These boards have not been converted to generic board by the deadline.
Remove them.
Signed-off-by: Simon Glass <sjg@chromium.org>
select CPU_ARM926EJS
select SUPPORT_SPL
-config ARCH_NOMADIK
- bool "ST-Ericsson Nomadik"
- select CPU_ARM926EJS
-
config ORION5X
bool "Marvell Orion"
select CPU_ARM926EJS
source "arch/arm/cpu/armv7/mx5/Kconfig"
-source "arch/arm/mach-nomadik/Kconfig"
-
source "arch/arm/cpu/armv7/omap3/Kconfig"
source "arch/arm/cpu/armv7/omap4/Kconfig"
+++ /dev/null
-if ARCH_NOMADIK
-
-choice
- prompt "Nomadik board select"
- optional
-
-config NOMADIK_NHK8815
- bool "ST 8815 Nomadik Hardware Kit"
-
-endchoice
-
-config SYS_SOC
- default "nomadik"
-
-source "board/st/nhk8815/Kconfig"
-
-endif
+++ /dev/null
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = timer.o gpio.o
-obj-y += reset.o
+++ /dev/null
-/*
- * (C) Copyright 2009 Alessandro Rubini
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/gpio.h>
-
-static unsigned long gpio_base[4] = {
- NOMADIK_GPIO0_BASE,
- NOMADIK_GPIO1_BASE,
- NOMADIK_GPIO2_BASE,
- NOMADIK_GPIO3_BASE
-};
-
-enum gpio_registers {
- GPIO_DAT = 0x00, /* data register */
- GPIO_DATS = 0x04, /* data set */
- GPIO_DATC = 0x08, /* data clear */
- GPIO_PDIS = 0x0c, /* pull disable */
- GPIO_DIR = 0x10, /* direction */
- GPIO_DIRS = 0x14, /* direction set */
- GPIO_DIRC = 0x18, /* direction clear */
- GPIO_AFSLA = 0x20, /* alternate function select A */
- GPIO_AFSLB = 0x24, /* alternate function select B */
-};
-
-static inline unsigned long gpio_to_base(int gpio)
-{
- return gpio_base[gpio / 32];
-}
-
-static inline u32 gpio_to_bit(int gpio)
-{
- return 1 << (gpio & 0x1f);
-}
-
-void nmk_gpio_af(int gpio, int alternate_function)
-{
- unsigned long base = gpio_to_base(gpio);
- u32 bit = gpio_to_bit(gpio);
- u32 afunc, bfunc;
-
- /* alternate function is 0..3, with one bit per register */
- afunc = readl(base + GPIO_AFSLA) & ~bit;
- bfunc = readl(base + GPIO_AFSLB) & ~bit;
- if (alternate_function & 1) afunc |= bit;
- if (alternate_function & 2) bfunc |= bit;
- writel(afunc, base + GPIO_AFSLA);
- writel(bfunc, base + GPIO_AFSLB);
-}
-
-void nmk_gpio_dir(int gpio, int dir)
-{
- unsigned long base = gpio_to_base(gpio);
- u32 bit = gpio_to_bit(gpio);
-
- if (dir)
- writel(bit, base + GPIO_DIRS);
- else
- writel(bit, base + GPIO_DIRC);
-}
-
-void nmk_gpio_set(int gpio, int val)
-{
- unsigned long base = gpio_to_base(gpio);
- u32 bit = gpio_to_bit(gpio);
-
- if (val)
- writel(bit, base + GPIO_DATS);
- else
- writel(bit, base + GPIO_DATC);
-}
-
-int nmk_gpio_get(int gpio)
-{
- unsigned long base = gpio_to_base(gpio);
- u32 bit = gpio_to_bit(gpio);
-
- return readl(base + GPIO_DAT) & bit;
-}
+++ /dev/null
-/*
- * (C) Copyright 2009 Alessandro Rubini
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-#ifndef __NMK_GPIO_H__
-#define __NMK_GPIO_H__
-
-/*
- * These functions are called from the soft-i2c driver, but
- * are also used by board files to set output bits.
