ath79: add support for NEC Aterm WR9500N

ath79: add support for NEC Aterm WR9500N

NEC Aterm WR9500N is a 2.4/5 GHz band 11n (Wi-Fi 4) router, based on
AR9344.

Specification:

- SoC             : Atheros AR9344
- RAM             : DDR2 128 MiB (2x Nanya NT5TU32M16DG-AC)
- Flash           : SPI-NOR 16 MiB (Macronix MX25L12845EMI-10G)
- WLAN            : 2.4/5 GHz
  - 2.4 GHz       : 2T2R, Atheros AR9344 (SoC)
  - 5 GHz         : 3T3R, Atheros AR9380
- Ethernet        : 5x 10/100/1000 Mbps
  - switch        : Atheros AR8327
- LEDs/Keys (GPIO): 12x/4x
  - note          : all LEDs are controlled by ath9k chip (AR9380)
- UART            : pad on PCB (near shielded ath9k chip, white circle)
  - assignment    : 3.3V, GND, TX, RX from AR8327 side
  - settings      : 9600n8
- USB             : 1x USB 2.0 Type-A
  - hub (internal): NEC uPD720114
- Power           : 12 VDC, 1.5 A (Max. 17 W)
- Stock OS        : NetBSD based

Flash instruction using initramfs-factory.bin image (StockFW WebUI):

1. Boot WR9500N with router mode normally
2. Access to the WebUI ("http://aterm.me/" or "http://192.168.0.1/") on
   the device and open firmware update page ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory.bin image and click update
   ("更新") button
4. After updating, the device will be rebooted and booted with OpenWrt
   initramfs image
5. On the initramfs image, upload (or download) uboot.bin and
   sysupgrade.bin image to the device
6. Replace the bootloader with a uboot.bin image

   mtd write <uboot.bin image> bootloader

7. Perform sysupgrade with a sysupgrade.bin image

   sysupgrade <sysupgrade image>

8. Wait ~120 seconds to complete flashing

Flash instruction using initramfs-factory.bin image (bootloader CLI):

 1. Connect and open serial console
 2. Power on WR9500N and interrupt bootloader by ESC key
 3. Login to the bootloader CLI with a password "chiron"
 4. Start TFTP server by "tftpd" command
 5. Upload initramfs-factory.bin via tftp from your computer

   example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin

 6. Boot initramfs image by "boot" command
 7. On the initramfs image, back up the stock bootloader and firmware if
   needed
 8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
 9. Replace the bootloader with a uboot.bin image
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing

Notes:

- All LEDs are connected to the GPIO controller on the ath9k chip
  (AR9380) and controlled by it. Those LEDs are probed after probing of
  ath9k chip, so they cannot be handled as status LEDs of OpenWrt while
  booting.

- A reset pin of the internal USB hub is connected to the GPIO
  controller of the ath9k chip, like LEDs above. That hub will be
  detected after probing of the ath9k chip.

- The stock bootloader requires an unknown filesystem on firmware area
  in the flash. Booting of OpenWrt from that filesystem cannot be
  handled, so the bootloader needs to be replaced to mainline U-Boot
  before OpenWrt installation.

MAC Addresses:

LAN    : 1C:B1:7F:xx:xx:60 (config,  0x6 (hex))
WAN    : 1C:B1:7F:xx:xx:61 (config,  0xc (hex))
2.4 GHz: 1C:B1:7F:xx:xx:62 (config,  0x0 (hex) / art, 0x1002 (hex))
5 GHz  : 1C:B1:7F:xx:xx:63 (config, 0x12 (hex) / art, 0x5002 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15432
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>