Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi (11n)
* 3T3R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 1x ethernet
- AR8035 ethernet PHY (RGMII)
- 10/100/1000 Mbps Ethernet
- 802.3af POE
- used as LAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot
0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[rebase, add LED migration]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
PKG_NAME:=uboot-envtools
PKG_DISTNAME:=u-boot
PKG_VERSION:=2020.04
-PKG_RELEASE:=19
+PKG_RELEASE:=20
PKG_SOURCE:=$(PKG_DISTNAME)-$(PKG_VERSION).tar.bz2
PKG_SOURCE_URL:= \
openmesh,mr900-v1|\
openmesh,mr900-v2|\
openmesh,mr1750-v1|\
+openmesh,mr1750-v2|\
openmesh,om5p|\
openmesh,om5p-ac-v2|\
samsung,wam250|\
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca9558_openmesh_mr.dtsi"
+
+/ {
+ compatible = "openmesh,mr1750-v2", "qca,qca9558";
+ model = "OpenMesh MR1750 v2";
+};
+
+&led_wifi2g {
+ linux,default-trigger = "phy1tpt";
+};
+
+&led_wifi5g {
+ linux,default-trigger = "phy0tpt";
+};
enterasys,ws-ap3705i|\
openmesh,mr900-v1|\
openmesh,mr900-v2|\
-openmesh,mr1750-v1)
+openmesh,mr1750-v1|\
+openmesh,mr1750-v2)
ucidef_set_led_netdev "lan" "LAN" "blue:lan" "eth0"
;;
compex,wpj344-16m|\
openmesh,mr900-v1|\
openmesh,mr900-v2|\
openmesh,mr1750-v1|\
+ openmesh,mr1750-v2|\
pcs,cap324|\
pisen,ts-d084|\
pisen,wmb001n|\
caldata_extract "art" 0x5000 0x844
ath10k_patch_mac $(mtd_get_mac_binary art 0xc)
;;
- openmesh,mr1750-v1)
+ openmesh,mr1750-v1|\
+ openmesh,mr1750-v2)
caldata_extract "ART" 0x5000 0x844
ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
;;
;;
openmesh,mr900-v1|\
openmesh,mr900-v2|\
-openmesh,mr1750-v1)
+openmesh,mr1750-v1|\
+openmesh,mr1750-v2)
migrate_leds ":wlan24=:wifi2g" ":wlan58=:wifi5g" ":wan=:lan"
;;
pcs,cap324)
openmesh,mr900-v1|\
openmesh,mr900-v2|\
openmesh,mr1750-v1|\
+ openmesh,mr1750-v2|\
openmesh,om2p-v2|\
openmesh,om2p-v4|\
openmesh,om2p-hs-v1|\
endef
TARGET_DEVICES += openmesh_mr1750-v1
+define Device/openmesh_mr1750-v2
+ $(Device/openmesh_common_64k)
+ SOC := qca9558
+ DEVICE_MODEL := MR1750
+ DEVICE_VARIANT := v2
+ DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
+ OPENMESH_CE_TYPE := MR1750
+ SUPPORTED_DEVICES += mr1750v2
+endef
+TARGET_DEVICES += openmesh_mr1750-v2
+
define Device/openmesh_om2p-v2
$(Device/openmesh_common_256k)
SOC := ar9330