git.openwrt.org Git - openwrt/staging/blogic.git/blob

   1 From 4f3a00c7f5b2cfe4e127fd3fe49b55e1b318c01f Mon Sep 17 00:00:00 2001
   2 From: Robert Hancock <robert.hancock@calian.com>
   3 Date: Tue, 25 Jan 2022 10:54:08 -0600
   4 Subject: [PATCH] net: phy: at803x: move page selection fix to config_init
   5
   6 The fix to select the copper page on AR8031 was being done in the probe
   7 function rather than config_init, so it would not be redone after resume
   8 from suspend. Move this to config_init so it is always redone when
   9 needed.
  10
  11 Fixes: c329e5afb42f ("net: phy: at803x: select correct page on config init")
  12 Signed-off-by: Robert Hancock <robert.hancock@calian.com>
  13 Signed-off-by: David S. Miller <davem@davemloft.net>
  14 ---
  15  drivers/net/phy/at803x.c | 40 ++++++++++++++++------------------------
  16  1 file changed, 16 insertions(+), 24 deletions(-)
  17
  18 --- a/drivers/net/phy/at803x.c
  19 +++ b/drivers/net/phy/at803x.c
  20 @@ -651,25 +651,7 @@ static int at803x_probe(struct phy_devic
  21                         return ret;
  22         }
  23
  24 -       /* Some bootloaders leave the fiber page selected.
  25 -        * Switch to the copper page, as otherwise we read
  26 -        * the PHY capabilities from the fiber side.
  27 -        */
  28 -       if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) {
  29 -               phy_lock_mdio_bus(phydev);
  30 -               ret = at803x_write_page(phydev, AT803X_PAGE_COPPER);
  31 -               phy_unlock_mdio_bus(phydev);
  32 -               if (ret)
  33 -                       goto err;
  34 -       }
  35 -
  36         return 0;
  37 -
  38 -err:
  39 -       if (priv->vddio)
  40 -               regulator_disable(priv->vddio);
  41 -
  42 -       return ret;
  43  }
  44
  45  static void at803x_remove(struct phy_device *phydev)
  46 @@ -745,6 +727,22 @@ static int at803x_config_init(struct phy
  47  {
  48         int ret;
  49
  50 +       if (phydev->drv->phy_id == ATH8031_PHY_ID) {
  51 +               /* Some bootloaders leave the fiber page selected.
  52 +                * Switch to the copper page, as otherwise we read
  53 +                * the PHY capabilities from the fiber side.
  54 +                */
  55 +               phy_lock_mdio_bus(phydev);
  56 +               ret = at803x_write_page(phydev, AT803X_PAGE_COPPER);
  57 +               phy_unlock_mdio_bus(phydev);
  58 +               if (ret)
  59 +                       return ret;
  60 +
  61 +               ret = at8031_pll_config(phydev);
  62 +               if (ret < 0)
  63 +                       return ret;
  64 +       }
  65 +
  66         /* The RX and TX delay default is:
  67          *   after HW reset: RX delay enabled and TX delay disabled
  68          *   after SW reset: RX delay enabled, while TX delay retains the
  69 @@ -770,12 +768,6 @@ static int at803x_config_init(struct phy
  70         if (ret < 0)
  71                 return ret;
  72
  73 -       if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) {
  74 -               ret = at8031_pll_config(phydev);
  75 -               if (ret < 0)
  76 -                       return ret;
  77 -       }
  78 -
  79         return 0;
  80  }
  81