.resource = au1200_psc0_res,
};
+static struct resource au1200_psc1_res[] = {
+ [0] = {
+ .start = PSC1_PHYS_ADDR,
+ .end = PSC1_PHYS_ADDR + 0x000fffff,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = AU1200_PSC1_INT,
+ .end = AU1200_PSC1_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+ [2] = {
+ .start = DSCR_CMD0_PSC1_TX,
+ .end = DSCR_CMD0_PSC1_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ [3] = {
+ .start = DSCR_CMD0_PSC1_RX,
+ .end = DSCR_CMD0_PSC1_RX,
+ .flags = IORESOURCE_DMA,
+ },
+};
+
+static struct platform_device db1200_audio_dev = {
+ /* name assigned later based on switch setting */
+ .id = 1, /* PSC ID */
+ .num_resources = ARRAY_SIZE(au1200_psc1_res),
+ .resource = au1200_psc1_res,
+};
+
static struct platform_device *db1200_devs[] __initdata = {
NULL, /* PSC0, selected by S6.8 */
&db1200_ide_dev,
&db1200_eth_dev,
&db1200_rtc_dev,
&db1200_nand_dev,
+ &db1200_audio_dev,
};
static int __init db1200_dev_init(void)
ARRAY_SIZE(db1200_i2c_devs));
/* SWITCHES: S6.8 I2C/SPI selector (OFF=I2C ON=SPI)
+ * S6.7 AC97/I2S selector (OFF=AC97 ON=I2S)
*/
/* NOTE: GPIO215 controls OTG VBUS supply. In SPI mode however
__raw_writel(pfc, (void __iomem *)SYS_PINFUNC);
wmb();
+ /* Audio: DIP7 selects I2S(0)/AC97(1), but need I2C for I2S!
+ * so: DIP7=1 || DIP8=0 => AC97, DIP7=0 && DIP8=1 => I2S
+ */
+ sw &= BCSR_SWITCHES_DIP_8 | BCSR_SWITCHES_DIP_7;
+ if (sw == BCSR_SWITCHES_DIP_8) {
+ bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_PSC1MUX);
+ db1200_audio_dev.name = "au1xpsc_i2s";
+ printk(KERN_INFO " S6.7 ON : PSC1 mode I2S\n");
+ } else {
+ bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC1MUX, 0);
+ db1200_audio_dev.name = "au1xpsc_ac97";
+ printk(KERN_INFO " S6.7 OFF: PSC1 mode AC97\n");
+ }
+
+ /* Audio PSC clock is supplied externally. (FIXME: platdata!!) */
+ __raw_writel(PSC_SEL_CLK_SERCLK,
+ (void __iomem *)KSEG1ADDR(PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
+ wmb();
+
db1x_register_pcmcia_socket(PCMCIA_ATTR_PSEUDO_PHYS,
PCMCIA_ATTR_PSEUDO_PHYS + 0x00040000 - 1,
PCMCIA_MEM_PSEUDO_PHYS,
##
## Boards
##
-config SND_SOC_SAMPLE_PSC_AC97
- tristate "Sample Au12x0/Au1550 PSC AC97 sound machine"
+config SND_SOC_DB1200
+ tristate "DB1200 AC97+I2S audio support"
depends on SND_SOC_AU1XPSC
select SND_SOC_AU1XPSC_AC97
select SND_SOC_AC97_CODEC
+ select SND_SOC_AU1XPSC_I2S
+ select SND_SOC_WM8731
help
- This is a sample AC97 sound machine for use in Au12x0/Au1550
- based systems which have audio on PSC1 (e.g. Db1200 demoboard).
+ Select this option to enable audio (AC97 or I2S) on the
+ Alchemy/AMD/RMI DB1200 demoboard.
obj-$(CONFIG_SND_SOC_AU1XPSC_AC97) += snd-soc-au1xpsc-ac97.o
# Boards
-snd-soc-sample-ac97-objs := sample-ac97.o
+snd-soc-db1200-objs := db1200.o
-obj-$(CONFIG_SND_SOC_SAMPLE_PSC_AC97) += snd-soc-sample-ac97.o
+obj-$(CONFIG_SND_SOC_DB1200) += snd-soc-db1200.o
--- /dev/null
+/*
+ * DB1200 ASoC audio fabric support code.
