Changes since U-Boot 1.1.1:
======================================================================
+* Patch by Jon Loeliger, 17 June 2004:
+ Completion of the 8540ADS/8560ADS updates:
+ Fix some PCI and Rapid I/O memory maps,
+ Initialize both TSEC 1 and 2,
+ Initialize SDRAM
+ Update MAINTAINER for 85xx boards and README.mpc85xxads
+
* Patch by Yuli Barcohen, 16 Jun 2004:
Remove obsolete AdderII port which was superseded by unified
AdderII/Adder87x port
Andrea "llandre" Marson <andrea.marson@dave-tech.it>
PPChameleonEVB PPC405EP
-
+
Reinhard Meyer <r.meyer@emk-elektronik.de>
TOP860 MPC860T
svm_sc8xx MPC8xx
-Xianghua Xiao <x.xiao@motorola.com>
+Jon Loeliger <jdl@freescale.com>
MPC8540ADS MPC8540
MPC8560ADS MPC8560
Andrea Scian <andrea.scian@dave-tech.it>
B2 ARM7TDMI (S3C44B0X)
-
+
Alex Züpke <azu@sysgo.de>
lart SA1100
## MPC85xx Systems
#########################################################################
-MPC8540ADS_config: unconfig
+MPC8540ADS_config: unconfig
@./mkconfig $(@:_config=) ppc mpc85xx mpc8540ads
-MPC8560ADS_config: unconfig
+MPC8560ADS_config: unconfig
@./mkconfig $(@:_config=) ppc mpc85xx mpc8560ads
-stxgp3_config: unconfig
+stxgp3_config: unconfig
@./mkconfig $(@:_config=) ppc mpc85xx stxgp3
#########################################################################
#include <command.h>
#include <malloc.h>
-
/* ------------------------------------------------------------------------- */
-
-
/* Prototypes */
int gunzip(void *, int, unsigned char *, int *);
-
int board_early_init_f (void)
{
out32(GPIO0_OR, CFG_NAND0_CE); /* set initial outputs */
#else
mtebc (epcr, 0x28400000); /* ebc in high-z */
#endif
-
return 0;
}
-
/* ------------------------------------------------------------------------- */
int misc_init_f (void)
udelay(1000); /* wait 1ms */
SET_FPGA(FPGA_PRG | FPGA_CLK | FPGA_DATA);
udelay(1000); /* wait 1ms */
-
#endif
#if 0
return (0);
}
-
/*
* Check Board Identity:
*/
tlb1_entry:
entry_start
- .long 0x0a /* the following data table uses a few of 16 TLB entries */
+ /* Number of entries in the following table */
+ .long 0x0c
.long TLB1_MAS0(1,1,0)
.long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_1M)
.long TLB1_MAS0(1,8,0)
.long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_256M)
- .long TLB1_MAS2(((CFG_PCI_MEM_BASE>>12) & 0xfffff),0,0,0,0,1,0,1,0)
- .long TLB1_MAS3(((CFG_PCI_MEM_BASE>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1)
+ .long TLB1_MAS2(((CFG_PCI1_MEM_BASE>>12) & 0xfffff),0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(((CFG_PCI1_MEM_BASE>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1)
.long TLB1_MAS0(1,9,0)
.long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_16K)
.long TLB1_MAS2(((CFG_BCSR>>12) & 0xfffff),0,0,0,0,1,0,1,0)
.long TLB1_MAS3(((CFG_BCSR>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1)
- #if (CFG_CCSRBAR_DEFAULT != CFG_CCSRBAR)
+ /*
+ * RapidIO MMU for 512M
+ * Two entries, 10 and 11
+ */
+ .long TLB1_MAS0(1,10,0)
+ .long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_256M)
+ .long TLB1_MAS2(((CFG_RIO_MEM_BASE>>12) & 0xfffff),0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(((CFG_RIO_MEM_BASE>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1)
+
+ .long TLB1_MAS0(1,11,0)
+ .long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_256M)
+ .long TLB1_MAS2(((CFG_RIO_MEM_BASE+0x10000000>>12) & 0xfffff),0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(((CFG_RIO_MEM_BASE+0x10000000>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1)
+
+
+#if (CFG_CCSRBAR_DEFAULT != CFG_CCSRBAR)
.long TLB1_MAS0(1,15,0)
.long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_1M)
.long TLB1_MAS2(((CFG_CCSRBAR_DEFAULT>>12) & 0xfffff),0,0,0,0,1,0,1,0)
.long TLB1_MAS3(((CFG_CCSRBAR_DEFAULT>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1)
- #else
+#else
.long TLB1_MAS0(1,15,0)
.long TLB1_MAS1(0,0,0,0,BOOKE_PAGESZ_1M)
.long TLB1_MAS2(0,0,0,0,0,0,0,0,0)
.long TLB1_MAS3(0,0,0,0,0,0,1,0,1,0,1)
- #endif
+#endif
entry_end
/*
* LAW(Local Access Window) configuration:
*
* 0x0000_0000 0x7fff_ffff DDR 2G
- * 0x8000_0000 0x9fff_ffff PCI MEM 512M
+ * 0x8000_0000 0x9fff_ffff PCI1 MEM 512M
+ * 0xc000_0000 0xdfff_ffff RapidIO 512M
* 0xe000_0000 0xe000_ffff CCSR 1M
- * 0xe200_0000 0xe2ff_ffff PCI IO 16M
+ * 0xe200_0000 0xe2ff_ffff PCI1 IO 16M
* 0xf000_0000 0xf7ff_ffff SDRAM 128M
* 0xf800_0000 0xf80f_ffff BCSR 1M
* 0xff00_0000 0xffff_ffff FLASH (boot bank) 16M
*
- * Note: CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
- * Note: If flash is 8M at default position(last 8M),no LAW needed.
+ * Notes:
+ * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
+ * If flash is 8M at default position (last 8M), no LAW needed.
*/
#if !defined(CONFIG_SPD_EEPROM)
#define LAWAR0 ((LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN)
#endif
-#define LAWBAR1 ((CFG_PCI_MEM_BASE>>12) & 0xfffff)
+#define LAWBAR1 ((CFG_PCI1_MEM_BASE>>12) & 0xfffff)
#define LAWAR1 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_512M))
/*
#define LAWAR2 ((LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN)
#endif
-#define LAWBAR3 ((CFG_PCI_IO_BASE>>12) & 0xfffff)
+#define LAWBAR3 ((CFG_PCI1_IO_BASE>>12) & 0xfffff)
#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_16M))
/*
* Rapid IO at 0xc000_0000 for 512 M
*/
-#define LAWBAR4 ((CFG_RAPID_IO_BASE>>12) & 0xfffff)
-#define LAWAR4 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_512M))
+#define LAWBAR4 ((CFG_RIO_MEM_BASE>>12) & 0xfffff)
+#define LAWAR4 (LAWAR_EN | LAWAR_TRGT_IF_RIO | (LAWAR_SIZE & LAWAR_SIZE_512M))
.section .bootpg, "ax"
/*
+ * Copyright 2004 Freescale Semiconductor.
* (C) Copyright 2002,2003, Motorola Inc.
* Xianghua Xiao, (X.Xiao@motorola.com)
*
*/
-extern long int spd_sdram (void);
-
#include <common.h>
#include <asm/processor.h>
#include <asm/immap_85xx.h>
#include <spd.h>
-long int fixed_sdram (void);
-
#if defined(CONFIG_DDR_ECC)
-void dma_init(void);
-uint dma_check(void);
-int dma_xfer(void *dest, uint count, void *src);
+extern void ddr_enable_ecc(unsigned int dram_size);
#endif
+extern long int spd_sdram(void);
+
+void sdram_init(void);
+long int fixed_sdram(void);
-/* MPC8540ADS Board Status & Control Registers */
-#if 0
-typedef struct bscr_ {
- unsigned long bcsr0;
- unsigned long bcsr1;
- unsigned long bcsr2;
- unsigned long bcsr3;
- unsigned long bcsr4;
- unsigned long bcsr5;
- unsigned long bcsr6;
- unsigned long bcsr7;
-} bcsr_t;
-#endif
int board_early_init_f (void)
{
#if defined(CONFIG_PCI)
- volatile immap_t *immr = (immap_t *)CFG_IMMR;
- volatile ccsr_pcix_t *pci = &immr->im_pcix;
+ volatile immap_t *immr = (immap_t *) CFG_IMMR;
+ volatile ccsr_pcix_t *pci = &immr->im_pcix;
- pci->peer &= 0xffffffdf; /* disable master abort */
+ pci->peer &= 0xffffffdf; /* disable master abort */
#endif
+
return 0;
}
int checkboard (void)
{
puts("Board: ADS\n");
+
+#ifdef CONFIG_PCI
+ printf(" PCI1: 32 bit, %d MHz (compiled)\n",
+ CONFIG_SYS_CLK_FREQ / 1000000);
+#else
+ printf(" PCI1: disabled\n");
+#endif
+
return 0;
}
-long int initdram (int board_type)
+long int
+initdram(int board_type)
{
long dram_size = 0;
extern long spd_sdram (void);
volatile immap_t *immap = (immap_t *)CFG_IMMR;
-#if !defined(CONFIG_RAM_AS_FLASH)
- volatile ccsr_lbc_t *lbc= &immap->im_lbc;
- sys_info_t sysinfo;
- uint temp_lbcdll = 0;
-#endif
-#if !defined(CONFIG_RAM_AS_FLASH) || defined(CONFIG_DDR_DLL)
- volatile ccsr_gur_t *gur= &immap->im_gur;
-#endif
-#if defined(CONFIG_DDR_DLL)
- uint temp_ddrdll = 0;
+ puts("Initializing\n");
- /* Work around to stabilize DDR DLL */
- temp_ddrdll = gur->ddrdllcr;
- gur->ddrdllcr = ((temp_ddrdll & 0xff) << 16) | 0x80000000;
- asm("sync;isync;msync");
+#if defined(CONFIG_DDR_DLL)
+ {
+ volatile ccsr_gur_t *gur= &immap->im_gur;
+ uint temp_ddrdll = 0;
+
+ /*
+ * Work around to stabilize DDR DLL
+ */
+ temp_ddrdll = gur->ddrdllcr;
+ gur->ddrdllcr = ((temp_ddrdll & 0xff) << 16) | 0x80000000;
+ asm("sync;isync;msync");
+ }
#endif
#if defined(CONFIG_SPD_EEPROM)
dram_size = fixed_sdram ();
#endif
-#if !defined(CONFIG_RAM_AS_FLASH) /* LocalBus is not emulating flash */
- get_sys_info(&sysinfo);
- /* if localbus freq is less than 66Mhz,we use bypass mode,otherwise use DLL */
- if(sysinfo.freqSystemBus/(CFG_LBC_LCRR & 0x0f) < 66000000) {
- lbc->lcrr = (CFG_LBC_LCRR & 0x0fffffff)| 0x80000000;
+#if defined(CONFIG_DDR_ECC)
+ /*
+ * Initialize and enable DDR ECC.
+ */
+ ddr_enable_ecc(dram_size);
+#endif
+
+ /*
+ * Initialize SDRAM.
+ */
+ sdram_init();
+
+ puts(" DDR: ");
+ return dram_size;
+}
+
+
+/*
+ * Initialize SDRAM memory on the Local Bus.
+ */
+
+void sdram_init (void)
+{
+#if !defined(CONFIG_RAM_AS_FLASH)
+ sys_info_t sysinfo;
+ volatile immap_t *immap = (immap_t *) CFG_IMMR;
+ volatile ccsr_lbc_t *lbc = &immap->im_lbc;
+ uint *sdram_addr = (uint *) CFG_LBC_SDRAM_BASE;
+
+ puts (" SDRAM: ");
+ print_size (CFG_LBC_SDRAM_SIZE * 1024 * 1024, "\n");
+
+ /*
+ * LocalBus SDRAM is not emulating flash.