- */
-
-enum nmk_af { /* alternate function settings */
- GPIO_GPIO = 0,
- GPIO_ALT_A,
- GPIO_ALT_B,
- GPIO_ALT_C
-};
-
-extern void nmk_gpio_af(int gpio, int alternate_function);
-extern void nmk_gpio_dir(int gpio, int dir);
-extern void nmk_gpio_set(int gpio, int val);
-extern int nmk_gpio_get(int gpio);
-
-#endif /* __NMK_GPIO_H__ */
+++ /dev/null
-/*
- * (C) Copyright 2009 Alessandro Rubini
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __ASM_ARCH_MTU_H
-#define __ASM_ARCH_MTU_H
-
-/*
- * The MTU device hosts four different counters, with 4 set of
- * registers. These are register names.
- */
-
-#define MTU_IMSC 0x00 /* Interrupt mask set/clear */
-#define MTU_RIS 0x04 /* Raw interrupt status */
-#define MTU_MIS 0x08 /* Masked interrupt status */
-#define MTU_ICR 0x0C /* Interrupt clear register */
-
-/* per-timer registers take 0..3 as argument */
-#define MTU_LR(x) (0x10 + 0x10 * (x) + 0x00) /* Load value */
-#define MTU_VAL(x) (0x10 + 0x10 * (x) + 0x04) /* Current value */
-#define MTU_CR(x) (0x10 + 0x10 * (x) + 0x08) /* Control reg */
-#define MTU_BGLR(x) (0x10 + 0x10 * (x) + 0x0c) /* At next overflow */
-
-/* bits for the control register */
-#define MTU_CRn_ENA 0x80
-#define MTU_CRn_PERIODIC 0x40 /* if 0 = free-running */
-#define MTU_CRn_PRESCALE_MASK 0x0c
-#define MTU_CRn_PRESCALE_1 0x00
-#define MTU_CRn_PRESCALE_16 0x04
-#define MTU_CRn_PRESCALE_256 0x08
-#define MTU_CRn_32BITS 0x02
-#define MTU_CRn_ONESHOT 0x01 /* if 0 = wraps reloading from BGLR*/
-
-/* Other registers are usual amba/primecell registers, currently not used */
-#define MTU_ITCR 0xff0
-#define MTU_ITOP 0xff4
-
-#define MTU_PERIPH_ID0 0xfe0
-#define MTU_PERIPH_ID1 0xfe4
-#define MTU_PERIPH_ID2 0xfe8
-#define MTU_PERIPH_ID3 0xfeC
-
-#define MTU_PCELL0 0xff0
-#define MTU_PCELL1 0xff4
-#define MTU_PCELL2 0xff8
-#define MTU_PCELL3 0xffC
-
-#endif /* __ASM_ARCH_MTU_H */
+++ /dev/null
-#include <config.h>
-/*
- * Processor reset for Nomadik
- */
-
- .align 5
-.globl reset_cpu
-reset_cpu:
- ldr r0, =NOMADIK_SRC_BASE /* System and Reset Controller */
- ldr r1, =0x1
- str r1, [r0, #0x18]
-
-_loop_forever:
- b _loop_forever
+++ /dev/null
-/*
- * (C) Copyright 2009 Alessandro Rubini
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/mtu.h>
-
-/*
- * The timer is a decrementer, we'll left it free running at 2.4MHz.
- * We have 2.4 ticks per microsecond and an overflow in almost 30min
- */
-#define TIMER_CLOCK (24 * 100 * 1000)
-#define COUNT_TO_USEC(x) ((x) * 5 / 12) /* overflows at 6min */
-#define USEC_TO_COUNT(x) ((x) * 12 / 5) /* overflows at 6min */
-#define TICKS_PER_HZ (TIMER_CLOCK / CONFIG_SYS_HZ)
-#define TICKS_TO_HZ(x) ((x) / TICKS_PER_HZ)
-
-/* macro to read the decrementing 32 bit timer as an increasing count */
-#define READ_TIMER() (0 - readl(CONFIG_SYS_TIMERBASE + MTU_VAL(0)))
-
-/* Configure a free-running, auto-wrap counter with no prescaler */
-int timer_init(void)
-{
- ulong val;
-
- writel(MTU_CRn_ENA | MTU_CRn_PRESCALE_1 | MTU_CRn_32BITS,
- CONFIG_SYS_TIMERBASE + MTU_CR(0));
-
- /* Reset the timer */
- writel(0, CONFIG_SYS_TIMERBASE + MTU_LR(0));
- /*
- * The load-register isn't really immediate: it changes on clock
- * edges, so we must wait for our newly-written value to appear.