+ *
+ * (c) 2008-9 Manuel Lauss <manuel.lauss@gmail.com>
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/timer.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <sound/core.h>
+#include <sound/pcm.h>
+#include <sound/soc.h>
+#include <sound/soc-dapm.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1xxx_psc.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-db1x00/bcsr.h>
+
+#include "../codecs/ac97.h"
+#include "../codecs/wm8731.h"
+#include "psc.h"
+
+/*------------------------- AC97 PART ---------------------------*/
+
+static struct snd_soc_dai_link db1200_ac97_dai = {
+ .name = "AC97",
+ .stream_name = "AC97 HiFi",
+ .cpu_dai = &au1xpsc_ac97_dai,
+ .codec_dai = &ac97_dai,
+};
+
+static struct snd_soc_card db1200_ac97_machine = {
+ .name = "DB1200_AC97",
+ .dai_link = &db1200_ac97_dai,
+ .num_links = 1,
+ .platform = &au1xpsc_soc_platform,
+};
+
+static struct snd_soc_device db1200_ac97_devdata = {
+ .card = &db1200_ac97_machine,
+ .codec_dev = &soc_codec_dev_ac97,
+};
+
+/*------------------------- I2S PART ---------------------------*/
+
+static int db1200_i2s_startup(struct snd_pcm_substream *substream)
+{
+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
+ struct snd_soc_dai *codec_dai = rtd->dai->codec_dai;
+ struct snd_soc_dai *cpu_dai = rtd->dai->cpu_dai;
+ int ret;
+
+ /* WM8731 has its own 12MHz crystal */
+ snd_soc_dai_set_sysclk(codec_dai, WM8731_SYSCLK,
+ 12000000, SND_SOC_CLOCK_IN);
+
+ /* codec is bitclock and lrclk master */
+ ret = snd_soc_dai_set_fmt(codec_dai, SND_SOC_DAIFMT_LEFT_J |
+ SND_SOC_DAIFMT_NB_NF | SND_SOC_DAIFMT_CBM_CFM);
+ if (ret < 0)
+ goto out;
+
+ ret = snd_soc_dai_set_fmt(cpu_dai, SND_SOC_DAIFMT_LEFT_J |
+ SND_SOC_DAIFMT_NB_NF | SND_SOC_DAIFMT_CBM_CFM);
+ if (ret < 0)
+ goto out;
+
+ ret = 0;
+out:
+ return ret;
+}
+
+static struct snd_soc_ops db1200_i2s_wm8731_ops = {
+ .startup = db1200_i2s_startup,
+};
+
+static struct snd_soc_dai_link db1200_i2s_dai = {
+ .name = "WM8731",
+ .stream_name = "WM8731 PCM",
+ .cpu_dai = &au1xpsc_i2s_dai,
+ .codec_dai = &wm8731_dai,
+ .ops = &db1200_i2s_wm8731_ops,
+};
+
+static struct snd_soc_card db1200_i2s_machine = {
+ .name = "DB1200_I2S",
+ .dai_link = &db1200_i2s_dai,
+ .num_links = 1,
+ .platform = &au1xpsc_soc_platform,
+};
+
+static struct snd_soc_device db1200_i2s_devdata = {
+ .card = &db1200_i2s_machine,
+ .codec_dev = &soc_codec_dev_wm8731,
+};
+
+/*------------------------- COMMON PART ---------------------------*/
+
+static struct platform_device *db1200_asoc_dev;
+
+static int __init db1200_audio_load(void)
+{
+ int ret;
+
+ ret = -ENOMEM;
+ db1200_asoc_dev = platform_device_alloc("soc-audio", -1);
+ if (!db1200_asoc_dev)
+ goto out;
+
+ /* DB1200 board setup set PSC1MUX to preferred audio device */
+ if (bcsr_read(BCSR_RESETS) & BCSR_RESETS_PSC1MUX)
+ platform_set_drvdata(db1200_asoc_dev, &db1200_i2s_devdata);
+ else
+ platform_set_drvdata(db1200_asoc_dev, &db1200_ac97_devdata);
+
+ db1200_ac97_devdata.dev = &db1200_asoc_dev->dev;
+ db1200_i2s_devdata.dev = &db1200_asoc_dev->dev;
+ ret = platform_device_add(db1200_asoc_dev);
+
+ if (ret) {
+ platform_device_put(db1200_asoc_dev);
+ db1200_asoc_dev = NULL;
+ }
+out:
+ return ret;
+}
+
+static void __exit db1200_audio_unload(void)
+{
+ platform_device_unregister(db1200_asoc_dev);
+}
+
+module_init(db1200_audio_load);
+module_exit(db1200_audio_unload);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("DB1200 ASoC audio support");
+MODULE_AUTHOR("Manuel Lauss");
+++ /dev/null
-/*
- * Sample Au12x0/Au1550 PSC AC97 sound machine.
- *
- * Copyright (c) 2007-2008 Manuel Lauss <mano@roarinelk.homelinux.net>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms outlined in the file COPYING at the root of this
- * source archive.
- *
- * This is a very generic AC97 sound machine driver for boards which
- * have (AC97) audio at PSC1 (e.g. DB1200 demoboards).