+ */
+
+ /*
+ * Fix Local Bus clock glitch. Errata LBC11.
+ *
+ * If localbus freq is less than 66Mhz, use bypass mode,
+ * otherwise use DLL.
+ * lcrr is the local-bus clock ratio register.
+ */
+ get_sys_info (&sysinfo);
+ if (sysinfo.freqSystemBus / (CFG_LBC_LCRR & 0x0f) < 66000000) {
+ lbc->lcrr = (CFG_LBC_LCRR & 0x0fffffff) | 0x80000000;
+
} else {
- uint pvr = get_pvr();
+ /*
+ * On REV1 boards, need to change CLKDIV before enable DLL.
+ * Default CLKDIV is 8, change it to 4 temporarily.
+ */
+ volatile ccsr_gur_t *gur = &immap->im_gur;
+ uint pvr = get_pvr ();
+ uint temp_lbcdll = 0;
if (pvr == PVR_85xx_REV1) {
- /*
- * Need change CLKDIV before enable DLL.
- * Default CLKDIV is 8, change it to 4
- * temporarily.
- */
- lbc->lcrr = 0x10000004;
+ lbc->lcrr = 0x10000004;
}
+
+ /* FIXME: jdl Should lcrr have 0x8000000 OR'ed in here too? */
lbc->lcrr = CFG_LBC_LCRR & 0x7fffffff;
- udelay(200);
+ udelay (200);
temp_lbcdll = gur->lbcdllcr;
- gur->lbcdllcr = ((temp_lbcdll & 0xff) << 16 ) | 0x80000000;
- asm("sync;isync;msync");
+ gur->lbcdllcr = ((temp_lbcdll & 0xff) << 16) | 0x80000000;
+ asm ("sync;isync;msync");
}
- lbc->or2 = CFG_OR2_PRELIM; /* 64MB SDRAM */
+
+ /*
+ * Setup SDRAM Base and Option Registers
+ */
+ lbc->or2 = CFG_OR2_PRELIM;
lbc->br2 = CFG_BR2_PRELIM;
lbc->lbcr = CFG_LBC_LBCR;
+ asm ("msync");
+
+ lbc->lsrt = CFG_LBC_LSRT;
+ lbc->mrtpr = CFG_LBC_MRTPR;
+ asm ("sync");
+
+ /*
+ * Configure the SDRAM controller.
+ */
lbc->lsdmr = CFG_LBC_LSDMR_1;
- asm("sync");
- (unsigned int) * (ulong *)0 = 0x000000ff;
+ asm ("sync");
+ *sdram_addr = 0xff;
+ ppcDcbf ((unsigned long) sdram_addr);
+ udelay (100);
+
lbc->lsdmr = CFG_LBC_LSDMR_2;
- asm("sync");
- (unsigned int) * (ulong *)0 = 0x000000ff;
+ asm ("sync");
+ *sdram_addr = 0xff;
+ ppcDcbf ((unsigned long) sdram_addr);
+ udelay (100);
+
lbc->lsdmr = CFG_LBC_LSDMR_3;
- asm("sync");
- (unsigned int) * (ulong *)0 = 0x000000ff;
- lbc->lsdmr = CFG_LBC_LSDMR_4;
- asm("sync");
- (unsigned int) * (ulong *)0 = 0x000000ff;
- lbc->lsdmr = CFG_LBC_LSDMR_5;
- asm("sync");
- lbc->lsrt = CFG_LBC_LSRT;
- asm("sync");
- lbc->mrtpr = CFG_LBC_MRTPR;
- asm("sync");
-#endif
+ asm ("sync");
+ *sdram_addr = 0xff;
+ ppcDcbf ((unsigned long) sdram_addr);
+ udelay (100);
-#if defined(CONFIG_DDR_ECC)
- {
- /* Initialize all of memory for ECC, then
- * enable errors */
- uint *p = 0;
- uint i = 0;
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
- volatile ccsr_ddr_t *ddr= &immap->im_ddr;
- dma_init();
- for (*p = 0; p < (uint *)(8 * 1024); p++) {
- if (((unsigned int)p & 0x1f) == 0) { dcbz(p); }
- *p = (unsigned int)0xdeadbeef;
- if (((unsigned int)p & 0x1c) == 0x1c) { dcbf(p); }
- }
+ lbc->lsdmr = CFG_LBC_LSDMR_4;
+ asm ("sync");
+ *sdram_addr = 0xff;
+ ppcDcbf ((unsigned long) sdram_addr);
+ udelay (100);
- /* 8K */
- dma_xfer((uint *)0x2000,0x2000,(uint *)0);
- /* 16K */
- dma_xfer((uint *)0x4000,0x4000,(uint *)0);
- /* 32K */
- dma_xfer((uint *)0x8000,0x8000,(uint *)0);
- /* 64K */
- dma_xfer((uint *)0x10000,0x10000,(uint *)0);
- /* 128k */
- dma_xfer((uint *)0x20000,0x20000,(uint *)0);
- /* 256k */
- dma_xfer((uint *)0x40000,0x40000,(uint *)0);
- /* 512k */
- dma_xfer((uint *)0x80000,0x80000,(uint *)0);
- /* 1M */
- dma_xfer((uint *)0x100000,0x100000,(uint *)0);
- /* 2M */
- dma_xfer((uint *)0x200000,0x200000,(uint *)0);
- /* 4M */
- dma_xfer((uint *)0x400000,0x400000,(uint *)0);
-
- for (i = 1; i < dram_size / 0x800000; i++) {
- dma_xfer((uint *)(0x800000*i),0x800000,(uint *)0);
- }
+ lbc->lsdmr = CFG_LBC_LSDMR_5;
+ asm ("sync");
+ *sdram_addr = 0xff;
+ ppcDcbf ((unsigned long) sdram_addr);
+ udelay (100);
- /* Enable errors for ECC */
- ddr->err_disable = 0x00000000;
- asm("sync;isync;msync");
- }
#endif
-
- return dram_size;
}
asm("sync; isync; msync");
udelay(500);
#endif
- return (CFG_SDRAM_SIZE * 1024 * 1024);
+ return CFG_SDRAM_SIZE * 1024 * 1024;
}
#endif /* !defined(CONFIG_SPD_EEPROM) */
tlb1_entry:
entry_start
- .long 0x0a /* the following data table uses a few of 16 TLB entries */
+ /* Number of entries in the following table */
+ .long 0x0c
.long TLB1_MAS0(1,1,0)
.long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_1M)
.long TLB1_MAS0(1,8,0)
.long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_256M)
- .long TLB1_MAS2(((CFG_PCI_MEM_BASE>>12) & 0xfffff),0,0,0,0,1,0,1,0)
- .long TLB1_MAS3(((CFG_PCI_MEM_BASE>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1)
+ .long TLB1_MAS2(((CFG_PCI1_MEM_BASE>>12) & 0xfffff),0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(((CFG_PCI1_MEM_BASE>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1)
.long TLB1_MAS0(1,9,0)
.long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_16K)
.long TLB1_MAS2(((CFG_BCSR>>12) & 0xfffff),0,0,0,0,1,0,1,0)
.long TLB1_MAS3(((CFG_BCSR>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1)
- #if (CFG_CCSRBAR_DEFAULT != CFG_CCSRBAR)
+ /*
+ * RapidIO MMU for 512M
+ * Two entries, 10 and 11
+ */
+ .long TLB1_MAS0(1,10,0)
+ .long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_256M)
+ .long TLB1_MAS2(((CFG_RIO_MEM_BASE>>12) & 0xfffff),0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(((CFG_RIO_MEM_BASE>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1)
+
+ .long TLB1_MAS0(1,11,0)
+ .long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_256M)
+ .long TLB1_MAS2(((CFG_RIO_MEM_BASE+0x10000000>>12) & 0xfffff),0,0,0,0,1,0,1,0)
+ .long TLB1_MAS3(((CFG_RIO_MEM_BASE+0x10000000>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1)
+
+
+#if (CFG_CCSRBAR_DEFAULT != CFG_CCSRBAR)
.long TLB1_MAS0(1,15,0)
.long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_1M)
.long TLB1_MAS2(((CFG_CCSRBAR_DEFAULT>>12) & 0xfffff),0,0,0,0,1,0,1,0)
.long TLB1_MAS3(((CFG_CCSRBAR_DEFAULT>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1)
- #else
+#else
.long TLB1_MAS0(1,15,0)
.long TLB1_MAS1(0,0,0,0,BOOKE_PAGESZ_1M)
.long TLB1_MAS2(0,0,0,0,0,0,0,0,0)
.long TLB1_MAS3(0,0,0,0,0,0,1,0,1,0,1)
- #endif
+#endif
entry_end
/*
* LAW(Local Access Window) configuration:
*
* 0x0000_0000 0x7fff_ffff DDR 2G
- * 0x8000_0000 0x9fff_ffff PCI MEM 512M
+ * 0x8000_0000 0x9fff_ffff PCI1 MEM 512M
+ * 0xc000_0000 0xdfff_ffff RapidIO 512M
* 0xe000_0000 0xe000_ffff CCSR 1M
- * 0xe200_0000 0xe2ff_ffff PCI IO 16M
+ * 0xe200_0000 0xe2ff_ffff PCI1 IO 16M
* 0xf000_0000 0xf7ff_ffff SDRAM 128M
* 0xf800_0000 0xf80f_ffff BCSR 1M
* 0xff00_0000 0xffff_ffff FLASH (boot bank) 16M
*
- * Note: CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
- * Note: If flash is 8M at default position(last 8M),no LAW needed.
+ * Notes:
+ * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
+ * If flash is 8M at default position (last 8M), no LAW needed.