- * Since we might miss reading 0, wait for any change in value.
- */
- val = READ_TIMER();
- while (READ_TIMER() == val)
- ;
-
- return 0;
-}
-
-/* Return how many HZ passed since "base" */
-ulong get_timer(ulong base)
-{
- return TICKS_TO_HZ(READ_TIMER()) - base;
-}
-
-/* Delay x useconds */
-void __udelay(unsigned long usec)
-{
- ulong ini, end;
-
- ini = READ_TIMER();
- end = ini + USEC_TO_COUNT(usec);
- while ((signed)(end - READ_TIMER()) > 0)
- ;
-}
-
-unsigned long long get_ticks(void)
-{
- return get_timer(0);
-}
-
-ulong get_tbclk(void)
-{
- return CONFIG_SYS_HZ;
-}
+++ /dev/null
-if NOMADIK_NHK8815
-
-config SYS_BOARD
- default "nhk8815"
-
-config SYS_VENDOR
- default "st"
-
-config SYS_CONFIG_NAME
- default "nhk8815"
-
-endif
+++ /dev/null
-NHK8815 BOARD
-M: Nomadik Linux Team <STN_WMM_nomadik_linux@list.st.com>
-M: Alessandro Rubini <rubini@unipv.it>
-S: Maintained
-F: board/st/nhk8815/
-F: include/configs/nhk8815.h
-F: configs/nhk8815_defconfig
-F: configs/nhk8815_onenand_defconfig
+++ /dev/null
-#
-# (C) Copyright 2000-2004
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# (C) Copyright 2004
-# ARM Ltd.
-# Philippe Robin, <philippe.robin@arm.com>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := nhk8815.o
+++ /dev/null
-
-The Nomadik 8815 CPU has a "secure" boot mode where no external access
-(not even JTAG) is allowed. The "remap" bits in the evaluation board
-are configured in order to boot from the internal ROM memory (in
-secure mode).
-
-The boot process as defined by the manufacturer executes external code
-(loaded from NAND or OneNAND) that that disables such "security" in
-order to run u-boot and later the kernel without constraints. Such
-code is a proprietary initial boot loader, called "X-Loader" (in case
-anyone wonders, it has no relations with other loaders with the same
-name and there is no GPL code inside the ST X-Loader).
-
-SDRAM configuration, PLL setup and initial loading from NAND is
-implemented in the X-Loader, so U-Boot is already running in SDRAM
-when control is handed over to it.
-
-The Makefile offers two different configurations to be used if you
-boot from Nand or OneNand.
-
- make nhk8815_config
- make nhk8815_onenand_config
-
-Both support OneNand and Nand. Since U-Boot, running in RAM, can't know
-where it was loaded from, the configurations differ in where the filesystem
-is looked for by default.
-
-
-On www.st.com/nomadik and on www.stnwireless.com there are documents,
-summary data and white papers on Nomadik. The full datasheet for
-STn8815 is not currently available on line but under specific request
-to the local ST sales offices.
+++ /dev/null
-/*
- * (C) Copyright 2005
- * STMicrolelctronics, <www.st.com>
- *
- * (C) Copyright 2004
- * ARM Ltd.
