git.openwrt.org Git - openwrt/staging/noltari.git/blob

   1 From: Sebastian Gottschall <s.gottschall@dd-wrt.com>
   2
   3 current handling of peer_bw_rxnss_override parameter is based on guessing the VHT160/8080 capability by rx rate. this is wrong and may lead
   4 to a non initialized peer_bw_rxnss_override parameter which is required since VHT160 operation mode only supports 2x2 chainmasks in addition the original code
   5 initialized the parameter with wrong masked values.
   6 This patch uses the peer phymode and peer nss information for correct initialisation of the peer_bw_rxnss_override parameter.
   7 if this peer information is not available, we initialize the parameter by minimum nss which is suggested by QCA as temporary workaround according
   8 to the QCA sourcecodes.
   9
  10 Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
  11
  12 v2: remove debug messages
  13 v3: apply some cosmetics, update documentation
  14 v4: fix compile warning and truncate nss to maximum of 2x2 since current chipsets only support 2x2 at vht160
  15 v5: handle maximum nss for chipsets supportig vht160 with 1x1 only
  16 v7: use more simple code variant and take care about hw/sw chainmask configuration
  17 v8: fix some code style issues
  18 v9: use SM/MS macros from code.h to simplify shift/mask handling
  19 ---
  20  drivers/net/wireless/ath/ath10k/mac.c | 54 +++++++++++++++++++--------
  21  drivers/net/wireless/ath/ath10k/wmi.c |  7 +---
  22  drivers/net/wireless/ath/ath10k/wmi.h | 14 ++++++-
  23  3 files changed, 52 insertions(+), 23 deletions(-)
  24 --- a/drivers/net/wireless/ath/ath10k/mac.c
  25 +++ b/drivers/net/wireless/ath/ath10k/mac.c
  26 @@ -2515,7 +2515,7 @@ static void ath10k_peer_assoc_h_vht(stru
  27         const u16 *vht_mcs_mask;
  28         u8 ampdu_factor;
  29         u8 max_nss, vht_mcs;
  30 -       int i;
  31 +       int i, nss160;
  32
  33         if (WARN_ON(ath10k_mac_vif_chan(vif, &def)))
  34                 return;
  35 @@ -2575,23 +2575,45 @@ static void ath10k_peer_assoc_h_vht(stru
  36                 __le16_to_cpu(vht_cap->vht_mcs.tx_highest);
  37         arg->peer_vht_rates.tx_mcs_set = ath10k_peer_assoc_h_vht_limit(
  38                 __le16_to_cpu(vht_cap->vht_mcs.tx_mcs_map), vht_mcs_mask);
  39 +       arg->peer_bw_rxnss_override = 0;
  40 +       nss160 = 1; /* 1x1 default config for VHT160 */
  41
  42 -       ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vht peer %pM max_mpdu %d flags 0x%x\n",
  43 -                  sta->addr, arg->peer_max_mpdu, arg->peer_flags);
  44 +       /* only local 4x4 configuration do support 2x2 for VHT160,
  45 +        * everything else must use 1x1
  46 +        */
  47
  48 -       if (arg->peer_vht_rates.rx_max_rate &&
  49 -           (sta->vht_cap.cap & IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_MASK)) {
  50 -               switch (arg->peer_vht_rates.rx_max_rate) {
  51 -               case 1560:
  52 -                       /* Must be 2x2 at 160Mhz is all it can do. */
  53 -                       arg->peer_bw_rxnss_override = 2;
  54 -                       break;
  55 -               case 780:
  56 -                       /* Can only do 1x1 at 160Mhz (Long Guard Interval) */
  57 -                       arg->peer_bw_rxnss_override = 1;
  58 -                       break;
  59 -               }
  60 +       if (ar->cfg_rx_chainmask == 15)
  61 +               nss160 = arg->peer_num_spatial_streams <= 2 ? 1 : 2;
  62 +
  63 +       /* if peer provides 1x1 nss160 information using max rate
  64 +        * vht information, we reduce local nss160 to 1x1.