*/
#if !defined(CONFIG_SPD_EEPROM)
#define LAWAR0 ((LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN)
#endif
-#define LAWBAR1 ((CFG_PCI_MEM_BASE>>12) & 0xfffff)
+#define LAWBAR1 ((CFG_PCI1_MEM_BASE>>12) & 0xfffff)
#define LAWAR1 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_512M))
/*
#define LAWAR2 ((LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN)
#endif
-#define LAWBAR3 ((CFG_PCI_IO_BASE>>12) & 0xfffff)
+#define LAWBAR3 ((CFG_PCI1_IO_BASE>>12) & 0xfffff)
#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_16M))
/*
* Rapid IO at 0xc000_0000 for 512 M
*/
-#define LAWBAR4 ((CFG_RAPID_IO_BASE>>12) & 0xfffff)
-#define LAWAR4 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_512M))
+#define LAWBAR4 ((CFG_RIO_MEM_BASE>>12) & 0xfffff)
+#define LAWAR4 (LAWAR_EN | LAWAR_TRGT_IF_RIO | (LAWAR_SIZE & LAWAR_SIZE_512M))
.section .bootpg, "ax"
*/
-extern long int spd_sdram (void);
-
#include <common.h>
#include <asm/processor.h>
#include <asm/immap_85xx.h>
#include <spd.h>
#include <miiphy.h>
-long int fixed_sdram (void);
+#if defined(CONFIG_DDR_ECC)
+extern void ddr_enable_ecc(unsigned int dram_size);
+#endif
+
+extern long int spd_sdram(void);
+
+void sdram_init(void);
+long int fixed_sdram(void);
+
/*
* I/O Port configuration table
}
};
-/* MPC8560ADS Board Status & Control Registers */
-typedef struct bscr_ {
+
+/*
+ * MPC8560ADS Board Status & Control Registers
+ */
+typedef struct bcsr_ {
volatile unsigned char bcsr0;
volatile unsigned char bcsr1;
volatile unsigned char bcsr2;
int board_early_init_f (void)
{
#if defined(CONFIG_PCI)
- volatile immap_t *immr = (immap_t *)CFG_IMMR;
- volatile ccsr_pcix_t *pci = &immr->im_pcix;
+ volatile immap_t *immr = (immap_t *) CFG_IMMR;
+ volatile ccsr_pcix_t *pci = &immr->im_pcix;
- pci->peer &= 0xfffffffdf; /* disable master abort */
+ pci->peer &= 0xffffffdf; /* disable master abort */
#endif
+
return 0;
}
#endif /* CONFIG_MII */
}
-
int checkboard (void)
{
puts("Board: ADS\n");
+
+#ifdef CONFIG_PCI
+ printf(" PCI1: 32 bit, %d MHz (compiled)\n",
+ CONFIG_SYS_CLK_FREQ / 1000000);
+#else
+ printf(" PCI1: disabled\n");
+#endif
return 0;
}
-long int initdram (int board_type)
+long int
+initdram(int board_type)
{
long dram_size = 0;
extern long spd_sdram (void);
volatile immap_t *immap = (immap_t *)CFG_IMMR;
-#if !defined(CONFIG_RAM_AS_FLASH)
- volatile ccsr_lbc_t *lbc= &immap->im_lbc;
- sys_info_t sysinfo;
- uint temp_lbcdll = 0;
-#endif
-#if !defined(CONFIG_RAM_AS_FLASH) || defined(CONFIG_DDR_DLL)
- volatile ccsr_gur_t *gur= &immap->im_gur;
-#endif
-#if defined(CONFIG_DDR_DLL)
- uint temp_ddrdll = 0;
+ puts("Initializing\n");
- /* Work around to stabilize DDR DLL */
- temp_ddrdll = gur->ddrdllcr;
- gur->ddrdllcr = ((temp_ddrdll & 0xff) << 16) | 0x80000000;
- asm("sync;isync;msync");
+#if defined(CONFIG_DDR_DLL)
+ {
+ volatile ccsr_gur_t *gur= &immap->im_gur;
+ uint temp_ddrdll = 0;
+
+ /*
+ * Work around to stabilize DDR DLL
+ */
+ temp_ddrdll = gur->ddrdllcr;
+ gur->ddrdllcr = ((temp_ddrdll & 0xff) << 16) | 0x80000000;
+ asm("sync;isync;msync");
+ }
#endif
#if defined(CONFIG_SPD_EEPROM)
dram_size = fixed_sdram ();
#endif
-#if !defined(CONFIG_RAM_AS_FLASH) /* LocalBus SDRAM is not emulating flash */
- get_sys_info(&sysinfo);
- /* if localbus freq is less than 66Mhz,we use bypass mode,otherwise use DLL */
- if(sysinfo.freqSystemBus/(CFG_LBC_LCRR & 0x0f) < 66000000) {
- lbc->lcrr = (CFG_LBC_LCRR & 0x0fffffff)| 0x80000000;
+#if defined(CONFIG_DDR_ECC)
+ /*
+ * Initialize and enable DDR ECC.
+ */
+ ddr_enable_ecc(dram_size);
+#endif
+
+ /*
+ * Initialize SDRAM.
+ */
+ sdram_init();
+
+ puts(" DDR: ");
+ return dram_size;
+}
+
+
+/*
+ * Initialize SDRAM memory on the Local Bus.
+ */
+
+void sdram_init (void)
+{
+#if !defined(CONFIG_RAM_AS_FLASH)
+ sys_info_t sysinfo;
+ volatile immap_t *immap = (immap_t *) CFG_IMMR;
+ volatile ccsr_lbc_t *lbc = &immap->im_lbc;
+ uint *sdram_addr = (uint *) CFG_LBC_SDRAM_BASE;
+
+ puts (" SDRAM: ");
+ print_size (CFG_LBC_SDRAM_SIZE * 1024 * 1024, "\n");
+
+ /*
+ * LocalBus SDRAM is not emulating flash.
+ */
+
+ /*
+ * Fix Local Bus clock glitch. Errata LBC11.
+ *
+ * If localbus freq is less than 66Mhz, use bypass mode,
+ * otherwise use DLL.
+ * lcrr is the local-bus clock ratio register.
+ */
+ get_sys_info (&sysinfo);
+ if (sysinfo.freqSystemBus / (CFG_LBC_LCRR & 0x0f) < 66000000) {
+ lbc->lcrr = (CFG_LBC_LCRR & 0x0fffffff) | 0x80000000;
+
} else {
- uint pvr = get_pvr();
+ /*
+ * On REV1 boards, need to change CLKDIV before enable DLL.
+ * Default CLKDIV is 8, change it to 4 temporarily.
+ */
+ volatile ccsr_gur_t *gur = &immap->im_gur;
+ uint pvr = get_pvr ();
+ uint temp_lbcdll = 0;
if (pvr == PVR_85xx_REV1) {
- /*
- * Need change CLKDIV before enable DLL.
- * Default CLKDIV is 8, change it to 4
- * temporarily.
- */
- lbc->lcrr = 0x10000004;
+ lbc->lcrr = 0x10000004;
}
+
+ /* FIXME: jdl Should lcrr have 0x8000000 OR'ed in here too? */
lbc->lcrr = CFG_LBC_LCRR & 0x7fffffff;
- udelay(200);
+ udelay (200);
temp_lbcdll = gur->lbcdllcr;
- gur->lbcdllcr = ((temp_lbcdll & 0xff) << 16 ) | 0x80000000;
- asm("sync;isync;msync");
+ gur->lbcdllcr = ((temp_lbcdll & 0xff) << 16) | 0x80000000;
+ asm ("sync;isync;msync");
}
- lbc->or2 = CFG_OR2_PRELIM; /* 64MB SDRAM */
+
+ /*
+ * Setup SDRAM Base and Option Registers
+ */
+ lbc->or2 = CFG_OR2_PRELIM;
lbc->br2 = CFG_BR2_PRELIM;
lbc->lbcr = CFG_LBC_LBCR;
+ asm ("msync");
+
+ lbc->lsrt = CFG_LBC_LSRT;
+ lbc->mrtpr = CFG_LBC_MRTPR;
+ asm ("sync");
+
+ /*
+ * Configure the SDRAM controller.
+ */
lbc->lsdmr = CFG_LBC_LSDMR_1;
- asm("sync");
- (unsigned int) * (ulong *)0 = 0x000000ff;
+ asm ("sync");
+ *sdram_addr = 0xff;
+ ppcDcbf ((unsigned long) sdram_addr);
+ udelay (100);
+
lbc->lsdmr = CFG_LBC_LSDMR_2;
- asm("sync");
- (unsigned int) * (ulong *)0 = 0x000000ff;
+ asm ("sync");
+ *sdram_addr = 0xff;
+ ppcDcbf ((unsigned long) sdram_addr);
+ udelay (100);
+
lbc->lsdmr = CFG_LBC_LSDMR_3;
- asm("sync");
- (unsigned int) * (ulong *)0 = 0x000000ff;
- lbc->lsdmr = CFG_LBC_LSDMR_4;
- asm("sync");
- (unsigned int) * (ulong *)0 = 0x000000ff;
- lbc->lsdmr = CFG_LBC_LSDMR_5;
- asm("sync");
- lbc->lsrt = CFG_LBC_LSRT;
- asm("sync");
- lbc->mrtpr = CFG_LBC_MRTPR;
- asm("sync");
-#endif
+ asm ("sync");
+ *sdram_addr = 0xff;
+ ppcDcbf ((unsigned long) sdram_addr);
+ udelay (100);
-#if defined(CONFIG_DDR_ECC)
- {
- /* Initialize all of memory for ECC, then
- * enable errors */
- uint *p = 0;
- uint i = 0;
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
- volatile ccsr_ddr_t *ddr= &immap->im_ddr;
- dma_init();
- for (*p = 0; p < (uint *)(8 * 1024); p++) {
- if (((unsigned int)p & 0x1f) == 0) { dcbz(p); }
- *p = (unsigned int)0xdeadbeef;
- if (((unsigned int)p & 0x1c) == 0x1c) { dcbf(p); }
- }
+ lbc->lsdmr = CFG_LBC_LSDMR_4;
+ asm ("sync");
+ *sdram_addr = 0xff;
+ ppcDcbf ((unsigned long) sdram_addr);
+ udelay (100);
- /* 8K */
- dma_xfer((uint *)0x2000,0x2000,(uint *)0);
- /* 16K */
- dma_xfer((uint *)0x4000,0x4000,(uint *)0);
- /* 32K */
- dma_xfer((uint *)0x8000,0x8000,(uint *)0);
- /* 64K */
- dma_xfer((uint *)0x10000,0x10000,(uint *)0);
- /* 128k */
- dma_xfer((uint *)0x20000,0x20000,(uint *)0);
- /* 256k */
- dma_xfer((uint *)0x40000,0x40000,(uint *)0);
- /* 512k */
- dma_xfer((uint *)0x80000,0x80000,(uint *)0);
- /* 1M */
- dma_xfer((uint *)0x100000,0x100000,(uint *)0);
- /* 2M */
- dma_xfer((uint *)0x200000,0x200000,(uint *)0);
- /* 4M */
- dma_xfer((uint *)0x400000,0x400000,(uint *)0);
-
- for (i = 1; i < dram_size / 0x800000; i++) {
- dma_xfer((uint *)(0x800000*i),0x800000,(uint *)0);
- }
+ lbc->lsdmr = CFG_LBC_LSDMR_5;
+ asm ("sync");
+ *sdram_addr = 0xff;
+ ppcDcbf ((unsigned long) sdram_addr);
+ udelay (100);
- /* Enable errors for ECC */
- ddr->err_disable = 0x00000000;
- asm("sync;isync;msync");
- }
#endif
-
- return dram_size;
}
}
#endif
+
#if !defined(CONFIG_SPD_EEPROM)
/*************************************************************************
* fixed sdram init -- doesn't use serial presence detect.
asm("sync; isync; msync");
udelay(500);
#endif
- return ( CFG_SDRAM_SIZE * 1024 * 1024);
+ return CFG_SDRAM_SIZE * 1024 * 1024;
}
#endif /* !defined(CONFIG_SPD_EEPROM) */
#endif /* CONFIG_WATCHDOG */
#if defined(CONFIG_DDR_ECC)
-__inline__ void dcbz(const void* addr)
-{
- __asm__ __volatile__ ("dcbz 0,%0" :: "r" (addr));
-}
-
-__inline__ void dcbf(const void* addr)
-{
- __asm__ __volatile__ ("dcbf 0,%0" :: "r" (addr));
-}
-
void dma_init(void) {
volatile immap_t *immap = (immap_t *)CFG_IMMR;
volatile ccsr_dma_t *dma = &immap->im_dma;
/*
+ * Copyright 2004 Freescale Semiconductor.
* Copyright (C) 2003 Motorola Inc.
* Xianghua Xiao (x.xiao@motorola.com)
*
#include <asm/cpm_85xx.h>
#include <pci.h>
+
#if defined(CONFIG_PCI)
+
+
/*
* Initialize PCI Devices, report devices found.