- * Philippe Robin, <philippe.robin@arm.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <netdev.h>
-#include <asm/io.h>
-#include <asm/arch/gpio.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#ifdef CONFIG_SHOW_BOOT_PROGRESS
-void show_boot_progress(int progress)
-{
- printf("%i\n", progress);
-}
-#endif
-
-/*
- * Miscellaneous platform dependent initialisations
- */
-int board_init(void)
-{
- gd->bd->bi_arch_number = MACH_TYPE_NOMADIK;
- gd->bd->bi_boot_params = 0x00000100;
- writel(0xC37800F0, NOMADIK_GPIO1_BASE + 0x20);
- writel(0x00000000, NOMADIK_GPIO1_BASE + 0x24);
- writel(0x00000000, NOMADIK_GPIO1_BASE + 0x28);
- writel(readl(NOMADIK_SRC_BASE) | 0x8000, NOMADIK_SRC_BASE);
-
- /* Set up SMCS1 for Ethernet: sram-like, enabled, timing values */
- writel(0x0000305b, REG_FSMC_BCR1);
- writel(0x00033f33, REG_FSMC_BTR1);
-
- /* Set up SMCS0 for OneNand: sram-like once again */
- writel(0x000030db, NOMADIK_FSMC_BASE + 0x00); /* FSMC_BCR0 */
- writel(0x02100551, NOMADIK_FSMC_BASE + 0x04); /* FSMC_BTR0 */
-
- icache_enable();
- return 0;
-}
-
-int board_late_init(void)
-{
- /* Set the two I2C gpio lines to be gpio high */
- nmk_gpio_set(__SCL, 1); nmk_gpio_set(__SDA, 1);
- nmk_gpio_dir(__SCL, 1); nmk_gpio_dir(__SDA, 1);
- nmk_gpio_af(__SCL, GPIO_GPIO); nmk_gpio_af(__SDA, GPIO_GPIO);
-
- /* Reset the I2C port expander, on GPIO77 */
- nmk_gpio_af(77, GPIO_GPIO);
- nmk_gpio_dir(77, 1);
- nmk_gpio_set(77, 0);
- udelay(10);
- nmk_gpio_set(77, 1);
-
- return 0;
-}
-
-int dram_init(void)
-{
- gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE,
- CONFIG_SYS_SDRAM_SIZE);
- return 0;
-}
-
-void dram_init_banksize(void)
-{
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
- gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
- gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
-}
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_SMC91111
- rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
-#endif
- return rc;
-}
-#endif
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_ARCH_NOMADIK=y
-CONFIG_NOMADIK_NHK8815=y
-# CONFIG_CMD_IMLS is not set
-# CONFIG_CMD_FLASH is not set
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_SYS_PROMPT="Nomadik> "
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_ARCH_NOMADIK=y
-CONFIG_NOMADIK_NHK8815=y
-CONFIG_SYS_EXTRA_OPTIONS="BOOT_ONENAND"
-# CONFIG_CMD_IMLS is not set
-# CONFIG_CMD_FLASH is not set
-# CONFIG_CMD_SETEXPR is not set
obj-$(CONFIG_NAND_MXC) += mxc_nand.o
obj-$(CONFIG_NAND_MXS) += mxs_nand.o
obj-$(CONFIG_NAND_NDFC) += ndfc.o
-obj-$(CONFIG_NAND_NOMADIK) += nomadik.o
obj-$(CONFIG_NAND_PXA3XX) += pxa3xx_nand.o
obj-$(CONFIG_NAND_S3C2410) += s3c2410_nand.o
obj-$(CONFIG_NAND_SPEAR) += spr_nand.o
+++ /dev/null
-/*
- * (C) Copyright 2007 STMicroelectronics, <www.st.com>
- * (C) Copyright 2009 Alessandro Rubini <rubini@unipv.it>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <nand.h>
-#include <asm/io.h>
-
-static inline int parity(int b) /* b is really a byte; returns 0 or ~0 */
-{
- __asm__ __volatile__(
- "eor %0, %0, %0, lsr #4\n\t"
- "eor %0, %0, %0, lsr #2\n\t"
- "eor %0, %0, %0, lsr #1\n\t"
- "ands %0, %0, #1\n\t"
- "subne %0, %0, #2\t"
- : "=r" (b) : "0" (b));
- return b;
-}
-
-/*
- * This is the ECC routine used in hardware, according to the manual.
- * HW claims to make the calculation but not the correction; so we must
- * recalculate the bytes for a comparison.
