Profile/WZRHPAG300H,$(1))
$(call Image/Build/Profile/WZRHPG450H,$(1))
$(call Image/Build/Profile/ZCN1523H28,$(1))
projects / openwrt / staging / hauke.git / commitdiff