*/
+
#ifndef CONFIG_PCI_PNP
static struct pci_config_table pci_mpc85xxads_config_table[] = {
- { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_IDSEL_NUMBER, PCI_ANY_ID,
- pci_cfgfunc_config_device, { PCI_ENET0_IOADDR,
- PCI_ENET0_MEMADDR,
- PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER }},
- { }
+ {PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
+ PCI_IDSEL_NUMBER, PCI_ANY_ID,
+ pci_cfgfunc_config_device, {PCI_ENET0_IOADDR,
+ PCI_ENET0_MEMADDR,
+ PCI_COMMAND_MEMORY |
+ PCI_COMMAND_MASTER}},
+ {}
};
#endif
#endif
};
-void pci_init_board(void)
-{
- struct pci_controller* hose = (struct pci_controller *)&local_hose;
- volatile immap_t *immap = (immap_t *)CFG_CCSRBAR;
- volatile ccsr_pcix_t *pcix = &immap->im_pcix;
-
- u16 reg16;
-
- hose->first_busno = 0;
- hose->last_busno = 0xff;
-
- pci_set_region(hose->regions + 0,
- CFG_PCI_MEM_BASE,
- CFG_PCI_MEM_PHYS,
- (CFG_PCI_MEM_SIZE/2),
- PCI_REGION_MEM);
-
- pci_set_region(hose->regions + 1,
- (CFG_PCI_MEM_BASE+0x08000000),
- (CFG_PCI_MEM_PHYS+0x08000000),
- 0x1000000, /* 16M */
- PCI_REGION_IO);
-
- hose->region_count = 2;
-
- pci_setup_indirect(hose,
- (CFG_IMMR+0x8000),
- (CFG_IMMR+0x8004));
-
- pci_register_hose(hose);
-
- hose->last_busno = pci_hose_scan(hose);
-
- pci_read_config_word (PCI_BDF(0,0,0), PCI_COMMAND, ®16);
- reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
- pci_write_config_word(PCI_BDF(0,0,0), PCI_COMMAND, reg16);
-
- /* Clear non-reserved bits in status register */
- pci_write_config_word(PCI_BDF(0,0,0), PCI_STATUS, 0xffff);
- pci_write_config_byte(PCI_BDF(0,0,0), PCI_LATENCY_TIMER,0x80);
-
- pcix->potar1 = (CFG_PCI_MEM_BASE >> 12) & 0x000fffff;
- pcix->potear1 = 0x00000000;
- pcix->powbar1 = (CFG_PCI_MEM_BASE >> 12) & 0x000fffff;
- pcix->powbear1 = 0x00000000;
- pcix->powar1 = 0x8004401a; /* 128M MEM space */
- pcix->potar2 = ((CFG_PCI_MEM_BASE + 0x08000000) >> 12) & 0x000fffff;
- pcix->potear2 = 0x00000000;
- pcix->powbar2 = ((CFG_PCI_MEM_BASE + 0x08000000) >> 12) && 0x000fffff;
- pcix->powbear2 = 0x00000000;
- pcix->powar2 = 0x80088017; /* 16M IO space */
- pcix->pitar1 = 0x00000000;
- pcix->piwbar1 = 0x00000000;
- pcix->piwar1 = 0xa0F5501f;
+void pci_init_board (void)
+{
+ struct pci_controller *hose = (struct pci_controller *) &local_hose;
+ volatile immap_t *immap = (immap_t *) CFG_CCSRBAR;
+ volatile ccsr_pcix_t *pcix = &immap->im_pcix;
+
+ u16 reg16;
+
+ hose->first_busno = 0;
+ hose->last_busno = 0xff;
+
+ pci_set_region (hose->regions + 0,
+ CFG_PCI1_MEM_BASE,
+ CFG_PCI1_MEM_PHYS, CFG_PCI1_MEM_SIZE, PCI_REGION_MEM);
+
+ pci_set_region (hose->regions + 1,
+ CFG_PCI1_IO_BASE,
+ CFG_PCI1_IO_PHYS, CFG_PCI1_IO_SIZE, PCI_REGION_IO);
+
+ hose->region_count = 2;
+
+ pci_setup_indirect (hose, (CFG_IMMR + 0x8000), (CFG_IMMR + 0x8004));
+
+ pci_read_config_word (PCI_BDF (0, 0, 0), PCI_COMMAND, ®16);
+ reg16 |= PCI_COMMAND_SERR | PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+ pci_write_config_word (PCI_BDF (0, 0, 0), PCI_COMMAND, reg16);
+
+ /*
+ * Clear non-reserved bits in status register.
+ */
+ pci_write_config_word (PCI_BDF (0, 0, 0), PCI_STATUS, 0xffff);
+ pci_write_config_byte (PCI_BDF (0, 0, 0), PCI_LATENCY_TIMER, 0x80);
+
+ pcix->potar1 = (CFG_PCI1_MEM_BASE >> 12) & 0x000fffff;
+ pcix->potear1 = 0x00000000;
+ pcix->powbar1 = (CFG_PCI1_MEM_BASE >> 12) & 0x000fffff;
+ pcix->powbear1 = 0x00000000;
+ pcix->powar1 = 0x8004401c; /* 512M MEM space */
+
+ pcix->potar2 = (CFG_PCI1_IO_BASE >> 12) & 0x000fffff;
+ pcix->potear2 = 0x00000000;
+ pcix->powbar2 = (CFG_PCI1_IO_BASE >> 12) & 0x000fffff;
+ pcix->powbear2 = 0x00000000;
+ pcix->powar2 = 0x80088017; /* 16M IO space */
+
+ pcix->pitar1 = 0x00000000;
+ pcix->piwbar1 = 0x00000000;
+ pcix->piwar1 = 0xa0F5501f;
+
+ /*
+ * Hose scan.
+ */
+ pci_register_hose (hose);
+ hose->last_busno = pci_hose_scan (hose);
}
+
#endif /* CONFIG_PCI */
/* disable d-cache */
li r0,0x0
mtspr L1CSR0,r0
- isync
/* invalidate i-cache */
mfspr r0,L1CSR1
isync
/* clear registers */
- sync
li r0,0
mtspr SRR0,r0
mtspr SRR1,r0
mtspr DEAR,r0
mtspr DBCR0,r0
- isync
mtspr DBCR1,r0
- isync
mtspr DBCR2,r0
- isync
mtspr IAC1,r0
mtspr IAC2,r0
mtspr DAC1,r0
mfspr r1,DBSR
mtspr DBSR,r1 /* Clear all valid bits */
- isync
mtspr PID0,r0
- isync
mtspr PID1,r0
- isync
mtspr PID2,r0
- isync
-
mtspr TCR,r0
mtspr BUCSR,r0 /* disable branch prediction */
- isync
-
- mtspr HID0,r0
- isync
- mtspr HID1,r0
- isync
-
mtspr MAS4,r0
- isync
mtspr MAS6,r0
isync
isync
/* Enable Time Base and Select Time Base Clock */
- li r0,0x4000 /* time base is processor clock */
+ lis r0,HID0_EMCP@h /* Enable machine check */
+ ori r0,r0,0x4000 /* time base is processor clock */
mtspr HID0,r0
- isync
#if defined(CONFIG_ADDR_STREAMING)
li r0,0x3000
li r0,0x1000
#endif
mtspr HID1,r0
- isync
/* Enable Branch Prediction */
#if defined(CONFIG_BTB)
li r0,0x201 /* BBFI = 1, BPEN = 1 */
mtspr BUCSR,r0
- isync
#endif
#if defined(CFG_INIT_DBCR)
lis r1,0xffff
ori r1,r1,0xffff
- mtspr dbsr,r1 /* Clear all status bits */
+ mtspr DBSR,r1 /* Clear all status bits */
lis r0,CFG_INIT_DBCR@h /* DBCR0[IDM] must be set */
ori r0,r0,CFG_INIT_DBCR@l
- mtspr dbcr0,r0
- isync
+ mtspr DBCR0,r0
#endif
/* L1 DCache is used for initial RAM */
mfspr r2, L1CSR0
ori r2, r2, 0x0003
oris r2, r2, 0x0001
- msync
- isync
mtspr L1CSR0, r2 /* enable/invalidate L1 Dcache */
isync
bl cpu_init_f
bl icache_enable
bl board_init_f
- sync
-
+ isync
/* --FIXME-- machine check with MCSRRn and rfmci */
dcbi r0,r3
blr
+/*--------------------------------------------------------------------------
+ * Function: ppcDcbz
+ * Description: Data Cache block zero.
+ * Input: r3 = effective address
+ * Output: none.
+ *-------------------------------------------------------------------------- */
+
+ .globl ppcDcbz
+ppcDcbz:
+ dcbz r0,r3
+ blr
+
/*------------------------------------------------------------------------------- */
/* Function: ppcSync */
/* Description: Processor Synchronize */
shipped with your board. Then apply the following changes:
SW3[1-6]="all OFF" (boot from 32bit flash, no boot sequence is used)
SW10[2-6]="all OFF" (turn on CPM SCC for serial port,works for 8540/8560)
- SW11[2]='OFF for 8560, ON for 8540' (single switch to toggle 8540.8560 mode)
+ SW11[2]='OFF for 8560, ON for 8540' (toggle 8540.8560 mode)
SW11[7]='ON' (rev2), 'OFF' (rev1)
SW4[7-8]="OFF OFF" (enable serial ports,I'm using the top serial connector)
SW22[1-4]="OFF OFF ON OFF"
have to change the system clock from the default 66Mhz to 33Mhz by
setting SW15[1]="OFF" and SW17[8]="OFF". After that you may also need
double your platform clock(SW6) because the system clock is now only
- half of its original value.
+ half of its original value. For example, if at 66MHz your system
+ clock showed SW6[0:1] = 01, then at 33MHz SW6[0:1] it should be 10.
1.3 SW6 is a very important switch, it decides your platform clock and CPU
clock based on the on-board system clock(default 66MHz). Check the
0x0000_0000 0x7fff_ffff DDR 2G
0x8000_0000 0x9fff_ffff PCI MEM 512M
0xc000_0000 0xdfff_ffff Rapid IO 512M
- 0xe000_0000 0xe000_ffff CCSR 1M
+ 0xe000_0000 0xe00f_ffff CCSR 1M
0xe200_0000 0xe2ff_ffff PCI IO 16M
0xf000_0000 0xf7ff_ffff SDRAM 128M
0xf800_0000 0xf80f_ffff BCSR 1M
arch/ppc/configs/mpc8540_ads_defconfig
arch/ppc/configs/mpc8560_ads_defconfig
-
3. DEFINITIONS AND COMPILATION
-3.1 Explanation on NEW definitions in include/configs/MPC8540ADS.h and include/
- configs/MPC8560ADS.h
+3.1 Explanation on NEW definitions in:
+ include/configs/MPC8540ADS.h
+ include/configs/MPC8560ADS.h
+
CONFIG_BOOKE BOOKE(e.g. Motorola MPC85xx, IBM 440, etc)
CONFIG_E500 BOOKE e500 family(Motorola)
CONFIG_MPC85xx MPC8540,MPC8560 and their derivatives
CONFIG_MPC8540ADS MPC8540ADS board specific
CONFIG_MPC8560ADS MPC8560ADS board specific
CONFIG_TSEC_ENET Use on-chip 10/100/1000 ethernet for networking
- CONFIG_SPD_EEPROM Use SPD EEPROM for DDR auto configuration, you can also
- manual config the DDR after undef this definition.
+ CONFIG_SPD_EEPROM Use SPD EEPROM for DDR auto configuration, you can
+ also manual config the DDR after undef this
+ definition.
CONFIG_DDR_ECC only for ECC DDR module
- CONFIG_DDR_DLL DLL fix on some ADS boards needed for more stability.
- CONFIG_RAM_AS_FLASH after define this, you can load U-Boot into localbus
- SDRAM and treat localbus SDRAM as a flash. We use this
- memory based U-Boot before flash is working while Metrowerks
- and Windriver are still working on their flash/JTAG tools.
- if you can program the flash directly, undef this.
- Other than the above definitions, the rest in the config files are straightforward.
+ CONFIG_DDR_DLL DLL fix on some ADS boards needed for more
+ stability.
+ CONFIG_RAM_AS_FLASH after define this, you can load U-Boot into
+ localbus SDRAM and treat localbus SDRAM as a
+ flash. We use this memory based U-Boot
+ before flash is working while Metrowerks and
+ Windriver are still working on their
+ flash/JTAG tools. if you can program the
+ flash directly, undef this.
+
+Other than the above definitions, the rest in the config files are
+straightforward.