- */
-static int ecc512(const unsigned char *data, unsigned char *ecc)
-{
- int gpar = 0;
- int i, val, par;
- int pbits = 0; /* P8, P16, ... P2048 */
- int pprime = 0; /* P8', P16', ... P2048' */
- int lowbits; /* P1, P2, P4 and primes */
-
- for (i = 0; i < 512; i++) {
- par = parity((val = data[i]));
- gpar ^= val;
- pbits ^= (i & par);
- }
- /*
- * Ok, now gpar is global parity (xor of all bytes)
- * pbits are all the parity bits (non-prime ones)
- */
- par = parity(gpar);
- pprime = pbits ^ par;
- /* Put low bits in the right position for ecc[2] (bits 7..2) */
- lowbits = 0
- | (parity(gpar & 0xf0) & 0x80) /* P4 */
- | (parity(gpar & 0x0f) & 0x40) /* P4' */
- | (parity(gpar & 0xcc) & 0x20) /* P2 */
- | (parity(gpar & 0x33) & 0x10) /* P2' */
- | (parity(gpar & 0xaa) & 0x08) /* P1 */
- | (parity(gpar & 0x55) & 0x04); /* P1' */
-
- ecc[2] = ~(lowbits | ((pbits & 0x100) >> 7) | ((pprime & 0x100) >> 8));
- /* now intermix bits for ecc[1] (P1024..P128') and ecc[0] (P64..P8') */
- ecc[1] = ~( (pbits & 0x80) >> 0 | ((pprime & 0x80) >> 1)
- | ((pbits & 0x40) >> 1) | ((pprime & 0x40) >> 2)
- | ((pbits & 0x20) >> 2) | ((pprime & 0x20) >> 3)
- | ((pbits & 0x10) >> 3) | ((pprime & 0x10) >> 4));
-
- ecc[0] = ~( (pbits & 0x8) << 4 | ((pprime & 0x8) << 3)
- | ((pbits & 0x4) << 3) | ((pprime & 0x4) << 2)
- | ((pbits & 0x2) << 2) | ((pprime & 0x2) << 1)
- | ((pbits & 0x1) << 1) | ((pprime & 0x1) << 0));
- return 0;
-}
-
-/* This is the method in the chip->ecc field */
-static int nomadik_ecc_calculate(struct mtd_info *mtd, const uint8_t *dat,
- uint8_t *ecc_code)
-{
- return ecc512(dat, ecc_code);
-}
-
-static int nomadik_ecc_correct(struct mtd_info *mtd, uint8_t *dat,
- uint8_t *r_ecc, uint8_t *c_ecc)
-{
- struct nand_chip *chip = mtd->priv;
- uint32_t r, c, d, diff; /*read, calculated, xor of them */
-
- if (!memcmp(r_ecc, c_ecc, chip->ecc.bytes))
- return 0;
-
- /* Reorder the bytes into ascending-order 24 bits -- see manual */
- r = r_ecc[2] << 22 | r_ecc[1] << 14 | r_ecc[0] << 6 | r_ecc[2] >> 2;
- c = c_ecc[2] << 22 | c_ecc[1] << 14 | c_ecc[0] << 6 | c_ecc[2] >> 2;
- diff = (r ^ c) & ((1<<24)-1); /* use 24 bits only */
-
- /* If 12 bits are different, one per pair, it's correctable */
- if (((diff | (diff>>1)) & 0x555555) == 0x555555) {
- int bit = ((diff & 2) >> 1)
- | ((diff & 0x8) >> 2) | ((diff & 0x20) >> 3);
- int byte;
-
- d = diff >> 6; /* remove bit-order info */
- byte = ((d & 2) >> 1)
- | ((d & 0x8) >> 2) | ((d & 0x20) >> 3)
- | ((d & 0x80) >> 4) | ((d & 0x200) >> 5)
- | ((d & 0x800) >> 6) | ((d & 0x2000) >> 7)
- | ((d & 0x8000) >> 8) | ((d & 0x20000) >> 9);
- /* correct the single bit */
- dat[byte] ^= 1<<bit;
- return 0;
- }
- /* If 1 bit only differs, it's one bit error in ECC, ignore */
- if ((diff ^ (1 << (ffs(diff) - 1))) == 0)
- return 0;
- /* Otherwise, uncorrectable */
