git.openwrt.org Git - openwrt/staging/linusw.git/blob

   1 From 2679834327b5b8db8a7b0c90b632b81c35f9e271 Mon Sep 17 00:00:00 2001
   2 From: James Hughes <james.hughes@raspberrypi.org>
   3 Date: Thu, 31 Oct 2019 14:39:44 +0000
   4 Subject: [PATCH] net:phy:2711 Allow ethernet LED mode to be set via
   5  device tree
   6
   7 Add device tree entries and code to allow the specification of
   8 the lighting modes for the LED's on the ethernet connector.
   9
  10 Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
  11 ---
  12  arch/arm/boot/dts/bcm2711-rpi-4-b.dts |  3 +++
  13  arch/arm/boot/dts/bcm2838.dtsi        |  1 +
  14  arch/arm/boot/dts/overlays/README     | 28 +++++++++++++++++++--------
  15  drivers/net/phy/broadcom.c            |  9 +++++++--
  16  4 files changed, 31 insertions(+), 10 deletions(-)
  17
  18 --- a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
  19 +++ b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
  20 @@ -334,5 +334,8 @@
  21                 pwr_led_gpio = <&pwr_led>,"gpios:4";
  22                 pwr_led_activelow = <&pwr_led>,"gpios:8";
  23                 pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
  24 +
  25 +               eth_led0 = <&phy1>,"led-modes:0";
  26 +               eth_led1 = <&phy1>,"led-modes:4";
  27         };
  28  };
  29 --- a/arch/arm/boot/dts/bcm2838.dtsi
  30 +++ b/arch/arm/boot/dts/bcm2838.dtsi
  31 @@ -380,6 +380,7 @@
  32                                         /* No interrupts - use PHY_POLL */
  33                                         max-speed = <1000>;
  34                                         reg = <0x1>;
  35 +                                       led-modes = <0x02 0x02>;
  36                                 };
  37                         };
  38                 };
  39 --- a/arch/arm/boot/dts/overlays/README
  40 +++ b/arch/arm/boot/dts/overlays/README
  41 @@ -102,26 +102,38 @@ Params:
  42
  43          eee                     Enable Energy Efficient Ethernet support for
  44                                  compatible devices (default "on"). See also
  45 -                                "tx_lpi_timer".
  46 +                                "tx_lpi_timer". Pi3B+ only.
  47
  48          eth_downshift_after     Set the number of auto-negotiation failures
  49                                  after which the 1000Mbps modes are disabled.
  50                                  Legal values are 2, 3, 4, 5 and 0, where
  51 -                                0 means never downshift (default 2).
  52 +                                0 means never downshift (default 2). Pi3B+ only.
  53
  54 -        eth_led0                Set mode of LED0 (usually orange) (default
  55 -                                "1"). The legal values are:
  56 -                                0=link/activity          1=link1000/activity
  57 +        eth_led0                Set mode of LED0 (usually orange). The legal
  58 +                                values are:
  59 +
  60 +                                Pi3B+
  61 +
  62 +                                0=link/activity    1=link1000/activity (default)
  63                                  2=link100/activity       3=link10/activity
  64                                  4=link100/1000/activity  5=link10/1000/activity
  65                                  6=link10/100/activity    14=off    15=on
  66
  67 -        eth_led1                Set mode of LED1 (usually green) (default
  68 -                                "6"). See eth_led0 for legal values.
  69 +                                Pi4
  70 +
  71 +                                0=Speed/Activity (default)       1=Speed
  72 +                                2=Speed/Flash activity   3=FDX
  73 +                                4=Off                    5=On
  74 +                                6=Alt                    7=Speed/Flash
  75 +                                8=Link                   9=Activity
  76 +
  77 +        eth_led1                Set mode of LED1 (usually green) (Pi3B+ default
  78 +                                "6", Pi4 default "0"). See eth_led0 for legal
  79 +                                values.
  80
  81          eth_max_speed           Set the maximum speed a link is allowed
  82                                  to negotiate. Legal values are 10, 100 and
  83 -                                1000 (default 1000).
  84 +                                1000 (default 1000). Pi3B+ only.
  85
  86          i2c_arm                 Set to "on" to enable the ARM's i2c interface
  87                                  (default "off")
  88 --- a/drivers/net/phy/broadcom.c
  89 +++ b/drivers/net/phy/broadcom.c
  90 @@ -292,6 +292,9 @@ static void bcm54xx_adjust_rxrefclk(stru
  91  static int bcm54xx_config_init(struct phy_device *phydev)
  92  {
  93         int reg, err, val;
  94 +       u32 led_modes[] = {BCM_LED_MULTICOLOR_LINK_ACT,
  95 +                          BCM_LED_MULTICOLOR_LINK_ACT};
  96 +       struct device_node *np = phydev->mdio.dev.of_node;
  97
  98         reg = phy_read(phydev, MII_BCM54XX_ECR);
  99         if (reg < 0)
 100 @@ -345,6 +348,8 @@ static int bcm54xx_config_init(struct ph
 101
 102         bcm54xx_phydsp_config(phydev);
 103
 104 +       of_property_read_u32_array(np, "led-modes", led_modes, 2);
 105 +
 106         /* Encode link speed into LED1 and LED3 pair (green/amber).
 107          * Also flash these two LEDs on activity. This means configuring
 108          * them for MULTICOLOR and encoding link/activity into them.
 109 @@ -354,8 +359,8 @@ static int bcm54xx_config_init(struct ph
 110         bcm_phy_write_shadow(phydev, BCM5482_SHD_LEDS1, val);
 111
 112         val = BCM_LED_MULTICOLOR_IN_PHASE |
 113 -               BCM5482_SHD_LEDS1_LED1(BCM_LED_MULTICOLOR_LINK_ACT) |
 114 -               BCM5482_SHD_LEDS1_LED3(BCM_LED_MULTICOLOR_LINK_ACT);
 115 +               BCM5482_SHD_LEDS1_LED1(led_modes[0]) |
 116 +               BCM5482_SHD_LEDS1_LED3(led_modes[1]);
 117         bcm_phy_write_exp(phydev, BCM_EXP_MULTICOLOR, val);
 118
 119         return 0;