+
3.2 Compilation
- export CROSS_COMPILE=your-cross-compile-prefix(assuming you're using BASH shell)
- cd u-boot
- make distclean
- make MPC8560ADS_config (or make MPC8540ADS_config)
- make
+ Assuming you're using BASH shell:
+
+ export CROSS_COMPILE=your-cross-compile-prefix
+ cd u-boot
+ make distclean
+ make MPC8560ADS_config (or make MPC8540ADS_config)
+ make
4. Notes:
4.1 When connecting with kermit, the following commands must be present.in
- your .kermrc file. These are especially important when booting as
- MPC8560, as the serial console will not work without them:
-
-set speed 115200
-set carrier-watch off
-set handshake none
-set flow-control none
-robust
-
-4.2 Sometimes after U-Boot is up, the 'tftp' won't work well with TSEC ethernet. If that
- happens, you can try the following steps to make network work:
- MPC8560ADS>tftp 1000000 pImage
- (if it hangs, use Ctrl-C to quit)
- MPC8560ADS>nm fdf24524
- >0
- >1
- >. (to quit this memory operation)
- MPC8560ADS>tftp 1000000 pImage
-
-4.3 If you're one of the early developers using the Rev1 8540/8560 chips, please use U-Boot
- 1.0.0, as the newer silicon will only support Rev2 and future revisions of 8540/8560.
+ your .kermrc file. These are especially important when booting as
+ MPC8560, as the serial console will not work without them:
+
+ set speed 115200
+ set carrier-watch off
+ set handshake none
+ set flow-control none
+ robust
+
+
+4.2 Sometimes after U-Boot is up, the 'tftp' won't work well with TSEC
+ ethernet. If that happens, you can try the following steps to make
+ network work:
+
+ MPC8560ADS>tftp 1000000 pImage
+ (if it hangs, use Ctrl-C to quit)
+ MPC8560ADS>nm fdf24524
+ >0
+ >1
+ >. (to quit this memory operation)
+ MPC8560ADS>tftp 1000000 pImage
+
+4.3 If you're one of the early developers using the Rev1 8540/8560 chips,
+ please use U-Boot 1.0.0, as the newer silicon will only support Rev2
+ and future revisions of 8540/8560.
+
4.4 Reflash U-boot Image using U-boot
=> cp.b 0 fff80000 80000
-5. Screen dump:
+4.5 Reflash U-Boot with a BDI-2000
+ BDI> erase 0xFFF80000 0x2000 0x40
+ BDI> prog 0xfff80000 u-boot.bin.8560ads
+ BDI> verify
+
+
+5. Screen dump:
5.1 MPC8540ADS board
U-Boot 1.0.0-pre (Oct 15 2003 - 13:40:33)
#define LAWAR_SIZE 0x0000003F
#define LAWAR_TRGT_IF_PCI 0x00000000
+#define LAWAR_TRGT_IF_PCI1 0x00000000
#define LAWAR_TRGT_IF_PCIX 0x00000000
+#define LAWAR_TRGT_IF_PCI2 0x00100000
#define LAWAR_TRGT_IF_LBC 0x00400000
#define LAWAR_TRGT_IF_CCSR 0x00800000
#define LAWAR_TRGT_IF_RIO 0x00c00000
#define SPRN_PMC2 0x3BA /* Performance Counter Register 2 */
#define SPRN_PMC3 0x3BD /* Performance Counter Register 3 */
#define SPRN_PMC4 0x3BE /* Performance Counter Register 4 */
-#define SPRN_SVR 0x11E /* System-On-Chip Version Register */
#define SPRN_PVR 0x11F /* Processor Version Register */
#define SPRN_RPA 0x3D6 /* Required Physical Address Register */
#define SPRN_SDA 0x3BF /* Sampled Data Address Register */
#define SPRN_SRR1 0x01B /* Save/Restore Register 1 */
#define SPRN_SRR2 0x3DE /* Save/Restore Register 2 */
#define SPRN_SRR3 0x3DF /* Save/Restore Register 3 */
+#ifdef CONFIG_BOOKE
+#define SPRN_SVR 0x3FF /* System Version Register */
+#else
+#define SPRN_SVR 0x11E /* System Version Register */
+#endif
#define SPRN_TBHI 0x3DC /* Time Base High */
#define SPRN_TBHU 0x3CC /* Time Base High User-mode */
#define SPRN_TBLO 0x3DD /* Time Base Low */
#define SPRG3 SPRN_SPRG3
#define SRR0 SPRN_SRR0 /* Save and Restore Register 0 */
#define SRR1 SPRN_SRR1 /* Save and Restore Register 1 */
+#define SVR SPRN_SVR /* System Version Register */
#define TBRL SPRN_TBRL /* Time Base Read Lower Register */
#define TBRU SPRN_TBRU /* Time Base Read Upper Register */
#define TBWL SPRN_TBWL /* Time Base Write Lower Register */
#define PVR_7400 0x000C0000
#define PVR_7410 0x800C0000
#define PVR_7450 0x80000000
-#define PVR_8540 0x80200010
-#define PVR_8560 0x80200010
+
+#define PVR_85xx 0x80200000
+#define PVR_85xx_REV1 (PVR_85xx | 0x0010)
+#define PVR_85xx_REV2 (PVR_85xx | 0x0020)
+
/*
* For the 8xx processors, all of them report the same PVR family for
#define PVR_8260_HIP7 0x80822011
#define PVR_8260_HIP7R1 0x80822013
+
+/*
+ * System Version Register
+ */
+
+/* System Version Register (SVR) field extraction */
+
+#define SVR_VER(svr) (((svr) >> 16) & 0xFFFF) /* Version field */
+#define SVR_REV(svr) (((svr) >> 0) & 0xFFFF) /* Revison field */
+
+#define SVR_FAM(svr) (((svr) >> 20) & 0xFFF) /* Family field */
+#define SVR_MEM(svr) (((svr) >> 16) & 0xF) /* Member field */
+
+#define SVR_MAJ(svr) (((svr) >> 4) & 0xF) /* Major revision field*/
+#define SVR_MIN(svr) (((svr) >> 0) & 0xF) /* Minor revision field*/
+
+
+/*
+ * SVR_VER() Version Values
+ */
+
+#define SVR_8540 0x8030
+#define SVR_8560 0x8070
+#define SVR_8555 0x8079
+#define SVR_8541 0x807A
+
+
/* I am just adding a single entry for 8260 boards. I think we may be
* able to combine mbx, fads, rpxlite, bseip, and classic into a single
* generic 8xx as well. The boards containing these processors are either
defined (CONFIG_74xx_7xx) || \
defined (CONFIG_74x) || \
defined (CONFIG_75x) || \
- defined (CONFIG_74xx)
+ defined (CONFIG_74xx) || \
+ defined(CONFIG_MPC85xx)
unsigned char in8(unsigned int);
void out8(unsigned int, unsigned char);
unsigned short in16(unsigned int);
void ppcDcbf(unsigned long value);
void ppcDcbi(unsigned long value);
void ppcSync(void);
+void ppcDcbz(unsigned long value);
#endif
/* $(CPU)/cpu.c */
/*
+ * Copyright 2004 Freescale Semiconductor.
* (C) Copyright 2002,2003 Motorola,Inc.
* Xianghua Xiao <X.Xiao@motorola.com>
*
* MA 02111-1307 USA
*/
-/* mpc8540ads board configuration file */
-/* please refer to doc/README.mpc85xxads for more info */
-/* make sure you change the MAC address and other network params first,
- * search for CONFIG_ETHADDR,CONFIG_SERVERIP,etc in this file
+/*
+ * mpc8540ads board configuration file
+ *
+ * Please refer to doc/README.mpc85xx for more info.
+ *
+ * Make sure you change the MAC address and other network params first,
+ * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/* High Level Configuration Options */
-#define CONFIG_BOOKE 1 /* BOOKE */
-#define CONFIG_E500 1 /* BOOKE e500 family */
-#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */
-#define CONFIG_MPC85xx_REV1 1 /* MPC85xx Rev 1 Chip */
-#define CONFIG_MPC8540 1 /* MPC8540 specific */
-#define CONFIG_MPC8540ADS 1 /* MPC8540ADS board specific*/
-
-#undef CONFIG_PCI /* pci ethernet support */
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#define CONFIG_BOOKE 1 /* BOOKE */
+#define CONFIG_E500 1 /* BOOKE e500 family */
+#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */
+#define CONFIG_MPC8540 1 /* MPC8540 specific */
+#define CONFIG_MPC8540ADS 1 /* MPC8540ADS board specific */
+
+#define CONFIG_PCI
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
+#define CONFIG_DDR_ECC /* only for ECC DDR module */
+#define CONFIG_DDR_DLL /* possible DLL fix needed */
+#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
-#if defined(CONFIG_MPC85xx_REV1)
-#define CONFIG_DDR_DLL /* possible DLL fix needed */
-#endif
-
-/* Using Localbus SDRAM to emulate flash before we can program the flash,
- * normally you only need a flash-boot image(u-boot.bin),if unsure undef this.
+/*
+ * Use Localbus SDRAM to emulate flash before we can program the flash.
+ * Normally you need a flash-boot image(u-boot.bin).
+ * If unsure #undef this.
*/
#undef CONFIG_RAM_AS_FLASH
-#if !defined(CONFIG_PCI) /* some PCI card is 33Mhz only */
-#define CONFIG_SYS_CLK_FREQ 66000000 /* sysclk for MPC85xx */
-#else
-#define CONFIG_SYS_CLK_FREQ 33000000 /* most pci cards are 33Mhz */
-#endif
+/*
+ * sysclk for MPC85xx
+ *
+ * Two valid values are:
+ * 33000000
+ * 66000000
+ *
+ * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
+ * is likely the desired value here. The board, however, can run and
+ * defaults to 66Mhz. In any event, this value must match the settings
+ * of SW15[1] and SW17[8], and likely SW6[0:1], the SYSCLK as well.
+ *
+ * SW17[8] ------+ SW6
+ * SW15[1] ----+ | [0:1]
+ * V V V V
+ * 33MHz 1 1 1 0
+ * 66MHz 0 0 0 1
+ */
+
+#define CONFIG_SYS_CLK_FREQ 66000000
-#if !defined(CONFIG_SPD_EEPROM) /* manually set up DDR parameters */
-#define CONFIG_DDR_SETTING
+
+#if !defined(CONFIG_SPD_EEPROM)
+#define CONFIG_DDR_SETTING /* manually set up DDR parameters */
#endif
-/* below can be toggled for performance analysis. otherwise use default */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#undef CONFIG_BTB /* toggle branch predition */
-#undef CONFIG_ADDR_STREAMING /* toggle addr streaming */
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
+#define CONFIG_BTB /* toggle branch predition */
+#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-#undef CFG_DRAM_TEST /* memory test, takes time */
-#define CFG_MEMTEST_START 0x00200000 /* memtest works on */
+#undef CFG_DRAM_TEST /* memory test, takes time */
+#define CFG_MEMTEST_START 0x00200000 /* memtest region */
#define CFG_MEMTEST_END 0x00400000
-#if defined(CONFIG_PCI) && defined(CONFIG_TSEC_ENET)
-#error "You can only use either PCI Ethernet Card or TSEC Ethernet, not both."