- return -1;
-}
-
-static void nomadik_ecc_hwctl(struct mtd_info *mtd, int mode)
-{ /* mandatory in the structure but not used here */ }
-
-
-/* This is the layout used by older installations, we keep compatible */
-struct nand_ecclayout nomadik_ecc_layout = {
- .eccbytes = 3 * 4,
- .eccpos = { /* each subpage has 16 bytes: pos 2,3,4 hosts ECC */
- 0x02, 0x03, 0x04,
- 0x12, 0x13, 0x14,
- 0x22, 0x23, 0x24,
- 0x32, 0x33, 0x34},
- .oobfree = { {0x08, 0x08}, {0x18, 0x08}, {0x28, 0x08}, {0x38, 0x08} },
-};
-
-#define MASK_ALE (1 << 24) /* our ALE is AD21 */
-#define MASK_CLE (1 << 23) /* our CLE is AD22 */
-
-/* This is copied from the AT91SAM9 devices (Stelian Pop, Lead Tech Design) */
-static void nomadik_nand_hwcontrol(struct mtd_info *mtd,
- int cmd, unsigned int ctrl)
-{
- struct nand_chip *this = mtd->priv;
- u32 pcr0 = readl(REG_FSMC_PCR0);
-
- if (ctrl & NAND_CTRL_CHANGE) {
- ulong IO_ADDR_W = (ulong) this->IO_ADDR_W;
- IO_ADDR_W &= ~(MASK_ALE | MASK_CLE);
-
- if (ctrl & NAND_CLE)
- IO_ADDR_W |= MASK_CLE;
- if (ctrl & NAND_ALE)
- IO_ADDR_W |= MASK_ALE;
-
- if (ctrl & NAND_NCE)
- writel(pcr0 | 0x4, REG_FSMC_PCR0);
- else
- writel(pcr0 & ~0x4, REG_FSMC_PCR0);
-
- this->IO_ADDR_W = (void *) IO_ADDR_W;
- this->IO_ADDR_R = (void *) IO_ADDR_W;
- }
-
- if (cmd != NAND_CMD_NONE)
- writeb(cmd, this->IO_ADDR_W);
-}
-
-/* Returns 1 when ready; upper layers timeout at 20ms with timer routines */
-static int nomadik_nand_ready(struct mtd_info *mtd)
-{
- return 1; /* The ready bit is handled in hardware */
-}
-
-/* Copy a buffer 32bits at a time: faster than defualt method which is 8bit */
-static void nomadik_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
-{
- int i;
- struct nand_chip *chip = mtd->priv;
- u32 *p = (u32 *) buf;
-
- len >>= 2;
- writel(0, REG_FSMC_ECCR0);
- for (i = 0; i < len; i++)
- p[i] = readl(chip->IO_ADDR_R);
-}
-
-int board_nand_init(struct nand_chip *chip)
-{
- /* Set up the FSMC_PCR0 for nand access*/
- writel(0x0000004a, REG_FSMC_PCR0);
- /* Set up FSMC_PMEM0, FSMC_PATT0 with timing data for access */
- writel(0x00020401, REG_FSMC_PMEM0);
- writel(0x00020404, REG_FSMC_PATT0);
-
- chip->options = NAND_COPYBACK | NAND_CACHEPRG | NAND_NO_PADDING;
- chip->cmd_ctrl = nomadik_nand_hwcontrol;
- chip->dev_ready = nomadik_nand_ready;
- /* The chip allows 32bit reads, so avoid the default 8bit copy */
- chip->read_buf = nomadik_nand_read_buf;
-
- /* ECC: follow the hardware-defined rulse, but do it in sw */
- chip->ecc.mode = NAND_ECC_HW;
- chip->ecc.bytes = 3;
- chip->ecc.size = 512;
- chip->ecc.strength = 1;
- chip->ecc.layout = &nomadik_ecc_layout;
- chip->ecc.calculate = nomadik_ecc_calculate;
- chip->ecc.hwctl = nomadik_ecc_hwctl;
- chip->ecc.correct = nomadik_ecc_correct;
-
- return 0;
-}
+++ /dev/null
-/*
- * (C) Copyright 2005
- * STMicroelectronics.
