ath79: add support for TP-Link MR-3040 v2

Add support for the ar71xx supported TP-Link MR-3040 v2.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>

diff --git a/target/linux/ath79/base-files/etc/board.d/01_leds b/target/linux/ath79/base-files/etc/board.d/01_leds
index 0d8222f650c1ba3f0d16a9f2e44962cff4057211..a42bde530f5ec9753e817d8a6d5fba43bb2cb560 100755 (executable)
--- a/target/linux/ath79/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/base-files/etc/board.d/01_leds
@@ -53,7 +53,8 @@ tplink,re450-v2)
        ucidef_set_led_netdev "lan_data" "LAN Data" "tp-link:green:lan_data" "eth0" "tx rx"
        ucidef_set_led_netdev "lan_link" "LAN Link" "tp-link:green:lan_link" "eth0" "link"
        ;;
-tplink,tl-mr3020-v1)
+tplink,tl-mr3020-v1|\
+tplink,tl-mr3040-v2)
        ucidef_set_led_netdev "lan" "LAN" "tp-link:green:lan" "eth0"
        ;;
 tplink,tl-wr1043nd-v4)

diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network
index 5ff4b192fcf54833fe7c0cf91abbd9d66e4c02c0..202c9bb8eb225de0f3721a8539b8d7cd3cf8efb0 100755 (executable)
--- a/target/linux/ath79/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/base-files/etc/board.d/02_network
@@ -17,6 +17,7 @@ ath79_setup_interfaces()
        tplink,re450-v2|\
        tplink,tl-mr10u|\
        tplink,tl-mr3020-v1|\
+       tplink,tl-mr3040-v2|\
        tplink,tl-wr703n|\
        ubnt,unifiac-lite|\
        ubnt,unifiac-mesh|\

diff --git a/target/linux/ath79/dts/ar9331_tplink_tl-mr3040-v2.dts b/target/linux/ath79/dts/ar9331_tplink_tl-mr3040-v2.dts
new file mode 100644 (file)
index 0000000..ff7ed9f
--- /dev/null
+++ b/target/linux/ath79/dts/ar9331_tplink_tl-mr3040-v2.dts
@@ -0,0 +1,165 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar9331.dtsi"
+
+/ {
+       model = "TP-Link TL-MR3040 V2";
+       compatible = "tplink,tl-mr3040-v2", "qca,ar9331";
+
+       aliases {
+               led-boot = &led_lan;
+               led-failsafe = &led_lan;
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               wlan {
+                       label = "tp-link:green:wlan";
+                       gpios = <&gpio 26 GPIO_ACTIVE_LOW>;
+                       default-state = "off";
+                       linux,default-trigger = "phy0tpt";
+               };
+
+               led_lan: lan {
+                       label = "tp-link:green:lan";
+                       gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+                       default-state = "off";
+               };
+
+               led3g {
+                       label = "tp-link:green:3g";
+                       gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
+                       default-state = "off";
+                       trigger-sources = <&hub_port>;
+                       linux,default-trigger = "usbport";
+               };
+       };
+
+       keys {
+               compatible = "gpio-keys-polled";
+               poll-interval = <20>;
+
+               reset {
+                       label = "reset";
+                       linux,code = <KEY_RESTART>;
+                       gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
+                       debounce-interval = <60>;
+               };
+
+               sw1 {
+                       label = "sw1";
+                       linux,input-type = <EV_SW>;
+                       linux,code = <BTN_0>;
+                       gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
+                       debounce-interval = <60>;
+               };
+
+               sw2 {
+                       label = "sw2";
+                       linux,input-type = <EV_SW>;
+                       linux,code = <BTN_1>;
+                       gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
+                       debounce-interval = <60>;
+               };
+       };
+
+       reg_usb_vbus: reg_usb_vbus {
+               compatible = "regulator-fixed";
+               regulator-name = "usb_vbus";
+               regulator-min-microvolt = <5000000>;
+               regulator-max-microvolt = <5000000>;
+               gpio = <&gpio 18 GPIO_ACTIVE_HIGH>;
+               enable-active-high;
+       };
+};
+
+&ref {
+       clock-frequency = <25000000>;
+};
+
+&uart {
+       status = "okay";
+};
+
+&gpio {
+       status = "okay";
+};
+
+&usb {
+       #address-cells = <1>;
+       #size-cells = <0>;
+       dr_mode = "host";
+       vbus-supply = <&reg_usb_vbus>;
+       status = "okay";
+
+       hub_port: port@1 {
+               reg = <1>;
+               #trigger-source-cells = <0>;
+       };
+};
+
+&usb_phy {
+       status = "okay";
+};
+
+&spi {
+       num-chipselects = <1>;
+       status = "okay";
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               spi-max-frequency = <104000000>;
+               reg = <0>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       uboot:  partition@0 {
+                               label = "u-boot";
+                               reg = <0x000000 0x020000>;
+                               read-only;
+                       };
+
+                       partition@20000 {
+                               label = "firmware";
+                               reg = <0x020000 0x3d0000>;
+                       };
+
+                       art: partition@3f0000 {
+                               label = "art";
+                               reg = <0x3f0000 0x010000>;
+                               read-only;
+                       };
+               };
+       };
+};
+
+&eth0 {
+       status = "okay";
+
+       mtd-mac-address = <&uboot 0x1fc00>;
+       gmac-config {
+               device = <&gmac>;
+
+               switch-phy-addr-swap = <0>;
+               switch-phy-swap = <0>;
+       };
+};
+
+&eth1 {
+       status = "okay";
+       compatible = "syscon", "simple-mfd";
+};
+
+&wmac {
+       status = "okay";
+       mtd-cal-data = <&art 0x1000>;
+       mtd-mac-address = <&uboot 0x1fc00>;
+};

diff --git a/target/linux/ath79/image/tiny-tp-link.mk b/target/linux/ath79/image/tiny-tp-link.mk
index b358d3153e59bee7e2ca73d00e7d546f1bc0a81e..6ccc9d7dbaed0d5ae384ae297d2f99e87136edec 100644 (file)
--- a/target/linux/ath79/image/tiny-tp-link.mk
+++ b/target/linux/ath79/image/tiny-tp-link.mk
@@ -21,6 +21,16 @@ define Device/tplink_tl-mr3020-v1
 endef
 TARGET_DEVICES += tplink_tl-mr3020-v1
 
+define Device/tplink_tl-mr3040-v2
+  $(Device/tplink-4mlzma)
+  ATH_SOC := ar9331
+  DEVICE_TITLE := TP-LINK TL-MR3040 v2
+  DEVICE_PACKAGES := kmod-usb-core kmod-usb-chipidea2 kmod-usb-ledtrig-usbport
+  TPLINK_HWID := 0x30400002
+  SUPPORTED_DEVICES += tl-mr3040-v2
+endef
+TARGET_DEVICES += tplink_tl-mr3040-v2
+
 define Device/tplink_tl-mr3220-v1
   $(Device/tplink-4m)
   ATH_SOC := ar7241