-#endif
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
-#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
-#define CFG_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */
-#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
+#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
-#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
+#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
-#define CFG_SDRAM_SIZE 128 /* DDR is now 128MB */
+#define CFG_SDRAM_SIZE 128 /* DDR is 128MB */
+/*
+ * SDRAM on the Local Bus
+ */
#if defined(CONFIG_RAM_AS_FLASH)
#define CFG_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */
#else
-#define CFG_LBC_SDRAM_BASE 0xf8000000 /* Localbus SDRAM */
+#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
#endif
-#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
+#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 16M */
+#define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 16M */
#define CFG_BR0_PRELIM 0xf8001801 /* port size 32bit */
#else /* Boot from real Flash */
-#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */
-#define CFG_BR0_PRELIM 0xff001801 /* port size 32bit */
+#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */
+#define CFG_BR0_PRELIM 0xff001801 /* port size 32bit */
#endif
-#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Flash */
-#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
-#define CFG_MAX_FLASH_SECT 64 /* sectors per device */
+#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Flash */
+#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
+#define CFG_MAX_FLASH_SECT 64 /* sectors per device */
#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 60000 /* Timeout for Flash Erase (in ms)*/
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms)*/
+#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
#define CFG_RAMBOOT
#else
-#undef CFG_RAMBOOT
+#undef CFG_RAMBOOT
#endif
#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
+#undef CONFIG_CLOCKS_IN_MHZ
+
#if defined(CONFIG_DDR_SETTING)
-#define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */
+#define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */
#define CFG_DDR_CS0_CONFIG 0x80000002
#define CFG_DDR_TIMING_1 0x37344321
-#define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning*/
-#define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR*/
-#define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
-#define CFG_DDR_INTERVAL 0x05200100 /* autocharge,no open page*/
+#define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
+#define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
+#define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
+#define CFG_DDR_INTERVAL 0x05200100 /* autocharge,no open page */
#endif
-#undef CONFIG_CLOCKS_IN_MHZ
-/* local bus definitions */
-#define CFG_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */
+/*
+ * Local Bus Definitions
+ */
+
+/*
+ * Base Register 2 and Option Register 2 configure SDRAM.
+ * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
+ *
+ * For BR2, need:
+ * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
+ * port-size = 32-bits = BR2[19:20] = 11
+ * no parity checking = BR2[21:22] = 00
+ * SDRAM for MSEL = BR2[24:26] = 011
+ * Valid = BR[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
+ *
+ * FIXME: CFG_LBC_SDRAM_BASE should be masked and OR'ed into
+ * FIXME: the top 17 bits of BR2.
+ */
+
+#define CFG_BR2_PRELIM 0xf0001861
+
+/*
+ * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64.
+ *
+ * For OR2, need:
+ * 64MB mask for AM, OR2[0:7] = 1111 1100
+ * XAM, OR2[17:18] = 11
+ * 9 columns OR2[19-21] = 010
+ * 13 rows OR2[23-25] = 100
+ * EAD set for extra time OR[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
+ */
+
#define CFG_OR2_PRELIM 0xfc006901
-#define CFG_LBC_LCRR 0x00030004 /* local bus freq divider*/
-#define CFG_LBC_LBCR 0x00000000
-#define CFG_LBC_LSRT 0x20000000
-#define CFG_LBC_MRTPR 0x20000000
-#define CFG_LBC_LSDMR_1 0x2861b723
-#define CFG_LBC_LSDMR_2 0x0861b723
-#define CFG_LBC_LSDMR_3 0x0861b723
-#define CFG_LBC_LSDMR_4 0x1861b723
-#define CFG_LBC_LSDMR_5 0x4061b723
+
+#define CFG_LBC_LCRR 0x00030004 /* LB clock ratio reg */
+#define CFG_LBC_LBCR 0x00000000 /* LB config reg */
+#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
+#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer prescal*/
+
+/*
+ * LSDMR masks
+ */
+#define CFG_LBC_LSDMR_RFEN (1 << (31 - 1))
+#define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10))
+#define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10))
+#define CFG_LBC_LSDMR_RFCR5 (3 << (31 - 16))
+#define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16))
+#define CFG_LBC_LSDMR_PRETOACT3 (3 << (31 - 19))
+#define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19))
+#define CFG_LBC_LSDMR_ACTTORW3 (3 << (31 - 22))
+#define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22))
+#define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22))
+#define CFG_LBC_LSDMR_BL8 (1 << (31 - 23))
+#define CFG_LBC_LSDMR_WRC2 (2 << (31 - 27))
+#define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27))
+#define CFG_LBC_LSDMR_BUFCMD (1 << (31 - 29))
+#define CFG_LBC_LSDMR_CL3 (3 << (31 - 31))
+
+#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4))
+
+#define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_BSMA1516 \
+ | CFG_LBC_LSDMR_RFCR5 \
+ | CFG_LBC_LSDMR_PRETOACT3 \
+ | CFG_LBC_LSDMR_ACTTORW3 \
+ | CFG_LBC_LSDMR_BL8 \
+ | CFG_LBC_LSDMR_WRC2 \
+ | CFG_LBC_LSDMR_CL3 \
+ | CFG_LBC_LSDMR_RFEN \
+ )
+
+/*
+ * SDRAM Controller configuration sequence.
+ */
+#define CFG_LBC_LSDMR_1 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_PCHALL) /*0x2861b723*/
+#define CFG_LBC_LSDMR_2 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_ARFRSH) /*0x0861b723*/
+#define CFG_LBC_LSDMR_3 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_ARFRSH) /*0x0861b723*/
+#define CFG_LBC_LSDMR_4 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_MRW) /*0x1861b723*/
+#define CFG_LBC_LSDMR_5 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_NORMAL) /*0x4061b723*/
+
#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */
+#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */
#else
-#define CFG_BR4_PRELIM 0xfc000801 /* 32KB, 8-bit wide for ADS config reg */
+#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */
#endif
#define CFG_OR4_PRELIM 0xffffe1f1
#define CFG_BCSR (CFG_BR4_PRELIM & 0xffff8000)
#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
+#define CFG_INIT_RAM_LOCK 1
+#define CFG_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */
+#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CFG_NS16550
#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE 1
+#define CFG_NS16550_REG_SIZE 1
#define CFG_NS16550_CLK get_bus_freq(0)
-#define CONFIG_BAUDRATE 115200
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
-#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
+#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
+#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
/* Use the HUSH parser */
#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
+#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+
+/* RapidIO MMU */
+#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */
+#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE
+#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CFG_PCI1_MEM_BASE 0x80000000
+#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCI1_IO_BASE 0xe2000000
+#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
+#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
-/* General PCI */
-#define CFG_PCI_MEM_BASE 0xe0000000
-#define CFG_PCI_MEM_PHYS 0xe0000000
-#define CFG_PCI_MEM_SIZE 0x10000000
#if defined(CONFIG_PCI)
+
#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
#undef CONFIG_EEPRO100
-#define CONFIG_TULIP
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- #if !defined(CONFIG_PCI_PNP)
- #define PCI_ENET0_IOADDR 0xe0000000
- #define PCI_ENET0_MEMADDR 0xe0000000
- #define PCI_IDSEL_NUMBER 0x0c /*slot0->3(IDSEL)=12->15*/
- #endif
-#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
-#if defined(CONFIG_MPC85xx_REV1) /* Errata PCI 8 */
- #define CFG_PCI_SUBSYS_DEVICEID 0x0003
-#else
- #define CFG_PCI_SUBSYS_DEVICEID 0x0008
+#undef CONFIG_TULIP
+
+#if !defined(CONFIG_PCI_PNP)
+ #define PCI_ENET0_IOADDR 0xe0000000
+ #define PCI_ENET0_MEMADDR 0xe0000000
+ #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
#endif
-#elif defined(CONFIG_TSEC_ENET)
-#define CONFIG_NET_MULTI 1
-#define CONFIG_PHY_M88E1011 1 /* GigaBit Ether PHY */
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 8 /* PHY address */
+
+#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
+
+#endif /* CONFIG_PCI */
+
+
+#if defined(CONFIG_TSEC_ENET)
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI 1
#endif
-/* Environment */
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_MPC85XX_TSEC1 1
+#define CONFIG_MPC85XX_TSEC2 1
+#define CONFIG_MPC85XX_FEC 1
+#define TSEC1_PHY_ADDR 0
+#define TSEC2_PHY_ADDR 1
+#define FEC_PHY_ADDR 3
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+#define FEC_PHYIDX 0
+#define CONFIG_ETHPRIME "MOTO ENET0"
+
+#endif /* CONFIG_TSEC_ENET */
+
+
+/*
+ * Environment
+ */
#ifndef CFG_RAMBOOT
#if defined(CONFIG_RAM_AS_FLASH)
#define CFG_ENV_IS_NOWHERE
#else
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
- #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
+ #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
#endif
#define CFG_ENV_SIZE 0x2000
#else
-#define CFG_NO_FLASH 1 /* Flash is not usable now */
-#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+#define CFG_NO_FLASH 1 /* Flash is not usable now */
+#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
#define CFG_ENV_SIZE 0x2000
#endif
-#define CONFIG_BOOTARGS "root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8540ads-003:eth0:off console=ttyS0,115200"
-/*#define CONFIG_BOOTARGS "root=/dev/ram rw console=ttyS0,115200"*/
-#define CONFIG_BOOTCOMMAND "bootm 0xff300000 0xff700000"
-#define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH)
#if defined(CONFIG_PCI)
- #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PING | CFG_CMD_PCI | CFG_CMD_I2C ) & \
- ~(CFG_CMD_ENV | CFG_CMD_LOADS ))
+ #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
+ | CFG_CMD_PING \
+ | CFG_CMD_PCI \
+ | CFG_CMD_I2C) \
+ & \
+ ~(CFG_CMD_ENV \
+ | CFG_CMD_LOADS))
#else
- #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PING | CFG_CMD_I2C ) & \
- ~(CFG_CMD_ENV | \
- CFG_CMD_LOADS ))
+ #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
+ | CFG_CMD_PING \
+ | CFG_CMD_I2C) \
+ & \
+ ~(CFG_CMD_ENV \
+ | CFG_CMD_LOADS))
#endif
#else
#if defined(CONFIG_PCI)
- #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI | CFG_CMD_PING | CFG_CMD_I2C )
+ #define CONFIG_COMMANDS (CONFIG_CMD_DFL \
+ | CFG_CMD_PCI \
+ | CFG_CMD_PING \
+ | CFG_CMD_I2C)
#else
- #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PING | CFG_CMD_I2C )
+ #define CONFIG_COMMANDS (CONFIG_CMD_DFL \
+ | CFG_CMD_PING \
+ | CFG_CMD_I2C)
#endif
#endif
+
#include <cmd_confdefs.h>
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "MPC8540ADS=> " /* Monitor Command Prompt */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_LOAD_ADDR 0x2000000 /* default load address */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+ #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+ #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
+
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_LOAD_ADDR 0x1000000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
/* Cache Configuration */
-#define CFG_DCACHE_SIZE 32768
+#define CFG_DCACHE_SIZE 32768
#define CFG_CACHELINE_SIZE 32
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
#endif
/*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
-/* NOTE: change below for your network setting!!! */
+/*****************************/
+/* Environment Configuration */
+/*****************************/
+
+/* The mac addresses for all ethernet interface */
#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_ETHADDR 00:01:af:07:9b:8a
-#define CONFIG_ETH1ADDR 00:01:af:07:9b:8b
-#define CONFIG_ETH2ADDR 00:01:af:07:9b:8c
+#define CONFIG_ETHADDR 00:E0:0C:00:00:FD
+#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD
+#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD
#endif
-#define CONFIG_SERVERIP 163.12.64.52
-#define CONFIG_IPADDR 10.82.0.105
-#define CONFIG_GATEWAYIP 10.82.1.254
-#define CONFIG_NETMASK 255.255.254.0
-#define CONFIG_HOSTNAME MPC8560ADS_PILOT_003
-#define CONFIG_ROOTPATH /home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx
-#define CONFIG_BOOTFILE pImage
+#define CONFIG_IPADDR 192.168.1.253
+
+#define CONFIG_HOSTNAME unknown
+#define CONFIG_ROOTPATH /nfsroot
+#define CONFIG_BOOTFILE your.uImage
+
+#define CONFIG_SERVERIP 192.168.1.1
+#define CONFIG_GATEWAYIP 192.168.1.1
+#define CONFIG_NETMASK 255.255.255.0
+
+#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
+
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=400000\0" \
+ "ramdiskfile=your.ramdisk.u-boot\0"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "bootm $loadaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "bootm $loadaddr $ramdiskaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
#endif /* __CONFIG_H */
/*
+ * Copyright 2004 Freescale Semiconductor.