- * Configuration settings for the "Nomadik Hardware Kit" NHK-8815,
- * the evaluation board for the Nomadik 8815 System on Chip.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <nomadik.h>
-
-#define CONFIG_NOMADIK_8815 /* cpu variant */
-
-#define CONFIG_SKIP_LOWLEVEL_INIT /* we have already been loaded to RAM */
-
-/* commands */
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
-#define CONFIG_SYS_NO_FLASH
-/* There is NAND storage */
-#define CONFIG_NAND_NOMADIK
-#define CONFIG_CMD_JFFS2
-
-/* user interface */
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
- + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Arg Buffer Size */
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_SYS_LOAD_ADDR 0x800000 /* default load address */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE
-
-/* boot config */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_BOOTDELAY 1
-#define CONFIG_BOOTARGS "root=/dev/ram0 console=ttyAMA1,115200n8 init=linuxrc"
-#define CONFIG_BOOTCOMMAND "fsload 0x100000 kernel.uimg;" \
- " fsload 0x800000 initrd.gz.uimg;" \
- " bootm 0x100000 0x800000"
-
-/* memory-related information */
-#define CONFIG_NR_DRAM_BANKS 2
-#define PHYS_SDRAM_1 0x00000000 /* DDR-SDRAM Bank #1 */
-#define PHYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */
-#define PHYS_SDRAM_2 0x08000000 /* SDR-SDRAM BANK #2*/
-#define PHYS_SDRAM_2_SIZE 0x04000000 /* 64 MB */
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_SDRAM_SIZE (PHYS_SDRAM_1_SIZE + PHYS_SDRAM_2_SIZE)
-/* The IPL loads us at 0, tell so to u-boot. Put stack pointer 1M into RAM */
-#define CONFIG_SYS_TEXT_BASE 0x00000000
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE + (1<<20))
-
-#define CONFIG_SYS_MEMTEST_START 0x00000000
-#define CONFIG_SYS_MEMTEST_END 0x0FFFFFFF
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 256 * 1024)
-
-#define CONFIG_BOARD_LATE_INIT /* call board_late_init during start up */
-
-/* timing informazion */
-#define CONFIG_SYS_TIMERBASE 0x101E2000
-
-/* serial port (PL011) configuration */
-#define CONFIG_PL011_SERIAL
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
-#define CFG_SERIAL0 0x101FD000
-#define CFG_SERIAL1 0x101FB000
-
-#define CONFIG_PL01x_PORTS { (void *)CFG_SERIAL0, (void *)CFG_SERIAL1 }
-#define CONFIG_PL011_CLOCK 48000000
-
-/* i2c, for the port extenders (uses gpio.c in board directory) */
-#ifndef __ASSEMBLY__
-#include <asm/arch/gpio.h>
-#define CONFIG_CMD_I2C
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT 1 /* I2C bit-banged */
-#define I2C_SOFT_DEFS
-#define CONFIG_SYS_I2C_SOFT_SPEED 400000
-#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F
-#define __SDA 63
-#define __SCL 62
-#define I2C_SDA(x) nmk_gpio_set(__SDA, x)
-#define I2C_SCL(x) nmk_gpio_set(__SCL, x)
-#define I2C_READ (nmk_gpio_get(__SDA)!=0)
-#define I2C_ACTIVE nmk_gpio_dir(__SDA, 1)
-#define I2C_TRISTATE nmk_gpio_dir(__SDA, 0)
-#define I2C_DELAY (udelay(2))
-#endif /* __ASSEMBLY__ */
-
-/* Ethernet */
-#define PCI_MEMORY_VADDR 0xe8000000
-#define PCI_IO_VADDR 0xee000000
-#define __io(a) ((void __iomem *)(PCI_IO_VADDR + (a)))
-#define __mem_isa(a) ((a) + PCI_MEMORY_VADDR)
-
-#define CONFIG_SMC91111 /* Using SMC91c111*/
-#define CONFIG_SMC91111_BASE 0x34000300
-#undef CONFIG_SMC91111_EXT_PHY /* Internal PHY */
-#define CONFIG_SMC_USE_32_BIT
-#define CONFIG_BOOTFILE "uImage"
-
-#define CONFIG_IP_DEFRAG /* Allows faster download, TFTP and NFS */
-#define CONFIG_TFTP_BLOCKSIZE 4096
-#define CONFIG_NFS_READ_SIZE 4096
-
-/* Storage information: onenand and nand */