- */
-
-#include <linux/module.h>
-#include <linux/moduleparam.h>
-#include <linux/timer.h>
-#include <linux/interrupt.h>
-#include <linux/platform_device.h>
-#include <sound/core.h>
-#include <sound/pcm.h>
-#include <sound/soc.h>
-#include <sound/soc-dapm.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-au1x00/au1xxx_psc.h>
-#include <asm/mach-au1x00/au1xxx_dbdma.h>
-
-#include "../codecs/ac97.h"
-#include "psc.h"
-
-static int au1xpsc_sample_ac97_init(struct snd_soc_codec *codec)
-{
- snd_soc_dapm_sync(codec);
- return 0;
-}
-
-static struct snd_soc_dai_link au1xpsc_sample_ac97_dai = {
- .name = "AC97",
- .stream_name = "AC97 HiFi",
- .cpu_dai = &au1xpsc_ac97_dai, /* see psc-ac97.c */
- .codec_dai = &ac97_dai, /* see codecs/ac97.c */
- .init = au1xpsc_sample_ac97_init,
- .ops = NULL,
-};
-
-static struct snd_soc_card au1xpsc_sample_ac97_machine = {
- .name = "Au1xxx PSC AC97 Audio",
- .dai_link = &au1xpsc_sample_ac97_dai,
- .num_links = 1,
-};
-
-static struct snd_soc_device au1xpsc_sample_ac97_devdata = {
- .card = &au1xpsc_sample_ac97_machine,
- .platform = &au1xpsc_soc_platform, /* see dbdma2.c */
- .codec_dev = &soc_codec_dev_ac97,
-};
-
-static struct resource au1xpsc_psc1_res[] = {
- [0] = {
- .start = CPHYSADDR(PSC1_BASE_ADDR),
- .end = CPHYSADDR(PSC1_BASE_ADDR) + 0x000fffff,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
-#ifdef CONFIG_SOC_AU1200
- .start = AU1200_PSC1_INT,
- .end = AU1200_PSC1_INT,
-#elif defined(CONFIG_SOC_AU1550)
- .start = AU1550_PSC1_INT,
- .end = AU1550_PSC1_INT,
-#endif
- .flags = IORESOURCE_IRQ,
- },
- [2] = {
- .start = DSCR_CMD0_PSC1_TX,
- .end = DSCR_CMD0_PSC1_TX,
- .flags = IORESOURCE_DMA,
- },
- [3] = {
- .start = DSCR_CMD0_PSC1_RX,
- .end = DSCR_CMD0_PSC1_RX,
- .flags = IORESOURCE_DMA,
- },
-};
-
-static struct platform_device *au1xpsc_sample_ac97_dev;
-
-static int __init au1xpsc_sample_ac97_load(void)
-{
- int ret;
-
-#ifdef CONFIG_SOC_AU1200
- unsigned long io;
-
- /* modify sys_pinfunc for AC97 on PSC1 */
- io = au_readl(SYS_PINFUNC);
- io |= SYS_PINFUNC_P1C;
- io &= ~(SYS_PINFUNC_P1A | SYS_PINFUNC_P1B);
- au_writel(io, SYS_PINFUNC);
- au_sync();
-#endif
-
- ret = -ENOMEM;
-
- /* setup PSC clock source for AC97 part: external clock provided
- * by codec. The psc-ac97.c driver depends on this setting!
- */
- au_writel(PSC_SEL_CLK_SERCLK, PSC1_BASE_ADDR + PSC_SEL_OFFSET);
- au_sync();
-
- au1xpsc_sample_ac97_dev = platform_device_alloc("soc-audio", -1);
- if (!au1xpsc_sample_ac97_dev)
- goto out;
-
- au1xpsc_sample_ac97_dev->resource =
- kmemdup(au1xpsc_psc1_res, sizeof(struct resource) *
- ARRAY_SIZE(au1xpsc_psc1_res), GFP_KERNEL);
- au1xpsc_sample_ac97_dev->num_resources = ARRAY_SIZE(au1xpsc_psc1_res);
- au1xpsc_sample_ac97_dev->id = 1;
-
- platform_set_drvdata(au1xpsc_sample_ac97_dev,
- &au1xpsc_sample_ac97_devdata);
- au1xpsc_sample_ac97_devdata.dev = &au1xpsc_sample_ac97_dev->dev;
- ret = platform_device_add(au1xpsc_sample_ac97_dev);
-
- if (ret) {
- platform_device_put(au1xpsc_sample_ac97_dev);
- au1xpsc_sample_ac97_dev = NULL;
- }
-
-out:
- return ret;
-}
-
-static void __exit au1xpsc_sample_ac97_exit(void)
-{
- platform_device_unregister(au1xpsc_sample_ac97_dev);
-}
-
-module_init(au1xpsc_sample_ac97_load);
-module_exit(au1xpsc_sample_ac97_exit);
-
-MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("Au1xxx PSC sample AC97 machine");
-MODULE_AUTHOR("Manuel Lauss <mano@roarinelk.homelinux.net>");
projects / openwrt / staging / blogic.git / commitdiff