* (C) Copyright 2002,2003 Motorola,Inc.
* Xianghua Xiao <X.Xiao@motorola.com>
*
* MA 02111-1307 USA
*/
-/* mpc8560ads board configuration file */
-/* please refer to doc/README.mpc85xx for more info */
-/* make sure you change the MAC address and other network params first,
- * search for CONFIG_ETHADDR,CONFIG_SERVERIP,etc in this file
+/*
+ * mpc8560ads board configuration file
+ *
+ * Please refer to doc/README.mpc85xx for more info.
+ *
+ * Make sure you change the MAC address and other network params first,
+ * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/* High Level Configuration Options */
-#define CONFIG_BOOKE 1 /* BOOKE */
-#define CONFIG_E500 1 /* BOOKE e500 family */
-#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */
-#define CONFIG_MPC85xx_REV1 1 /* MPC85xx Rev 1.0 chip */
-#define CONFIG_MPC8560 1 /* MPC8560 specific */
-#define CONFIG_MPC8560ADS 1 /* MPC8560ADS board specific */
-
-#undef CONFIG_PCI /* pci ethernet support */
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
-#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */
+#define CONFIG_BOOKE 1 /* BOOKE */
+#define CONFIG_E500 1 /* BOOKE e500 family */
+#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */
+#define CONFIG_MPC8560 1 /* MPC8560 specific */
+#define CONFIG_MPC8560ADS 1 /* MPC8560ADS board specific */
+
+#define CONFIG_PCI
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
+#define CONFIG_DDR_ECC /* only for ECC DDR module */
+#define CONFIG_DDR_DLL /* possible DLL fix needed */
+#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
-#if defined(CONFIG_MPC85xx_REV1)
-#define CONFIG_DDR_DLL /* possible DLL fix needed */
-#endif
-
-/* Using Localbus SDRAM to emulate flash before we can program the flash,
- * normally you need a flash-boot image(u-boot.bin), if so undef this.
+/*
+ * Use Localbus SDRAM to emulate flash before we can program the flash.
+ * Normally you need a flash-boot image(u-boot.bin).
+ * If unsure #undef this.
*/
#undef CONFIG_RAM_AS_FLASH
-#if !defined(CONFIG_PCI) /* some PCI card is 33Mhz only */
-#define CONFIG_SYS_CLK_FREQ 66000000/* sysclk for MPC85xx */
-#else
-#define CONFIG_SYS_CLK_FREQ 33000000/* most pci cards are 33Mhz */
-#endif
+/*
+ * sysclk for MPC85xx
+ *
+ * Two valid values are:
+ * 33000000
+ * 66000000
+ *
+ * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
+ * is likely the desired value here. The board, however, can run and
+ * defaults to 66Mhz. In any event, this value must match the settings
+ * of SW15[1] and SW17[8], and likely SW6[0:1], the SYSCLK as well.
+ *
+ * SW17[8] ------+ SW6
+ * SW15[1] ----+ | [0:1]
+ * V V V V
+ * 33MHz 1 1 1 0
+ * 66MHz 0 0 0 1
+ */
+
+#define CONFIG_SYS_CLK_FREQ 66000000
-#if !defined(CONFIG_SPD_EEPROM) /* manually set up DDR parameters */
-#define CONFIG_DDR_SETTING
+
+#if !defined(CONFIG_SPD_EEPROM)
+#define CONFIG_DDR_SETTING /* manually set up DDR parameters */
#endif
-/* below can be toggled for performance analysis. otherwise use default */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#undef CONFIG_BTB /* toggle branch predition */
-#undef CONFIG_ADDR_STREAMING /* toggle addr streaming */
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
+#define CONFIG_BTB /* toggle branch predition */
+#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-#undef CFG_DRAM_TEST /* memory test, takes time */
-#define CFG_MEMTEST_START 0x00200000 /* memtest region */
+#define CFG_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */
+
+#undef CFG_DRAM_TEST /* memory test, takes time */
+#define CFG_MEMTEST_START 0x00200000 /* memtest region */
#define CFG_MEMTEST_END 0x00400000
-#if (defined(CONFIG_PCI) && defined(CONFIG_TSEC_ENET) || \
- defined(CONFIG_PCI) && defined(CONFIG_ETHER_ON_FCC) || \
- defined(CONFIG_TSEC_ENET) && defined(CONFIG_ETHER_ON_FCC))
-#error "You can only use ONE of PCI Ethernet Card or TSEC Ethernet or CPM FCC."
-#endif
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
-#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
-#define CFG_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */
-#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
+#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
-#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
+#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
-#define CFG_SDRAM_SIZE 128 /* DDR is 128MB */
+#define CFG_SDRAM_SIZE 128 /* DDR is 128MB */
+/*
+ * SDRAM on the Local Bus
+ */
#if defined(CONFIG_RAM_AS_FLASH)
#define CFG_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */
#else
-#define CFG_LBC_SDRAM_BASE 0xf8000000 /* Localbus SDRAM */
+#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
#endif
-#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
+#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 16M */
-#define CFG_BR0_PRELIM 0xf8001801 /* port size 32bit */
+#define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 16M */
+#define CFG_BR0_PRELIM 0xf8001801 /* port size 32bit */
#else /* Boot from real Flash */
-#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */
-#define CFG_BR0_PRELIM 0xff001801 /* port size 32bit */
+#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */
+#define CFG_BR0_PRELIM 0xff001801 /* port size 32bit */
#endif
-#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Flash */
-#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
-#define CFG_MAX_FLASH_SECT 64 /* sectors per device */
+#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Flash */
+#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
+#define CFG_MAX_FLASH_SECT 64 /* sectors per device */
#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 60000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
#define CFG_RAMBOOT
#else
-#undef CFG_RAMBOOT
+#undef CFG_RAMBOOT
#endif
-#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
+#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
+
+#undef CONFIG_CLOCKS_IN_MHZ
#if defined(CONFIG_DDR_SETTING)
#define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */
#define CFG_DDR_CS0_CONFIG 0x80000002
#define CFG_DDR_TIMING_1 0x37344321
-#define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning*/
-#define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR*/
-#define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
-#define CFG_DDR_INTERVAL 0x05200100 /* autocharge,no open page*/
+#define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
+#define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
+#define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
+#define CFG_DDR_INTERVAL 0x05200100 /* autocharge,no open page */
#endif
-#undef CONFIG_CLOCKS_IN_MHZ
-/* local bus definitions */
-#define CFG_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */
+/*
+ * Local Bus Definitions
+ */
+
+/*
+ * Base Register 2 and Option Register 2 configure SDRAM.
+ * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
+ *
+ * For BR2, need:
+ * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
+ * port-size = 32-bits = BR2[19:20] = 11
+ * no parity checking = BR2[21:22] = 00
+ * SDRAM for MSEL = BR2[24:26] = 011
+ * Valid = BR[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
+ *
+ * FIXME: CFG_LBC_SDRAM_BASE should be masked and OR'ed into
+ * FIXME: the top 17 bits of BR2.
+ */
+
+#define CFG_BR2_PRELIM 0xf0001861
+
+/*
+ * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64.
+ *
+ * For OR2, need:
+ * 64MB mask for AM, OR2[0:7] = 1111 1100
+ * XAM, OR2[17:18] = 11
+ * 9 columns OR2[19-21] = 010
+ * 13 rows OR2[23-25] = 100
+ * EAD set for extra time OR[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
+ */
+
#define CFG_OR2_PRELIM 0xfc006901
-#define CFG_LBC_LCRR 0x00030004 /* local bus freq */
-#define CFG_LBC_LBCR 0x00000000
-#define CFG_LBC_LSRT 0x20000000
-#define CFG_LBC_MRTPR 0x20000000
-#define CFG_LBC_LSDMR_1 0x2861b723
-#define CFG_LBC_LSDMR_2 0x0861b723
-#define CFG_LBC_LSDMR_3 0x0861b723
-#define CFG_LBC_LSDMR_4 0x1861b723
-#define CFG_LBC_LSDMR_5 0x4061b723
+
+#define CFG_LBC_LCRR 0x00030004 /* LB clock ratio reg */
+#define CFG_LBC_LBCR 0x00000000 /* LB config reg */
+#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
+#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer prescal*/
+
+/*
+ * LSDMR masks
+ */
+#define CFG_LBC_LSDMR_RFEN (1 << (31 - 1))
+#define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10))
+#define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10))
+#define CFG_LBC_LSDMR_RFCR5 (3 << (31 - 16))
+#define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16))
+#define CFG_LBC_LSDMR_PRETOACT3 (3 << (31 - 19))
+#define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19))
+#define CFG_LBC_LSDMR_ACTTORW3 (3 << (31 - 22))
+#define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22))
+#define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22))
+#define CFG_LBC_LSDMR_BL8 (1 << (31 - 23))
+#define CFG_LBC_LSDMR_WRC2 (2 << (31 - 27))
+#define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27))
+#define CFG_LBC_LSDMR_BUFCMD (1 << (31 - 29))
+#define CFG_LBC_LSDMR_CL3 (3 << (31 - 31))
+
+#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4))
+
+#define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_BSMA1516 \
+ | CFG_LBC_LSDMR_RFCR5 \
+ | CFG_LBC_LSDMR_PRETOACT3 \
+ | CFG_LBC_LSDMR_ACTTORW3 \
+ | CFG_LBC_LSDMR_BL8 \
+ | CFG_LBC_LSDMR_WRC2 \
+ | CFG_LBC_LSDMR_CL3 \
+ | CFG_LBC_LSDMR_RFEN \
+ )
+
+/*
+ * SDRAM Controller configuration sequence.