-#define CONFIG_CMD_ONENAND
-#define CONFIG_MTD_ONENAND_VERIFY_WRITE
-#define CONFIG_SYS_ONENAND_BASE 0x30000000
-
-#define CONFIG_CMD_NAND
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE 0x40000000 /* SMPS0n */
-
-/*
- * Filesystem information
- *
- * Since U-Boot has been loaded to RAM by vendor code, we could use
- * either or both OneNand and Nand. However, we need to know where the
- * filesystem lives. Comments below report vendor-selected partitions
- */
-#ifdef CONFIG_BOOT_ONENAND
- /* Partition Size Start
- * XloaderTOC + X-Loader 256KB 0x00000000
- * Memory init function 256KB 0x00040000
- * U-Boot + env 2MB 0x00080000
- * Sysimage (kernel + ramdisk) 4MB 0x00280000
- * JFFS2 Root filesystem 22MB 0x00680000
- * JFFS2 User Data 227.5MB 0x01C80000
- */
-# define CONFIG_JFFS2_DEV "onenand0"
-# define CONFIG_JFFS2_PART_SIZE 0x01600000
-# define CONFIG_JFFS2_PART_OFFSET 0x00680000
-# define CONFIG_ENV_IS_IN_ONENAND
-# define CONFIG_ENV_SIZE 0x20000 /* 128 Kb - one sector */
-# define CONFIG_ENV_ADDR (0x00280000 - CONFIG_ENV_SIZE)
-
-#else /* BOOT_NAND */
- /* Partition Size Start
- * XloaderTOC + X-Loader 256KB 0x00000000
- * Memory init function 256KB 0x00040000
- * U-Boot + env 2MB 0x00080000
- * Kernel Image 3MB 0x00280000
- * JFFS2 Root filesystem 22MB 0x00580000
- * JFFS2 User Data 100.5MB 0x01b80000
- */
-# define CONFIG_JFFS2_DEV "nand0"
-# define CONFIG_JFFS2_NAND 1 /* For the jffs2 support*/
-# define CONFIG_JFFS2_PART_SIZE 0x01600000
-# define CONFIG_JFFS2_PART_OFFSET 0x00580000
-# define CONFIG_ENV_IS_IN_NAND
-# define CONFIG_ENV_SIZE 0x20000 /* 128 Kb - one sector */
-# define CONFIG_ENV_OFFSET (0x00280000 - CONFIG_ENV_SIZE)
-
-#endif /* CONFIG_BOOT_ONENAND */
-
-/* this is needed to make hello_world.c and other stuff happy */
-#define CONFIG_SYS_MAX_FLASH_SECT 512
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
-
-#endif /* __CONFIG_H */
+++ /dev/null
-/* Collection of constants used to access Nomadik registers */
-
-#ifndef __NOMADIK_H__
-#define __NOMADIK_H__
-
-/* Base addresses of our peripherals */
-#define NOMADIK_CLCDC_BASE 0x10120000 /* CLCD Controller */
-#define NOMADIK_SRC_BASE 0x101E0000 /* System and Reset Cnt */
-#define NOMADIK_PMU_BASE 0x101E9000 /* Power Management Unit */
-#define NOMADIK_MPMC_BASE 0x10110000 /* SDRAM Controller */
-#define NOMADIK_FSMC_BASE 0x10100000 /* FSMC Controller */
-#define NOMADIK_1NAND_BASE 0x30000000
-#define NOMADIK_GPIO0_BASE 0x101E4000
-#define NOMADIK_GPIO1_BASE 0x101E5000
-#define NOMADIK_GPIO2_BASE 0x101E6000
-#define NOMADIK_GPIO3_BASE 0x101E7000
-#define NOMADIK_CPLD_BASE 0x36000000
-#define NOMADIK_UART0_BASE 0x101FD000
-#define NOMADIK_UART1_BASE 0x101FB000
-#define NOMADIK_UART2_BASE 0x101F2000
-
-#define NOMADIK_I2C1_BASE 0x101F7000 /* I2C1 interface */
-#define NOMADIK_I2C0_BASE 0x101F8000 /* I2C0 interface */
-
-#define NOMADIK_RTC_BASE 0x101E8000
-#define NOMADIK_ETH0_BASE 0x36800300
-#define NOMADIK_CPLD_UART_BASE 0x36480000
-
-/* Chip select registers ("Flexible Static Memory Controller") */
-
-#define REG_FSMC_BCR0 (NOMADIK_FSMC_BASE + 0x00)
-#define REG_FSMC_BTR0 (NOMADIK_FSMC_BASE + 0x04)
-#define REG_FSMC_BCR1 (NOMADIK_FSMC_BASE + 0x08)
-#define REG_FSMC_BTR1 (NOMADIK_FSMC_BASE + 0x0c)
-#define REG_FSMC_PCR0 (NOMADIK_FSMC_BASE + 0x40)
-#define REG_FSMC_PMEM0 (NOMADIK_FSMC_BASE + 0x48)
-#define REG_FSMC_PATT0 (NOMADIK_FSMC_BASE + 0x4c)
-#define REG_FSMC_ECCR0 (NOMADIK_FSMC_BASE + 0x54)
-
-#endif /* __NOMADIK_H__ */
projects / project / bcm63xx / u-boot.git / commitdiff