realtek: Update rtl839x.dtsi for realtek,rtl-intc, new gpio controller remove RTL8231...

Update the IRQ configuration to work with the new rtl-intc controller.
Also change all KSEG1 addresses in reg = <> of the devics to physical
addresses.

Use the new gpio-otto controller instead of the legacy driver.
Also remove the memory node as this is better put into a device .dts.

Also remove the RTL8231 GPIO controller node from this base file
since the chip might not be found in all Realtek RTL839x devices.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>

diff --git a/target/linux/realtek/dts-5.10/rtl839x.dtsi b/target/linux/realtek/dts-5.10/rtl839x.dtsi
new file mode 100644 (file)
index 0000000..19da1c1
--- /dev/null
+++ b/target/linux/realtek/dts-5.10/rtl839x.dtsi
@@ -0,0 +1,225 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#define STRINGIZE(s) #s
+#define LAN_LABEL(p, s) STRINGIZE(p ## s)
+#define SWITCH_PORT_LABEL(n) LAN_LABEL(lan, n)
+
+#define INTERNAL_PHY(n) \
+       phy##n: ethernet-phy@##n { \
+               reg = <##n>; \
+               compatible = "ethernet-phy-ieee802.3-c22"; \
+               phy-is-integrated; \
+       };
+
+#define EXTERNAL_PHY(n) \
+       phy##n: ethernet-phy@##n { \
+               reg = <##n>; \
+               compatible = "ethernet-phy-ieee802.3-c22"; \
+       };
+
+#define EXTERNAL_SFP_PHY(n) \
+       phy##n: ethernet-phy@##n { \
+               compatible = "ethernet-phy-ieee802.3-c22"; \
+               sfp; \
+               media = "fibre"; \
+               reg = <##n>; \
+       };
+
+#define SWITCH_PORT(n, s, m) \
+       port@##n { \
+               reg = <##n>; \
+               label = SWITCH_PORT_LABEL(s) ; \
+               phy-handle = <&phy##n>; \
+               phy-mode = #m ; \
+       };
+
+#define SWITCH_SFP_PORT(n, s, m) \
+       port@##n { \
+               reg = <##n>; \
+               label = SWITCH_PORT_LABEL(s) ; \
+               phy-handle = <&phy##n>; \
+               phy-mode = #m ; \
+               fixed-link { \
+                       speed = <1000>; \
+                       full-duplex; \
+               }; \
+       };
+
+/ {
+       #address-cells = <1>;
+       #size-cells = <1>;
+
+       compatible = "realtek,rtl839x-soc";
+
+       cpus {
+               #address-cells = <1>;
+               #size-cells = <0>;
+               frequency = <700000000>;
+
+               cpu@0 {
+                       compatible = "mips,mips34Kc";
+                       reg = <0>;
+               };
+       };
+
+       chosen {
+               bootargs = "console=ttyS0,38400";
+       };
+
+       lx_clk: lx_clk {
+               compatible = "fixed-clock";
+               #clock-cells = <0>;
+               clock-frequency = <200000000>;
+       };
+
+       cpuintc: cpuintc {
+               compatible = "mti,cpu-interrupt-controller";
+               #address-cells = <0>;
+               #interrupt-cells = <1>;
+               interrupt-controller;
+       };
+
+       soc: soc {
+               compatible = "simple-bus";
+               #address-cells = <1>;
+               #size-cells = <1>;
+               ranges = <0x0 0x18000000 0x10000>;
+
+               intc: interrupt-controller@3000 {
+                       compatible = "realtek,rtl8390-intc", "realtek,rtl-intc";
+                       reg = <0x3000 0x18>, <0x3018 0x18>;
+                       interrupt-controller;
+                       #interrupt-cells = <2>;
+
+                       interrupt-parent = <&cpuintc>;
+                       interrupts = <2>, <3>, <4>, <5>, <6>;
+               };
+
+               spi0: spi@1200 {
+                       compatible = "realtek,rtl8380-spi";
+                       reg = <0x1200 0x100>;
+
+                       #address-cells = <1>;
+                       #size-cells = <0>;
+               };
+
+               uart0: uart@2000 {
+                       compatible = "ns16550a";
+                       reg = <0x2000 0x100>;
+
+                       clocks = <&lx_clk>;
+
+                       interrupt-parent = <&intc>;
+                       interrupts = <31 1>;
+
+                       reg-io-width = <1>;
+                       reg-shift = <2>;
+                       fifo-size = <1>;
+                       no-loopback-test;
+               };
+
+               uart1: uart@2100 {
+                       pinctrl-names = "default";
+                       pinctrl-0 = <&enable_uart1>;
+
+                       compatible = "ns16550a";
+                       reg = <0x2100 0x100>;
+
+                       clocks = <&lx_clk>;
+
+                       interrupt-parent = <&intc>;
+                       interrupts = <30 2>;
+
+                       reg-io-width = <1>;
+                       reg-shift = <2>;
+                       fifo-size = <1>;
+                       no-loopback-test;
+
+                       status = "disabled";
+               };
+
+               gpio0: gpio-controller@b3500 {
+                       compatible = "realtek,rtl8390-gpio", "realtek,otto-gpio";
+                       reg = <0x3500 0x20>;
+
+                       gpio-controller;
+                       #gpio-cells = <2>;
+                       ngpios = <24>;
+
+                       interrupt-controller;
+                       #interrupt-cells = <2>;
+                       interrupt-parent = <&intc>;
+                       interrupts = <23 2>;
+               };
+
+               watchdog0: watchdog@3150 {
+                       compatible = "realtek,rtl8390-wdt";
+                       reg = <0x3150 0xc>;
+
+                       realtek,reset-mode = "soc";
+
+                       clocks = <&lx_clk>;
+                       timeout-sec = <30>;
+
+                       interrupt-parent = <&intc>;
+                       interrupt-names = "phase1", "phase2";
+                       interrupts = <19 4>, <18 4>;
+               };
+
+       };
+
+       pinmux: pinmux@1b001000 {
+               compatible = "pinctrl-single";
+               reg = <0x1b000004 0x4>;
+
+               pinctrl-single,bit-per-mux;
+               pinctrl-single,register-width = <32>;
+               pinctrl-single,function-mask = <0x1>;
+               #pinctrl-cells = <2>;
+
+               enable_uart1: pinmux_enable_uart1 {
+                       pinctrl-single,bits = <0x0 0x1 0x3>;
+               };
+       };
+
+       /* LED_GLB_CTRL */
+       pinmux_led: pinmux@1b00a000 {
+               compatible = "pinctrl-single";
+               reg = <0x1b0000e4 0x4>;
+
+               pinctrl-single,bit-per-mux;
+               pinctrl-single,register-width = <32>;
+               pinctrl-single,function-mask = <0x1>;
+               #pinctrl-cells = <2>;
+
+               /* enable GPIO 0 */
+               pinmux_disable_sys_led: disable_sys_led {
+                       pinctrl-single,bits = <0x0 0x0 0x4000>;
+               };
+       };
+
+       ethernet0: ethernet@1b00a300 {
+               compatible = "realtek,rtl838x-eth";
+               reg = <0x1b00a300 0x100>;
+
+               interrupt-parent = <&intc>;
+               interrupts = <24 3>;
+
+               phy-mode = "internal";
+
+               fixed-link {
+                       speed = <1000>;
+                       full-duplex;
+               };
+       };
+
+       switch0: switch@1b000000 {
+               status = "okay";
+               compatible = "realtek,rtl83xx-switch";
+
+               interrupt-parent = <&intc>;
+               interrupts = <20 2>;
+       };
+};