+ */
+#define CFG_LBC_LSDMR_1 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_PCHALL) /*0x2861b723*/
+#define CFG_LBC_LSDMR_2 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_ARFRSH) /*0x0861b723*/
+#define CFG_LBC_LSDMR_3 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_ARFRSH) /*0x0861b723*/
+#define CFG_LBC_LSDMR_4 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_MRW) /*0x1861b723*/
+#define CFG_LBC_LSDMR_5 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_NORMAL) /*0x4061b723*/
+
#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */
+#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */
#else
-#define CFG_BR4_PRELIM 0xfc000801 /* 32KB, 8-bit wide for ADS config reg */
+#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */
#endif
#define CFG_OR4_PRELIM 0xffffe1f1
#define CFG_BCSR (CFG_BR4_PRELIM & 0xffff8000)
#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
+#define CFG_INIT_RAM_LOCK 1
+#define CFG_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */
+#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/* Serial Port */
-#define CONFIG_CONS_ON_SCC /* define if console on SCC */
-#undef CONFIG_CONS_NONE /* define if console on something else */
-#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
+#define CONFIG_CONS_ON_SCC /* define if console on SCC */
+#undef CONFIG_CONS_NONE /* define if console on something else */
+#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
-#define CONFIG_BAUDRATE 115200
+#define CONFIG_BAUDRATE 115200
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
/* Use the HUSH parser */
#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
+#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-#define CFG_PCI_MEM_BASE 0xe0000000
-#define CFG_PCI_MEM_PHYS 0xe0000000
-#define CFG_PCI_MEM_SIZE 0x10000000
+/* RapidIO MMU */
+#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */
+#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE
+#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CFG_PCI1_MEM_BASE 0x80000000
+#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCI1_IO_BASE 0xe2000000
+#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
+#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
+
+#if defined(CONFIG_PCI)
-#if defined(CONFIG_PCI) /* PCI Ethernet card */
#define CONFIG_NET_MULTI
-#define CONFIG_EEPRO100
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
#undef CONFIG_TULIP
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- #if !defined(CONFIG_PCI_PNP)
- #define PCI_ENET0_IOADDR 0xe0000000
- #define PCI_ENET0_MEMADDR 0xe0000000
- #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
- #endif
-#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
-#if defined(CONFIG_MPC85xx_REV1) /* Errata PCI 7 */
- #define CFG_PCI_SUBSYS_DEVICEID 0x0003
-#else
- #define CFG_PCI_SUBSYS_DEVICEID 0x0009
+
+#if !defined(CONFIG_PCI_PNP)
+ #define PCI_ENET0_IOADDR 0xe0000000
+ #define PCI_ENET0_MEMADDR 0xe0000000
+ #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
#endif
-#elif defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */
-#define CONFIG_NET_MULTI 1
-#define CONFIG_PHY_M88E1011 1 /* GigaBit Ether PHY */
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 8 /* PHY address */
+
+#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
+
+#endif /* CONFIG_PCI */
+
+
+#if defined(CONFIG_TSEC_ENET)
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI 1
+#endif
+
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_MPC85XX_TSEC1 1
+#define CONFIG_MPC85XX_TSEC2 1
+#undef CONFIG_MPC85XX_FEC
+#define TSEC1_PHY_ADDR 0
+#define TSEC2_PHY_ADDR 1
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+#define CONFIG_ETHPRIME "MOTO ENET0"
+
#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */
-#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
-#undef CONFIG_ETHER_NONE /* define if ether on something else */
-#define CONFIG_ETHER_INDEX 2 /* which channel for ether */
- #if (CONFIG_ETHER_INDEX == 2)
+
+#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
+#undef CONFIG_ETHER_NONE /* define if ether on something else */
+#define CONFIG_ETHER_INDEX 2 /* which channel for ether */
+
+#if (CONFIG_ETHER_INDEX == 2)
/*
* - Rx-CLK is CLK13
* - Tx-CLK is CLK14
* - Select bus for bd/buffers
* - Full duplex
*/
- #define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
- #define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
- #define CFG_CPMFCR_RAMTYPE 0
- #define CFG_FCC_PSMR (FCC_PSMR_FDE)
+ #define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
+ #define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
+ #define CFG_CPMFCR_RAMTYPE 0
+ #define CFG_FCC_PSMR (FCC_PSMR_FDE)
#define FETH2_RST 0x01
- #elif (CONFIG_ETHER_INDEX == 3)
+#elif (CONFIG_ETHER_INDEX == 3)
/* need more definitions here for FE3 */
#define FETH3_RST 0x80
- #endif /* CONFIG_ETHER_INDEX */
+#endif /* CONFIG_ETHER_INDEX */
+
#define CONFIG_MII /* MII PHY management */
-#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
+#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
+
/*
* GPIO pins used for bit-banged MII communications
*/
else iop->pdat &= ~0x00200000
#define MIIDELAY udelay(1)
+
#endif
-/* Environment */
+
+/*
+ * Environment
+ */
#ifndef CFG_RAMBOOT
#if defined(CONFIG_RAM_AS_FLASH)
#define CFG_ENV_IS_NOWHERE
#else
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
- #define CFG_ENV_SECT_SIZE 0x40000 /* 128K(one sector) for env */
+ #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
#endif
#define CFG_ENV_SIZE 0x2000
#else
-#define CFG_NO_FLASH 1 /* Flash is not usable now */
-#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+#define CFG_NO_FLASH 1 /* Flash is not usable now */
+#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
#define CFG_ENV_SIZE 0x2000
#endif
-#define CONFIG_BOOTARGS "root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8560ads-003:eth0:off console=ttyS0,115200"
-/*#define CONFIG_BOOTARGS "root=/dev/ram rw console=ttyS0,115200"*/
-#define CONFIG_BOOTCOMMAND "bootm 0xff400000 0xff700000"
-#define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH)
#if defined(CONFIG_PCI)
- #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PCI | \
- CFG_CMD_PING | CFG_CMD_I2C) & \
- ~(CFG_CMD_ENV | \
- CFG_CMD_LOADS ))
+ #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
+ | CFG_CMD_PCI \
+ | CFG_CMD_PING \
+ | CFG_CMD_I2C) \
+ & \
+ ~(CFG_CMD_ENV \
+ | CFG_CMD_LOADS))
#elif defined(CONFIG_TSEC_ENET)
- #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PING | \
- CFG_CMD_I2C ) & \
- ~(CFG_CMD_ENV))
+ #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
+ | CFG_CMD_PING \
+ | CFG_CMD_I2C) \
+ & ~(CFG_CMD_ENV))
#elif defined(CONFIG_ETHER_ON_FCC)
- #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_MII | \
- CFG_CMD_PING | CFG_CMD_I2C) & \
- ~(CFG_CMD_ENV))
+ #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
+ | CFG_CMD_MII \
+ | CFG_CMD_PING \
+ | CFG_CMD_I2C) \
+ & ~(CFG_CMD_ENV))
#endif
#else
#if defined(CONFIG_PCI)
- #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI | \
- CFG_CMD_PING | CFG_CMD_I2C)
+ #define CONFIG_COMMANDS (CONFIG_CMD_DFL \
+ | CFG_CMD_PCI \
+ | CFG_CMD_PING \
+ | CFG_CMD_I2C)
#elif defined(CONFIG_TSEC_ENET)
- #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PING | \
- CFG_CMD_I2C)
+ #define CONFIG_COMMANDS (CONFIG_CMD_DFL \
+ | CFG_CMD_PING \
+ | CFG_CMD_I2C)
#elif defined(CONFIG_ETHER_ON_FCC)
- #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_MII | \
- CFG_CMD_PING | CFG_CMD_I2C)
+ #define CONFIG_COMMANDS (CONFIG_CMD_DFL \
+ | CFG_CMD_MII \
+ | CFG_CMD_PING \
+ | CFG_CMD_I2C)
#endif
#endif
+
#include <cmd_confdefs.h>
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "MPC8560ADS=> " /* Monitor Command Prompt */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_LOAD_ADDR 0x1000000 /* default load address */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+ #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+ #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
+
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_LOAD_ADDR 0x1000000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
/* Cache Configuration */
#define CFG_DCACHE_SIZE 32768
#define CFG_CACHELINE_SIZE 32
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
#endif
/*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
-/*Note: change below for your network setting!!! */
+/* The mac addresses for all ethernet interface */
#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
-#define CONFIG_ETHADDR 00:01:af:07:9b:8a
-#define CONFIG_ETH1ADDR 00:01:af:07:9b:8b
-#define CONFIG_ETH2ADDR 00:01:af:07:9b:8c
+#define CONFIG_ETHADDR 00:E0:0C:00:00:FD
+#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD
+#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD
#endif
-#define CONFIG_SERVERIP 163.12.64.52
-#define CONFIG_IPADDR 10.82.0.105
-#define CONFIG_GATEWAYIP 10.82.1.254
-#define CONFIG_NETMASK 255.255.254.0
-#define CONFIG_HOSTNAME MPC8560ADS_PILOT_003
-#define CONFIG_ROOTPATH /home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx
-#define CONFIG_BOOTFILE pImage
+#define CONFIG_IPADDR 192.168.1.253
+
+#define CONFIG_HOSTNAME unknown
+#define CONFIG_ROOTPATH /nfsroot
+#define CONFIG_BOOTFILE your.uImage
+
+#define CONFIG_SERVERIP 192.168.1.1
+#define CONFIG_GATEWAYIP 192.168.1.1
+#define CONFIG_NETMASK 255.255.255.0
+
+#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
+
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=400000\0" \
+ "ramdiskfile=your.ramdisk.u-boot\0"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "bootm $loadaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "bootm $loadaddr $ramdiskaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
#endif /* __CONFIG_H */
/*
+ * Copyright 2004 Freescale Semiconductor.
* Copyright(c) 2003 Motorola Inc.
* Xianghua Xiao (x.xiao@motorola.com)
*/
#ifndef __MPC85xx_H__
#define __MPC85xx_H__
-#define EXC_OFF_SYS_RESET 0x0100 /* System reset */
+#define EXC_OFF_SYS_RESET 0x0100 /* System reset */
#if defined(CONFIG_E500)
#include <e500.h>
#endif
-#if defined(CONFIG_DDR_ECC)
-void dma_init(void);
-uint dma_check(void);
-int dma_xfer(void *dest, uint count, void *src);
-#endif
-/*-----------------------------------------------------------------------
- * SCCR - System Clock Control Register 9-8
+/*
+ * SCCR - System Clock Control Register, 9-8
*/
-#define SCCR_CLPD 0x00000004 /* CPM Low Power Disable */
-#define SCCR_DFBRG_MSK 0x00000003 /* Division factor of BRGCLK Mask */
+#define SCCR_CLPD 0x00000004 /* CPM Low Power Disable */
+#define SCCR_DFBRG_MSK 0x00000003 /* Division by BRGCLK Mask */
#define SCCR_DFBRG_SHIFT 0
-#define SCCR_DFBRG00 0x00000000 /* BRGCLK division by 4 */
-#define SCCR_DFBRG01 0x00000001 /* BRGCLK division by 16 (normal op.)*/
-#define SCCR_DFBRG10 0x00000002 /* BRGCLK division by 64 */
-#define SCCR_DFBRG11 0x00000003 /* BRGCLK division by 256 */
+#define SCCR_DFBRG00 0x00000000 /* BRGCLK division by 4 */
+#define SCCR_DFBRG01 0x00000001 /* BRGCLK div by 16 (normal) */
+#define SCCR_DFBRG10 0x00000002 /* BRGCLK division by 64 */
+#define SCCR_DFBRG11 0x00000003 /* BRGCLK division by 256 */
#endif /* __MPC85xx_H__ */
#endif
#if defined(CFG_GT_6426x) || defined(CONFIG_PN62) || defined(CONFIG_PPCHAMELEONEVB) || \
- defined(CONFIG_MPC8540ADS) || defined(CONFIG_MPC8560ADS) || defined(CONFIG_440_GX)
+ defined(CONFIG_MPC8540ADS) || defined(CONFIG_MPC8555CDS) || \
+ defined(CONFIG_MPC8560ADS) || defined(CONFIG_440_GX)
/* handle the 2nd ethernet address */
s = getenv ("eth1addr");
s = (*e) ? e + 1 : e;
}
#endif
-#if defined(CFG_GT_6426x) || defined(CONFIG_MPC8540ADS) || defined(CONFIG_MPC8560ADS) || \
- defined(CONFIG_440_GX)
+#if defined(CFG_GT_6426x) || defined(CONFIG_MPC8540ADS) || \
+ defined(CONFIG_MPC8555CDS) || defined(CONFIG_MPC8560ADS) || \
+ defined(CONFIG_440_GX)
/* handle the 3rd ethernet address */
s = getenv ("eth2addr");
extern int rtl8169_initialize(bd_t*);
extern int scc_initialize(bd_t*);
extern int skge_initialize(bd_t*);
-extern int tsec_initialize(bd_t*);
+extern int tsec_initialize(bd_t*, int);
static struct eth_device *eth_devices, *eth_current;
#if defined(CONFIG_SK98)
skge_initialize(bis);
#endif
-#ifdef CONFIG_TSEC_ENET
- tsec_initialize(bis);
+#if defined(CONFIG_MPC85XX_TSEC1)
+ tsec_initialize(bis, 0);
+#endif
+#if defined(CONFIG_MPC85XX_TSEC2)
+ tsec_initialize(bis, 1);
+#endif
+#if defined(CONFIG_MPC85XX_FEC)
+ tsec_initialize(bis, 2);
#endif
#if defined(CONFIG_AU1X00)
au1x00_enet_initialize(bis);
projects / project / bcm63xx / u-boot.git / commitdiff