  65 +        * consider that it has been observed that some client
  66 +        * devices provide zero here, no matter which transmission
  67 +        * rate is possible. in that case the local nss configuration
  68 +        * will be used at maxmimum configuration possible. (see above)
  69 +        */
  70 +
  71 +       if (arg->peer_vht_rates.rx_max_rate == 780)
  72 +               nss160 = 1;
  73 +
  74 +       /* in case if peer is connected with vht160 or vht80+80,
  75 +         * we need to properly adjust rxnss parameters otherwise
  76 +        * firmware will raise a assert
  77 +        */
  78 +       switch (arg->peer_phymode) {
  79 +       case MODE_11AC_VHT80_80:
  80 +               arg->peer_bw_rxnss_override = BW_NSS_FWCONF_80_80(nss160);
  81 +       /* fall through */
  82 +       case MODE_11AC_VHT160:
  83 +               arg->peer_bw_rxnss_override |= BW_NSS_FWCONF_160(nss160);
  84 +               break;
  85 +       default:
  86 +               break;
  87         }
  88 +
  89 +       ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vht peer %pM max_mpdu %d flags 0x%x peer_bw_rxnss_override 0x%x\n",
  90 +                  sta->addr, arg->peer_max_mpdu, arg->peer_flags,
  91 +                  arg->peer_bw_rxnss_override);
  92  }
  93
  94  static void ath10k_peer_assoc_h_qos(struct ath10k *ar,
  95 @@ -2743,9 +2765,9 @@ static int ath10k_peer_assoc_prepare(str
  96         ath10k_peer_assoc_h_crypto(ar, vif, sta, arg);
  97         ath10k_peer_assoc_h_rates(ar, vif, sta, arg);
  98         ath10k_peer_assoc_h_ht(ar, vif, sta, arg);
  99 +       ath10k_peer_assoc_h_phymode(ar, vif, sta, arg);
 100         ath10k_peer_assoc_h_vht(ar, vif, sta, arg);
 101         ath10k_peer_assoc_h_qos(ar, vif, sta, arg);
 102 -       ath10k_peer_assoc_h_phymode(ar, vif, sta, arg);
 103
 104         return 0;
 105  }
 106 --- a/drivers/net/wireless/ath/ath10k/wmi.c
 107 +++ b/drivers/net/wireless/ath/ath10k/wmi.c
 108 @@ -7552,12 +7552,7 @@ ath10k_wmi_peer_assoc_fill_10_4(struct a
 109         struct wmi_10_4_peer_assoc_complete_cmd *cmd = buf;
 110
 111         ath10k_wmi_peer_assoc_fill_10_2(ar, buf, arg);
 112 -       if (arg->peer_bw_rxnss_override)
 113 -               cmd->peer_bw_rxnss_override =
 114 -                       __cpu_to_le32((arg->peer_bw_rxnss_override - 1) |
 115 -                                     BIT(PEER_BW_RXNSS_OVERRIDE_OFFSET));
 116 -       else
 117 -               cmd->peer_bw_rxnss_override = 0;
 118 +       cmd->peer_bw_rxnss_override = __cpu_to_le32(arg->peer_bw_rxnss_override);
 119  }
 120
 121  static int
 122 --- a/drivers/net/wireless/ath/ath10k/wmi.h
 123 +++ b/drivers/net/wireless/ath/ath10k/wmi.h
 124 @@ -6478,7 +6478,19 @@ struct wmi_10_2_peer_assoc_complete_cmd
 125         __le32 info0; /* WMI_PEER_ASSOC_INFO0_ */
 126  } __packed;
 127
 128 -#define PEER_BW_RXNSS_OVERRIDE_OFFSET  31
 129 +#define BW_NSS_FWCONF_MAP_ENABLE       BIT(31)
 130 +#define BW_NSS_FWCONF_MAP_160MHZ_LSB   (0)
 131 +#define BW_NSS_FWCONF_MAP_160MHZ_MASK  (0x00000007)
 132 +#define BW_NSS_FWCONF_MAP_80_80MHZ_LSB (3)
 133 +#define BW_NSS_FWCONF_MAP_80_80MHZ_MASK (0x00000038)
 134 +#define BW_NSS_FWCONF_MAP_MASK         (0x0000003F)
 135 +
 136 +#define GET_BW_NSS_FWCONF_160(x)       (MS(x, BW_NSS_FWCONF_MAP_160MHZ) + 1)
 137 +#define GET_BW_NSS_FWCONF_80_80(x)     (MS(x, BW_NSS_FWCONF_MAP_80_80MHZ) + 1)
 138 +
 139 +/* Values defined to set 160 MHz Bandwidth NSS Mapping into FW*/
 140 +#define BW_NSS_FWCONF_160(x)           (BW_NSS_FWCONF_MAP_ENABLE | SM(x - 1, BW_NSS_FWCONF_MAP_160MHZ))
 141 +#define BW_NSS_FWCONF_80_80(x)         (BW_NSS_FWCONF_MAP_ENABLE | SM(x - 1, BW_NSS_FWCONF_MAP_80_80MHZ))
 142
 143  struct wmi_10_4_peer_assoc_complete_cmd {
 144         struct wmi_10_2_peer_assoc_complete_cmd cmd;